Partnered Output Coils - Free Energy

[EMJunkie]

one other question; does the magnetic core have to be a kind of a looped one like ring or square for a good return magnetic path?

@Wistiti,

Another good Question!

Short Answer: No

Long Answer: In some configurations, the Operation of each Partnered Output Coil will Uni-Polar. This means to get a Sine Wave output, one must have two sets of Partnered Output Coils. This is something I think its a little premature to get into at this stage. I can further advance in this area as we progress!

Lets just say, for people that already are in an understanding, Permanent Magnets introduce a Singular Flux Polarisation, E.G; South/North! In one Direction! This introduces added complications!

Or it can work to with a straight one like a  ferrite rod?

Yes if this is what you have available. Start with this!

Important: I do recommend, however, to start with a Closed Core! Either C Cores, U I Cores or similar! Toroid (Ferrite or other, Rings) don't seem to work. Not enough Leakage Inductance/Loose Coupling!

Kind Regards

   Chris Sykes - hyiq.org
   To Reach New Horizons!

[hanon]

Hi,

What happens if there is no gap? You loose the "effect"?. In other words: is the gap mandatory on the setup?

It would be great if you tell us a rough design to strat from. Turns, wire, core, voltage, amperage, frequency,gap width... I think you will gain credibility with this, better than refering to the gut feeling. Some of us are mot very skilfull in building those experiments.


Thanks

[EMJunkie]

Hi Hanon,

Good Question!

Short Answer: Yes Sometimes.

What happens if there is no gap? You loose the "effect"?. In other words: is the gap mandatory on the setup?

Its not always the case however! Sometimes separating the Partnered Output Coils by a small distance is enough!

It would be great if you tell us a rough design to strat from. Turns, wire, core, voltage, amperage, frequency,gap width...

Well, I though I have done much more than this already?

URL: http://www.hyiq.org/Downloads/Guidelines%20to%20Bucking%20Coils.pdf

Is there not enough information in this document to get an idea on where to start? I recommend to start at the start! Don't expect your first device to run your house! Like I said in the document: "For every one device that works, expect 10 devices that don't. But, don't give up, keep trying."

If one follows the basic Principals I have given, it does work! Replicate my experiments first if you need somewhere to start.

I think you will gain credibility with this, better than refering to the gut feeling. Some of us are mot very skilfull in building those experiments.

This is the sort of thing that really makes me think that the Human Race will never progress past the point we are stuck in now! Hundreds of Researchers/Experimenters in History have given freely, to humanity, their work. Some have not! Some Charlatan's have paraded the arena and done the wrong thing by others!

I have not asked for Money! I have not asked for anything in return!

I have spent many hundreds of hours preparing information, animations and diagrams for others!

My Credibility is Solid!

I have shown countless other devices from Inventors/Researchers throughout History that have used the same technology!

People just don't understand, one needs to use their intuition to make this work!

Its not hard, it is actually very simple! Its very Cheap to do a simple experiment! Practice, play with the device, Learn what it likes and doesn't!

My Inductors shown in the below device, are standard Off the Shelf: http://www.jaycar.com.au/productView.asp?ID=LF1312

I ask you, Bill Alek gave most everything, is his credibility better off for it? No, people say: "Measurement Error" without even having the slightest understanding of what's going on! Or even the slightest idea on why it works, or how an Excess Energy Gain might even be Achieved!

I have given you all this information, How, Why and all details to follow this up!

I remind everyone, Bill is an EE, to call it "Measurement Error" is ridiculous especially with no evidence to the contrary!

Kind Regards

   Chris Sykes - hyiq.org
   To Reach New Horizons!

[hanon]

I really appreciatte all your work, from the bottom of my heart. It is amazing. I suppose you won´t like to share in public the COP you have got. I understand.

What I meant with my previous post is that if you want this info to spread around the world you need to go viral. This is a must.  For going viral you need a "critcal mass" of replicants to spread this technilogy. If not you will fail.

In order to get a critical mass, IMHO, you need three features in your device: 1- Easy to replicate a working prototype (maybe a small one) ; 2 - Full description of the construction/operation; 3 - Open source all that info in many forums/sites.  This is my opinion the requisites to, at least, have a chance to get that "critical mass" of followers. If you do not reach going viral then this technology could wait decades in the pipeline.

Good luck and keep on !!

[EMJunkie]

Hi Hanon,

I really appreciatte all your work, from the bottom of my heart. It is amazing. I suppose you won´t like to share in public the COP you have got. I understand.

Thank You  - In the last device shown, the best I was able to achieve was COP = 1.7

What I meant with my previous post is that if you want this info to spread around the world you need to go viral. This is a must.  For going viral you need a "critcal mass" of replicants to spread this technilogy. If not you will fail.

Yes, it seems we (The Human Race) is doomed for failure! Seems some of us cant get past the bare Animal Instincts of Greed, Kill or be Killed mentality's? Why is it that we have so much value on the position's that nature can simply take in a minute? Yeah we all like a comfortable Life, but how much is too much. The wealthiest 1% will very soon surpass ALL the rest of us! Is the Human Race worthy of being saved?

The Meek shall inherit the Earth! 

In order to get a critical mass, IMHO, you need three features in your device: 1- Easy to replicate a working prototype (maybe a small one) ; 2 - Full description of the construction/operation; 3 - Open source all that info in many forums/sites.  This is my opinion the requisites to, at least, have a chance to get that "critical mass" of followers. If you do not reach going viral then this technology could wait decades in the pipeline.

Completely agree Hanon!

The problem is, its not just a case of taking x, y z and assemble! One must play with it a little to get the best result! Materials can change the device's operation.

Good luck and keep on !!

Thanks, I know youre a really good person! We have had communications before. I am here on this thread to help with this, this surely also gives credibility to the device. How many inventors/Researchers have ever done this before?

1: Top Coils (Preferred)
2: Bottom Coils Also works but requires slightly more Gap/Loose Coupling.

Where (A) and (B) are the inter-connections between the Partnered Output Coils! The other terminals are the Output!

Kind Regards

   Chris Sykes - hyiq.org
   To Reach New Horizons!