Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of this Forum, I am asking that you help him
by making a donation on the Paypal Button above
Thanks to ALL for your help!!


Partnered Output Coils - Free Energy

Started by EMJunkie, January 16, 2015, 12:08:38 AM

Previous topic - Next topic

0 Members and 4 Guests are viewing this topic.

Print
Go Down Pages 1 ... 770 771 772 773 774 ... 1774
User actions

picowatt

#3855
June 25, 2015, 08:04:36 AM
Quote from: tinman on June 25, 2015, 07:57:28 AM
As i stated,that was my screw up, as i was talking about the bucking effect,as like would be seen in your partnered coil setup,as it is an effect that adds the torque to the mechanical output of the motor.

Sorry for taking up too much room in your thread,i just didnt see much point in starting a thread about my device,as it has just about gone as far as it's going to go. I have only the final video,and measurements to go,and what will be after that is yet unknown.

Tinman,

I am still interested in seeing a scope capture showing the noise floor of your in/out rails.

With AC coupling, higher vertical gain, and increased sweep rate, I'd like to actually see a bit of brush rate noise.

PW

EMJunkie

#3856
June 25, 2015, 08:08:04 AM
Quote from: tinman on June 25, 2015, 07:57:28 AM
As i stated,that was my screw up, as i was talking about the bucking effect,as like would be seen in your partnered coil setup,as it is an effect that adds the torque to the mechanical output of the motor.

Sorry for taking up too much room in your thread,i just didnt see much point in starting a thread about my device,as it has just about gone as far as it's going to go. I have only the final video,and measurements to go,and what will be after that is yet unknown.

@Tinman - Read your words, and hear your meaning. Good Luck!

   Chris Sykes
       hyiq.org

tinman

#3857
June 25, 2015, 08:25:39 AM
Quote from: picowatt on June 25, 2015, 08:04:36 AM
Tinman,

I am still interested in seeing a scope capture showing the noise floor of your in/out rails.

With AC coupling, higher vertical gain, and increased sweep rate, I'd like to actually see a bit of brush rate noise.

PW

What-you mean like the below scope shot's?
First scope shot before the diode.
Second scope shot after the diode,and large cap removed.

picowatt

#3858
June 25, 2015, 08:36:41 AM
Quote from: tinman on June 25, 2015, 08:25:39 AM
What-you mean like the below scope shot's?
First scope shot before the diode.
Second scope shot after the diode,and large cap removed.

Tinman,

Yes, like that...

When you say "large cap removed", does that mean the cap mounted to your perf board is still in place?

Do you have any similar captures from the input side?

PW

tinman

#3859
June 25, 2015, 09:10:28 AM
Quote from: picowatt on June 25, 2015, 08:36:41 AM
Tinman,

Yes, like that...

When you say "large cap removed", does that mean the cap mounted to your perf board is still in place?

Do you have any similar captures from the input side?

PW
Yes,cap still on perf board.
Input wave forms are smooth,even without the caps,only very thin spikes from brush noise-nothing like the output.
Print
Go Up Pages 1 ... 770 771 772 773 774 ... 1774
User actions