Kapanadze Cousin - DALLY FREE ENERGY

[itsu]

Good day All

Quick question regarding the attached photos:
First; Can anyone tell me which two signals these are supposed to be?
The higher freq is the 3rd Harm. of the lower.  So how does this relate to Ruslan's or Sergie's device?  Which two coils have only a 3rd harmonic difference in Frequency?

Second: On the Karcher Sync- Are these signals taken from the Inductor winding?  If so, shouldn't the V & I be in Phase (zero shift) *if* the LC circuit is in Resonance?  Why would this drawing be showing a approx. 90 degree phase shift between V & I ?

Any thoughts on this would be appreciated.
take care, peace
lost_bro

LB,

concerning your First question, there was some discussion earlier (as always) about those signals, like here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg420180/#msg420180    and in further posts.

And here: http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg420554/#msg420554 and in further posts.
But no clear answer was presented as far as i was concerned.


On your Second question, i was asking that same question here:  http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg463132/#msg463132
when discussing that timing diagram here:  http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg463092/#msg463092
and lateron here:  http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg463771/#msg463771  and some posts further.

I think the answer is that V and I when in (series)resonance should be in phase, but only when looking from the input, meaning the 3 turn coil.
There we see that V and I are in phase, but as V is distorted its a not so nice picture.

When looking at V  across the different components (coil or cap) we always will see a 90° phase shift compared with I.

About your "another question" i dunno.

Itsu

[AlienGrey]

In other drawing.
Itsu, now you see diference betwen your conection and Ruslan?

What difference

http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg420180/#msg420180

[T-1000]

It is sad news today because John Bedini passed away yesterday. I believe he made a contribution towards free energy even if it was just to get people interested in the topic. He will be missed.

That is sad news. Also unfortunately he took some secrets to the grave like others..

Quick question regarding the attached photos:
First; Can anyone tell me which two signals these are supposed to be?

The 3 traces are showing how train pulses are fed to flyback transformer (with deadtime to repeat effect into flow after switching power off) then modulation happen in point B so the frequency go up.

T1000,

Thanks for this baseline circuit diagram. Please ask Akula to put some meat on the bone and provide winding / construction details for the coil configuration. Also, explain what is in the rectangular box at the top of the diagram.

The top box with Russian writing represent low frequency generator.
The coils shown there are represented as grenade winding or similar top load "antenna" + bifilar cw/ccw + inductor. The wire lengts/etc are tied on each location unfortunately and are varialbles to find out.

[Jeg]

T1000,

Thanks for this baseline circuit diagram. Please ask Akula to put some meat on the bone and provide winding / construction details for the coil configuration. Also, explain what is in the rectangular box at the top of the diagram.

Thanks T1000. To add on Hoppy's request, please may you ask if vertical coils are in the same core with horizontal coils (as these are indicated in the attached drawing).

[Hoppy]

Thanks T1000. To add on Hoppy's request, please may you ask if vertical coils are in the same core with horizontal coils (as these are indicated in the attached drawing).

Jeg,

I'm looking at the vertical coils being a flyback trafo with the horizontal coils being separate.