Is joule thief circuit gets overunity?

[WilbyInebriated]

Before you can do that, simple thing of quitting, you have first have to start / contributing!?

which is why i was able to QUIT as well... 

regards...

[ltseung888]

All right, I'm done with you lot. I've tried to help you Lawrence but apparently you do not need my help....even though you have been making great mistakes all along, as your "ac coupling" error shows. I should think that would have humbled you a little bit.

*** That error got me to focus on the voltage fluctuations when I used the battery or the DC Power Supply.  I claimed that the FLEET circuit could produce pulsing voltages back to the Input.  That led me to develop FLEET with "wrong COP" values in the thousands.  On redoing the measurement with DC Coupling, those "wrong COP" FLEETs still give COP>1 with certain frequencies.  The researchers that never make that mistake might never go on that path as they gave up when they saw the COP<1 value.  It is an example I called God's Blessing.  Thanks for pointing out that error before the Universities.  However, I am sure that with the oscilloscope-test-ready board in front of them, they will easily detect the COP>1 situations.
*** The AC coupling got me into the investigation of NEGATIVE POWER much earlier.  Is that another Divine Blessing???


It takes my circuit, as configured now, driving a bank of 24 white LEDs in series-parallel as shown in my last video, over eleven minutes to run down from 1.500 volts charge on the 3 Farad capacitor, to 0.500 volts remaining. The bank of LEDs is dim at that point but by no means dark. I think that if one recharged at 0.750 volts....that would be at around 8 minutes for me with my old 3 F, 5.5 V capacitors .... one might not notice the dimming over the operational period.

*** If you have a twin timer, charge the circuit for 3 seconds and then turn off the power for 3 minutes and repeat, you will probably find that your lights appear to be bright all the time.  If you reharge another rechargeable battery at the same time with the appropriate circuitary, you will be able to compete with G-LED and BSI on their Forever Lighted Lamps.  However, they already applied for patents.

I wonder how long it would take if I had a 10 F capacitor, and a Platinum Visa card, like you. I think it would be more like 24 minutes, or even more.... but that's a conjecture, not a claim. I know better than to make claims for which I do not have solid evidence.
***  So you know that our claim of the demo board from BSI can light up 38 LEDS for an average of over 20 minutes is no exaggeration.  Hudreds of people have seen and played with it already.  Get a 2.3V 10F capacitor. Use your DSO and do your correct measurements with a DC power supply.  You will find that charging your circuit with even 0.4V for < 3 seconds, a single LED circuit can be ON for over 20 minutes.  Your 4 channel DSO will immediately show COP > 1 at some point over these 20 minutes.  I envy you for having such - you do not need to do the many hours of EXCEL analysis afterwards.

Have fun. We'll never know if your circuit outperforms mine or not, will we.

I am sure your results will show similar support that the COP >1 under certain conditions as the 30 top Universities will.  Once we all master the technique of staying on such conditions and use the resulting lead-out energy, there is no World Energy Crisis.  Patrick Kelly's book is a great help.

May the Almighty guide us to benefit the World.

[ltseung888]

Instead of rechargeable Battery A and B.  Use Capacitor A and B.
*** Recharge at the lead-out energy range..... Use DC coupling on your DSO to confirm.  Thanks to TK.

The Forever Lighted Lamps only require a battery to start.  (May even use a hand crank unit).

I shall try it out on my Christmas lights.  You can too.
*** The components in the Lead-out Energy Research Kit can demonstrate the Forever Lighted Lamp if the user use himself as the timer and the swapper!  Providing two 2.3V 10F capacitors in the Kit turns out to be another "lucky decision"?  Or is it Divine Guidance???

All Glory to the Almighty.

[nievesoliveras]

@tseung888


Will you send me an already tried and tested unit, if I pm you my mail address?


Jesus

[bs2012]

Instead of rechargeable Battery A and B.  Use Capacitor A and B.
*** Recharge at the lead-out energy range..... Use DC coupling on your DSO to confirm.  Thanks to TK.

The Forever Lighted Lamps only require a battery to start.  (May even use a hand crank unit).

I shall try it out on my Christmas lights.  You can too.
*** The components in the Lead-out Energy Research Kit can demonstrate the Forever Lighted Lamp if the user use himself as the timer and the swapper!  Providing two 2.3V 10F capacitors in the Kit turns out to be another "lucky decision"?  Or is it Divine Guidance???

All Glory to the Almighty.

Hi Lawrence,

Can I purchase your fleet kit / Forever Lighted Lamp?  I could pick them up from your Tsuen Wan office or any other location in Hong Kong.  Please let me know the price.