Kapanadze Cousin - DALLY FREE ENERGY

[T-1000]

Greetings 00 and others,

For many months I was reading most of the posts on this forum and many more and guessing I would just Share my Ideas now .

I would like to share my version of a SR193 / Kapanadze coil generator  with massive Cap bank and  for Resonance.
It can produce more then 1 Kw only using 24VDC.
When I have it on 36Vdc, it will produce 2 or 3 Kw Equivalent to many Incandescent very bright bulbs of 100W and also 500W bulbs.

Hi,

Go ahead, show your video with your replica / attempt. Would be nice to see circuit diagram with tuning steps there as well.

kapanadze video 1 2 3 4 ...

Where is your own? If you just copy/paste - the virtual scapyard http://www.overunity.com/7679/selfrunning-free-energy-devices-up-to-5-kw-from-tariel-kapanadze/new/topicseen/#new is right place just not this thread.
Please help us to keep it clean from speculations / not own made stuff / not tested ideas.

Hi magpwr guruji243 is me   

Nice attempts
Just the high frequency pulsed-stuff measurements and scope shots would be nice there along with schematics and tuning.
Also you might check if you have some NMR in place - the Geiger counter would show that for sure.

[Hoppy]

Just a quick report on the attached schematic posted by 00.

For anyone trying out this circuit please do not use the specified diodes as they are liable to overheat and smoke if 12V halogen lamps are used as a load as suggested. The diodes need at least 5A rating for 12V halogen lamps up to 50W. Also ensure that the transformer power rating suits the power rating of the lamp load or that will overheat as well! The lamp does indeed flash brightly and will stay bright all the time the 4,700uF cap is connected. This is because the reactance of the cap in parallel with the diodes reduces the overall resistance of the circuit thus providing more current to the lamp. Increasing the capacitance further increases the current availability and therefore lamp brightness. However, at each step the power consumed from the grid (as measured on a watt meter) is increasing, so no free energy here as the circuit is operating to convention! Scoping the waveform across the lamp shows a distorted half wave sinusoid.

[dllabarre]

Just a quick report on the attached schematic posted by 00.

For anyone trying out this circuit please do not use the specified diodes as they are liable to overheat and smoke if 12V halogen lamps are used as a load as suggested. The diodes need at least 5A rating for 12V halogen lamps up to 50W. Also ensure that the transformer power rating suits the power rating of the lamp load or that will overheat as well! The lamp does indeed flash brightly and will stay bright all the time the 4,700uF cap is connected. This is because the reactance of the cap in parallel with the diodes reduces the overall resistance of the circuit thus providing more current to the lamp. Increasing the capacitance further increases the current availability and therefore lamp brightness. However, at each step the power consumed from the grid (as measured on a watt meter) is increasing, so no free energy here as the circuit is operating to convention! Scoping the waveform across the lamp shows a distorted half wave sinusoid.

00
Did you test this schematic with Halogen bulbs?
Why is Hoppy getting overheated diodes?

Hoppy - can you measure the voltage across the load (bulb)?


Thanks
DonL

[joefr]

Hi Hoppy

I tried this circuit today

This is the wave form across 12V car light bulb

I also noticed increased power consumed with 4700uF cap connected

JoeFR

[magpwr]

hi everyone,

Since i'm new to Kapanadze thread < 2months.

I have spotted a very good video on how to bend copper pipe to form induction coil.This video was made by a plumber.
I am just sharing this since this will be the technique i will applying around 4th week of Oct "not with metal pipe as shown in video to form coil but with pvc instead.To cut cost".

http://www.youtube.com/watch?v=ah_tcY1pZvs

All project on hold for me at this moment due to home renovation preparation while also waiting for several parts to arrive for ou project.Please don't take it i have disappeared in between this period.