Kapanadze Cousin - DALLY FREE ENERGY

[scratchrobot]

Obama  fancy a trip down a rabbit hole ?
https://www.youtube.com/watch?v=MLGItF-Y8Uc

Obama is not from Kenia, he is an Grey Alien like you, there is enough prove on youtube.

[itsu]

  "Wesley sees dots. You see rainbows. I see fakes. Everyone to their own."

    That's one way to see it. Reminds me of the three blind men, and the elephant.

    So, while we're on the subject of seeing...
    My latest video:
https://www.youtube.com/watch?v=7x_t6q4SZt4&feature=youtu.be

Hi Nick,

thanks for the new video, i agree with some remarks from magpwr (video quality) and Dog-one.

You mentioned the screenshot of your scope as from one of the FET's, but it seems it was just laying unconnected close to the yoke.
This x1 probe will pick up any noise from the mains to some fluorescent bulbs/tubes etc. so you hardly can call that a screenshot from one of the FETs.

Better is to use a x10 probe and probe the MOSFETs gate or drain compared to ground (be aware of the max voltage on your scope channels)

When moving the probe to near the kacher lateron in the video, you can see the higher amplitude and higher frequency as you needed to adjust both the V/div. knob
as the time base knob.

One remark concerning the turn direction of your inbetween coils on the ferrite bar (between the kacher and the antenna), they are
both in one direction in your case, while in Ruslan's videos they all show as being one CW, the other CCW, see pictures.


Regards Itsu

[itsu]

Hi Nick ,
Nice see your progress with Mazilli , don't be upset with some opinions . For sure even is not the right path you will learn and evolve with your observation and practice
. Your are only work in one aspect of circuit, the inverter but it could made by many ways and different circuits .
You will need joules in one side ever time ! joules do work you mazilli circuit convert this joules only to another state .

Is supposed you charge the wima caps at output of grenade with high Electrostatic field , to convert this electric field in joules again, and able to do work after stored in the caps .   Did you ever think anytime or calculated how many joules by second you will need, to run the circuit even without load?

What you do with the BEMF  in you Mazilli ?
Way you and others insist eliminate BEMF  whith snubber configurations  ? You can use them to feedback in circuit and e volute your circuit to a  parametric oscillator it will be a good improvement .
Maybe you can think a bit in this my thought .

about Wima caps you can find with lower price .
www.reichelt.de , you can find the Wima capacitors starting from 0,22€.


Good luck Nick

No Bemf in a mazilla (resonance power oscillator) that i know of that needs to be snubbered out, see my screenshot of one of my mazilla MOSFETs here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg460425/#msg460425


If you do not have a mazilla, but an other square wave oscillator, like in Ruslans design (push pull) then you might need heavy snubbering.

Or..... you use the "lossless clamp" design created by verpies early in this thread in the original "Dally" replication, see post #120 on page 9 of this thread here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg338079/#msg338079

and updated just some weeks ago in post #10043 on page 670 of this thread here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg459297/#msg459297


I dusted of my "losless clamps" circuit from my original Dally replication (post #120) and fired it up and it produces the below nice square wave signals:


Be sure to read the post #120 on how to create the primary coils.


Regards Itsu

[NickZ]

  Itsu:
  Good eyes, yes, you're right, the ferite tuning bar is wound wrong, good call, even after having to watch my blurry video.
In the picture below you can see that the ferite rod was at one time wound right, then I must have re-wound it all one way.
I'll correct it, soon. Thanks.
Sorry about the video quality, but my $220 camera just died and won't take any pics. So, I had to use the cell phone camera, which sucks.

  Anyway, I think that you get the idea, as I just wanted to show the Mazilli/yoke/grenade set up working, without overheating, while lighting up some 100w bulbs. I'll get into more scope shots and details on it once I have it tuned better, and working with the Kacher circuit.

   The scope probe that I'm currently using is the 100x, not the 1x or 10x.  The signal I'm getting at the yoke is the exact same shape of signal that the fets are giving off, exactly. So, instead of risking a short circuit to connect the probe to the fets themselves,  I lay it next to the yoke coils, For now, as I'm not looking at value readings, but tuning for the "effect", instead.
But, I'll show what the signal looks like connected to the fets, in my next video. 
  I've tried to order new set of scope  probes, (1x, 10x) but I don't know if it's going to happen yet, as I depend on other people to bring it to me. I am also ordering some of the WIMA caps, as you have.
  What I'm working towards is tuning the various frequencies to obtain this correct heterodyning effect, and that video was just the start of it.

  EDIT: Itsu, this was what the IRFP260N mosfet signal looks like (pic below) with the 100x scope probe connected to the fet's drain, and negative clip to the PS negative rail. At the 10 volts/div setting.
One fet has a slightly higher gain, compare to the other one. The Mazilli is running off of the 24v, 10A PS. 
Does that picture of the scope shot tell you anything?
   

[Jeg]

Or..... you use the "lossless clamp" design created by verpies early in this thread in the original "Dally" replication, see post #120 on page 9 of this thread here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg338079/#msg338079


Be sure to read the post #120 on how to create the primary coils.


Regards Itsu

Hi Itsu
Very clean square output! Do you remember the values of cap c3 and diode d3 that you used in this no.120 Verpies  post?

Thanks