Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Is this the first selfrunning overunity motor w/o batteries ? Mike?s motor

Started by hartiberlin, February 14, 2007, 08:30:03 PM

Previous topic - Next topic

0 Members and 5 Guests are viewing this topic.

Print
Go Down Pages 1 ... 140 141 142 143 144 ... 195
User actions

Peterae

#705
March 17, 2007, 08:37:09 AM
Cheers Darren
The other thing do you think i will be ok putting 3 magnets on each stack ,so 6 lots of 3 magnets.
I have enough gap for 3.
Also just spun up with 2 magnet stack and get 2.25 VAC with spin from hand on the main winding tho.
Peter

z_p_e

#706
March 17, 2007, 09:06:20 AM
Hmm,

I've looked at Mike's setup (the collage photo) and I would estimate that he has an air gap of between 1 - 1.5cm between magnet and coil.

If 3 magnets brings you closer than 1cm, then I'd stick with two. If two is more than 1.5cm gap, then perhaps glue something to the bottom of the first magnet to prop it up a bit closer.

Darren

Peterae

#707
March 17, 2007, 09:07:32 AM
Ok Darren 2 it is i can bend the coil at the corners anyway to get the correct gap, i get abou 1.1 VAC by hand spinning on the Gen winding, altho i only have the shaft to spin, where as Mike had a flywheel. I think Mike got 2.5VAC

z_p_e

#708
March 17, 2007, 09:10:51 AM
Quote from: Peterae on March 17, 2007, 08:37:09 AM
Cheers Darren
The other thing do you think i will be ok putting 3 magnets on each stack ,so 6 lots of 3 magnets.
I have enough gap for 3.
Also just spun up with 2 magnet stack and get 2.25 VAC with spin from hand on the main winding tho.
Peter

So that's about 3.2Vp. Mike implied that spinning the rotor by hand and feeding the bridge from L2 should charge up the cap to 6V didn't he?

What is your air gap with two magnets?

Peterae

#709
March 17, 2007, 09:20:21 AM
Cant put me cap on yet that measurement was OC
7mm gap at top and 7mm at bottom now ive bent the coil a bit.
Still plenty to get yet, i want some 8mm washers and nuts.and havnt got the resistors yet LOL, i can out on my day off Monday to get these, i have every thing else.
Print
Go Up Pages 1 ... 140 141 142 143 144 ... 195
User actions