Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Kapanadze Cousin - DALLY FREE ENERGY

Started by 27Bubba, September 18, 2012, 02:17:22 PM

Previous topic - Next topic

0 Members and 218 Guests are viewing this topic.

Print
Go Down Pages 1 ... 1158 1159 1160 1161 1162 ... 4758
User actions

itsu

#5795
October 16, 2014, 04:49:05 AM
Quote from: MenofFather on October 16, 2014, 01:57:57 AM
Itsu, thanks, were conected wire 1 and 2?
Wire 1 conected to mosfet drain?

MenofFather,

correct, wire 1 is attached to the drain of the MOSFET, wire 2 to the other side of the Schottky diode.
Basically, the wires 1 and 2 are across (parallel to) the Schottky diode.

Regards Itsu

itsu

#5796
October 16, 2014, 05:18:14 AM
Quote from: T-1000 on October 15, 2014, 06:20:03 PM
2) The Grenade coil - It is receiver wound on tube of 50mm diameter with length of ~21cm length, full winding on it for layer forward and continue with second layer to same direction, then divide its length by 2, put the same cable from the end of 2nd layer until middle and wind into opposite direction direction until end then continue with second layer to same direction, then again divide by 2 and put the wire until middle from end of previous coil and wind into opposite again until end (the last half is in same direction as longest bottom) then continue layer on same direction. Then put wire across top coil and put inside of tube then make exiting under begining of coil. The total length of wire = 1/4 of resonant frequency. Also the inductance is minimal (microH range). The ground is also connected to the wire exiting from top of the coil and should be completely separate to avoid any noise as device is really sensitive to it.

T-1000,

do you mean with the part in bold that the last layer (2x 12) is in the same direction as the first layer (2x 48), meaning CCW?
If so, i doubt that as this below picture clearly shows its also CW as the middle layer (2x 24).

Regards Itsu

MenofFather

#5797
October 16, 2014, 06:03:51 AM
Itsu, did you see what your nanosecond pulse ferite ring and Ruslan is wound different? So Ruslan probarly not get nanosecond pulses! He get 200 volts 300 ns pulses or something similar. Right?

itsu

#5798
October 16, 2014, 07:35:34 AM
Quote from: MenofFather on October 16, 2014, 06:03:51 AM
Itsu, did you see what your nanosecond pulse ferite ring and Ruslan is wound different? So Ruslan probarly not get nanosecond pulses! He get 200 volts 300 ns pulses or something similar. Right?

MenofFather,

i do not see any difference in the connections between the two drawings.
Only the dots are on the other sides, but as both are, that does not have any effect.

Regards Itsu

Void

#5799
October 16, 2014, 08:28:10 AM
Quote from: Enjoykin on October 15, 2014, 11:00:31 PM
Hi Void
Ruslan Kulabuhov interview will be soon on freeenergyinfio channel in english. It is big 108 min.
Reg. Enjoykin

Thanks!
Print
Go Up Pages 1 ... 1158 1159 1160 1161 1162 ... 4758
User actions