Practical Method for Production of Water Fuel with Piezoelectric

[altrez]

Here is something that is interesting..

-Altrez

[Slovenia]

Slovenia's Website for Power To Be
http://tech.groups.yahoo.com/group/Power1Crystal-PiezoelectricStudyGP/

These are my links to archived files I made from Power1 & Powerme threads & posts archived at Scribd.

Practical Method for Production of Water Fuel with Piezoelectric from OU
http://www.scribd.com/doc/51189669/Practical-Method-for-Production-of-Water-Fuel-From-OU

Best Way to Use Heat From HHO to Generate Electricity
Best Way to Use Heat From HHO to Generate Electricity

Growing Crystals, Piezoelectric Energy Harvesting
Growing Crystals, Piezoelectric Energy Harvesting

Magnets on Fuel Line Experiment
Magnets on Fuel Line Experiment

New One Added Feb 22, 2011
Plasma-Effect-Cosmic-Ray-Amplification
Plasma Effect - Cosmic Ray Amplification

New One Added February 22, 2011
Bedini-Earth-Light
Bedini Earth Light

Best Regards,
Slovenia

Slovenia

Thank you
That would be Very Nice!!

Chet

[Super God]

Just some observations. The transducer causes a water jet to shoot up from it. If the transducer is in the water too deep, the water jet will not breach the surface and the mist effect does not happen. If the jet does breach the water, misting takes place. This leads me to believe that the chamber must be constructed such that the upside down bowl is in the mist area and the water level must be low enough for the transducer to cause it's effect. This is with the stock transformer, mind you. I will rewind it for 36 volts later tonight.

[Slovenia]

Yes, you are right Fishman.  That link was for the ZnO powder to make the crystals and not for ready made crystals.   Very Good!!

I believe the link you refer to is for Zn0 nano podwer, not Zno nano crystals.

[Slovenia]

I think the geometry for the chamber where the transducer sits may be important too and so far I don't have any ideas for it that really make me feel great.  I can think of a lot of possibilities, but none of the ones I'm thinking of give me that warm and fuzzy feeling inside.  You know the one I mean.  I want our project to be successful, so I'm hoping Power To Be will give us a few pointers on this.

A good material for the chamber I feel would be polypropylene, cutting board material.  It's easy to machine, easy to get online, and fairly inexpensive.

We need to get a good working prototype going soon or  we're going to have a lot of folks loose interest.  Power To Be wants us to all take an active part in this project, but I know how things go, a few do all the work while a majority sit in the stands and watch to see if it's a successful venture before helping.  Well guys, we do need your input and their are some hurdles we need to jump over.

We need a good way to plate the crystals on the bowl receiver so that they will stay in place and not easily be vibrated or washed off.  There's serious water activity in the cell and if the plating is not done right, it will wash off the bowl quickly.  I was going to use epoxy to attach my crystals to my receiver bowl, but the still small voice inside me said don't do it that way.

I've found a good brass horn for us to use I think and it's only $6.00 each, but I still haven't found a suitable brass bowl.  My gut is telling me that a good bowl size is approximately 2.5" in diameter and I just haven't found those dimensions yet.  Also, we need the walls of the bowl to be thin enough that they will resonate freely and I'm thinking 1 mm to 1.5 mm might be the right thickness.

Any thoughts would be much appreciated.

Also, I'm getting a gut feeling that we really should have two transducers in the cell like in Power's diagram.  I was trying to keep my price down in my test cell, but anything worth doing is worth doing right.  So, what do you think?