Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Kapanadze Cousin - DALLY FREE ENERGY

Started by 27Bubba, September 18, 2012, 02:17:22 PM

Previous topic - Next topic

0 Members and 151 Guests are viewing this topic.

Print
Go Down Pages 1 ... 2487 2488 2489 2490 2491 ... 4758
User actions

Hoppy

#12440
February 26, 2016, 12:46:58 PM
Quote from: Jeg on February 26, 2016, 12:32:19 PM
Hi guys
Hoppy, thanks for reminding me. I'll try the resistance in series to see what is going on.


Jeg,

From what you descrbed in your earlier post, I suggest you use a higher power rated TVS and then use a resistor if necessary. I use 1500W rated diodes for this type of application.

Jeg

#12441
February 26, 2016, 12:50:59 PM
Verpies, can you please explain some more? How is d.t. relates to the current and so to the cross area of the wire?

Hoppy thanks. I'll order tomorrow a couple.

NickZ

#12442
February 26, 2016, 12:59:11 PM
  Ok, so the clamp windings cuts out the HV spikes.  "That's all it does" ?
  Further proof will what it can actually do to the input/output voltages, to reduce the input drawn, by returning some power to the PS. And also, to eliminate over heating of components, as you previously mentioned. That was also supposed to be it's purpose.  Or not? Maybe I misunderstood?
All the while running a full load, to at least what PS wattage (240w-360w)can provide, and also cordinating the HV circuit to be in sync with the induction circuit,  to see or observe IF there is any extra gain at the bulbs. 
That would be the proof, that I'm looking for.


Once Itsu adds the needed 28 turns coil to the 168turns grenade coil, and tuning caps for that LC circuit, we'll see what happens then.
 

verpies

#12443
February 26, 2016, 01:03:15 PM
Quote from: Jeg on February 26, 2016, 12:50:59 PM
Verpies, can you please explain some more? How is d.t. relates to the current and so to the cross area of the wire?
Simply the current carrying capacity of the wire is determined by the average current - not by the momentary pulse current. 
So if you have 20A flowing for 1% of the time, then this is equivalent to 200mA of current flowing all the time, ....as far as wire heating is concerned.

T-1000

#12444
February 26, 2016, 01:09:54 PM
About additional winding on yoke in parallel to primary - connecting just capacitor to it also will dampen BEMF. And if in resonance it will help push-pull to drive Yoke.

Nick,
You're objecting my posts with me not showing stuff but ignoring fact me already on doing replication. And I will make it until end, that's for sure. Then there will be video to share.. ;)
Print
Go Up Pages 1 ... 2487 2488 2489 2490 2491 ... 4758
User actions