Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Kapanadze Cousin - DALLY FREE ENERGY

Started by 27Bubba, September 18, 2012, 02:17:22 PM

Previous topic - Next topic

0 Members and 194 Guests are viewing this topic.

magpwr

Quote from: Jeg on October 04, 2014, 12:21:18 PM
Very nice Mag. If we could find the relative direction of granade also, it would have more sense. If you look at the picture at my previous post attachment, there all the directions can be shown.

Nick if you spoke about this pic that Mag attached, yes it looks like it has 12+12 and heavier gauge wire than the grenade.

hi jeg,

Please follow itsu.We have already sorted out the receiver portion few days ago and i have pasted my coil spec with the number of turns awhile ago for Hoppy.

That's all for now.I need to charge my batteries. :D :D :D :D

Hoppy

Quote from: NickZ on October 04, 2014, 11:58:09 AM
 
  Hoppy: I got my new Mazill crt working now. The problem was a combination of one bad solder joint, and possibly a bad new battery. The device works ok with my 12v, 10 amp battery charger. But, the brand new battery will not hold the charge, and I may have to replace it with another one. Voltage drops too much when the device is turned on. Which also makes the fets heat up, as well, as you have previously mentioned.
My fets, IRFP260N (6 pack) are all a bit different from one another, and so are  their output readings.
I'll screw the fets down in place on the heatsinks when I find the right size drill and screws, as the motherboard heatsinks don't have the mounting hole in them.


Nick,

Good news! Go for a much bigger battery, say 20A/hr or bigger. When you drill holes in the heat sink, make sure you lightly countersink the holes, especially on the surface so that the mosfets lay completely flat on the heat sinks.

Hoppy

Quote from: Jeg on October 04, 2014, 12:21:18 PM
Very nice Mag. If we could find the relative direction of granade also, it would have more sense. If you look at the picture at my previous post attachment, there all the directions can be shown.


I agree, it would be most helpful to have a clear pictorial winding instruction showing directions of wind from a fixed reference point at the start of winding at thin end of the grenade.

d3x0r

Quote from: magpwr on October 04, 2014, 12:13:53 PM
It's ok.I have just cracked\solved this outer coil winding direction mystery  in 3 minutes using another alternative verification approach.




I like the notes on the kapagen coil... (I lost my images so I'll have to dig for it...)
an originalish is heree... you can see the winding directions pretty well... http://www.overunity.com/12736/kapanadze-cousin-dally-free-energy/msg408309/#msg408309

Hoppy

So we have 48-48 cw, 24-24 ccw, 12-12 ccw as viewed from start of winding at thin end of grenade - yes?