Kapanadze Cousin - DALLY FREE ENERGY

[NickZ]

Well Nick,

I'm working in Zwitserland at the moment took a part of the decoration with me.
As i followed the other thread i  only can say it is always a misunderstanding issue,...  and with people who are less polite,..  probably a little frustrated you will get very fast in a escalting mode.
No one to blame..  but when everybody reads there own posted and see opinions and mostly the people who start to point will speed up the escalating proces even more.

Never forget,,  most of us..  maybe all are here for the same reason.... we need to deal with respect to others also who don't want to tell everything..  (which i do understand...... "why tell it all in 10 minutes which cost you personally 2 years" ..  so i understand guys like Nelson and will never discredit them.)..  people who do are childisch in my opinion.
Thats why i respect everybody on this forum...  and the goal is to leave every person in its own ...."who and what he is".... 
We all do this to all here unless someone is stupid,... not skilled,..  etc.


But back to the setup....  i like the statement from a.king..  explaining the DS and kapanadze item about the one cap plate to be charged...
At this point we are still stuck together....  only Geo showed he gets the most gains out of his cap_plate.

Cycling this charging effect at the best impedance matching situation is key.....
Again..  i still believe RF, Nelson and a.king and other persons did help us the way up already.

greetings

   Concerning Nelson, I would trust him as my own brother, who is also called Nelson. Name that I gave him when he was born.  I am always nice, to him, or you or any others that don't insults me with every post that I make to them. Like some people we know. Anyway, I'm not going to communicate with Rick, and keep getting my ass kicked, ever again. I had my share of insults, and I'm back at home, (the Asylum). The head nurse Ratched, never noticed that I had left. She's been taking too many tranquilizers. Well, I really should of never left.
   We'll see what becomes of a.kings new posted diagram, which should not be difficult to undertake. And itsu will continue on, well, elsewhere, as you may already know. Hoppy is still listening to the sermons, and still wants to be believer. Right Hoppy?

[AlienGrey]

And what circus diaphragm is that then your referring to ?

[magpwr]

HI I don't understand how you have it wired up. where you have it wired up from the cap after the 3 or 4 wind coil
where is fed then ?

Hi AlienGrey,


I have attached  image base on my circuit layout.This is based on AKula circuit with 4017 in block diagram but i suspect need to follow old circuit diagram if i need to see usable voltage at output if i am using mere 12volts .


This circuit is a mix of old and new circuit of Akula.


This is just 1st actual trial test.But unexpected trumpet waveform produced looks interesting.


https://www.youtube.com/watch?v=T7TqGsQIYkQ

[Sergh]

Who hears in this video loud rattling sound?

https://www.youtube.com/watch?v=5qpU3IFAnU8

Looks like a transformer? Not. It would be quieter.
Probably a sound source is found. This is a vibration pump. Widely distributed in the territories of the former USSR. Many varieties of design. General - loud rattling sound when working. When installed in a well, no sound is heard. May create high pressure. Raises water from a depth of 60 meters. It works only from AC. Rubber suspension and an iron anchor matched to mechanical resonance with the frequency of the network. Power consumption 150 - 250 watts.

https://youtu.be/fPTg9KTQ6K8?t=100


https://www.youtube.com/watch?v=TNs7xH1b1_g

[Hoppy]

Interesting! Here is another video: https://www.youtube.com/watch?v=PrkuSfnfIeA
Sounds very similar to Kapanadze's device.
May also explain why his device cannot run for too long, as it would overheat the pump which under normal operating conditions would be cooled by water.