Rosemary Ainslie Circuit Demonstration June 29, 2013 Video Segments

[powercat]

Rosemary should take the polygraph test, then we will know the difference between incompetency and deception

[poynt99]

Rose has announced a possible demo Aug 4.

[TinselKoala]

I wonder what is left to demonstrate.

Will she -- or rather Donovan Martin -- perform any _real_ tests of their claims? Like any genuine attempt to show the heat produced by the oscillations _alone_, without any contribution from the Q1? Will they continue with the false claim that the Figure 3 scopeshot is somehow able to be made HONESTLY under the conditions claimed? Will we be treated to another four hours of inept incompetence and utter disrespect for their audience?

Meanwhile, she continues to demonstrate her mendacity and ignorance with every post.

But those instantaneous wattage values can certainly be extreme enough to degrade that resistor as efficiently as a power surge will blow your average light bulb.   Which is why we used resistors in excess of 5 watts.  I have ALWAYS known that our resistors are valued at 25 watts.  Good heavens Poynty.  I ORDERED them and PAID for them - against the wattage that we determined was required.  WHY are you trying SO HARD to imply that I did not know those wattage values?  Is this based on the general need to emphasise how little I know about that circuit?  Because we're all rather sick and tired of that spin.

nonono no NO....

Some of us are laughing very hard right now.

[TinselKoala]

She's STILL at it! I almost said "unbelievable" but it's all too believable, really.

Addressed to .99:

I have ABSOLUTE confidence in Weir's expertise.  Correspondingly I have very little confidence in your own.  The more so as I MOVED the function generator's terminal REFERENCE to it's position in the attached schematic - ON YOUR ADVICES.  You and others on open source - went to some considerable lengths to advise me that by positioning that reference at the common position with Channel 1 and 2 probe references - that we no longer could rely on the measurements across our Rshunt. 

And she goes on in that vein, again making stuff up, insulting people who are clearly much more competent than anyone she can muster in her own defense, and attacking and insulting based on her own mendacity and imagination.

In every photograph of her apparatus, going all the way back to the single mosfet design, the BLACK FG output lead can be very clearly seen to be connected to the COMMON CIRCUIT GROUND. That is, in the position that bypasses the CVR. In the March 2011 Demo, it is there. In the photographs of the single mosfet version, it is there. In the images of the apparatus that appear on PESN, with the new resistors in place.... it is there. In the video of the June 2013 demo, it is there.  The position shown in the schematic given in Paper 1 HAS NEVER ACTUALLY BEEN USED BY AINSLIE, not even to gather the data in the papers. The BLACK FG lead has ALWAYS been positioned as it was during the recent demo. The schematic in Paper 1 only appeared AFTER this issue was "poynted" out to Ainslie. Prior to this, the schematic given was the single mosfet version and the Black FG lead was not even included on the schematic.

Ainslie has NEVER used the correct schematic (BLACK FG output on Transistor side of Shunt, ground-isolated FG)  in any of her demos or reported tests, and it was certainly NOT used in the experiments described in the papers.... her own blog posts made at the time of the experiments prove this.

Below images are:
1. The schematic presented in the March 2011 demonstration and claimed by Ainslie until April 18 or so. No BLACK FG lead shown-- which CONCEALS the current path through the FG bypassing the Shunt.
2. The schematic which "now" appears in the papers, but which was not acknowledged by Ainslie until late April 2011, after the FG bypass problem was shown, along with the four Q2 mosfets being in "backwards".
3. The schematic that Ainslie has always ACTUALLY used, but has never published, with the 5 mosfet device, and also shows the BLACK FG position used for the single mosfet device.
4. A photo of the single mosfet device, clearly showing the Black FG clip at the common circuit ground.
5. A screenshot of the 5-mosfet device demonstrated in March of 2011, clearly showing the Black FG clip at the common circuit ground.
6. A screenshot from the June 2013 demo, clearly showing the Black FG clip at the common circuit ground.
7. And finally... her latest confabulation of mendacity, insult and misrepresentation.

The "correct" schematic given in their Paper has never been used by Ainslie and Martin, and they don't know how to ground-isolate their FG at all, even though Donovan Martin is clearly aware of the issue.

[TinselKoala]

I forgot to include the PESN version, sorry.