Chas Campbell free power motor

[d3adp00l]

Sounds great, can't hardly wait.

[Humbugger]

you beat me sorry i get out of bed at 9 am 

yeah just sent you a mail man to confirm, also we will have a full write up on our on line uni, by some one who can do the most easy to follow practical plans Patrick Kelly.
http://www.panaceauniversity.org

This date is confirmed ill be there with camera on Sep 1st! The whole world community is going to owe Chas a lifetime of thanks and gratitude, i will also be arranging a funding charity drive for him for those who can say thanks, to look after him in ANY way.
He wishes to at least get some renumeration for his Grand kids, Also the Grant foundations will want to talk to him about his advanced system (he deserves it for this gift to the world), but the proof is here, he always said what he was going to do and he has done it!

here comes History, i would sell your OIL shares

Hi Ash...

Can you give us any details about how the testing (if any) will be done?  It sounds like Charles is a really neat old guy with a heart of gold and who deserves a lot of respect and our kindness for his long hard efforts.  I can see how it would be pretty tough to be a hard-nosed scientist evaluating without bias under the circumstances.

Before I "sell my oil shares", however, I think it would be prudent to not only have a showing and more video of the machine but to really make sure it does something other than storing a lot of slowly-accumulated kinetic energy.  There are several quite successful commercial flywheel-based backup/stabilization power systems on the market already; none claim any overall energy gain nor does any provide such.

To indicate any actual energy gain, you understand, one would have to accurately measure total watthours input vs total watthours output; from a dead stopped condition to full runup and back to a fully run down stopped flywheel.  It would not suffice to neglect the energy required to get the flywheel up to speed, obviously.

That is the quickest, most error-proof skeptic-proof approach, especially if the test is repeated with the calibrated watt-hour meters swapped in position from input to output.  If only instantaneous power in watts, rather than accumulated energy in watthours or wattseconds, can be measured, then an accurate test will take much longer and it gets much trickier and far more prone to error.

If a clear excess of total output energy can be honestly shown, using reasonably accurate calibrated instruments and accounting for all the input energy, then I'll be pleased to donate some funds to the Charles Campbell fund you mentioned.  

Have a good visit and give the old guy a high-five from the Humbugger regardless of the outcome of any scientific testing.  Thanks!

Humbugger

[nwman]

I just have to put my two cents in. I agree with Hum' that by simply putting a watt meter in front of the machine and one at the output and letting it start up, run for a few hours maybe, and then turn off and compare the readings. Then if it seams to be real try switching the two meters' positions and doing it again. I would think you could also easily install a simple three way power switch that would two on and one off position. So position would be:

1)On - Wall outlet power
2)On - Power from the other end of the generator feeding back.
3)OFF

Then by simply turning it to position 1 until its up to speed and then to position 2 which would loop the power back around and hopefully keep it running. Then you could put a watt meter in line after the generator/alternator which you can watch and see if the watts ramp up or down. Theoretically with no regulators and "if it worked" the machine would feedback into itself and cause a rapid increase in speed. Probably blowing up in just a few seconds after switching. That would be fu... interesting!

Tim

[helmut]

you beat me sorry i get out of bed at 9 am 

yeah just sent you a mail man to confirm, also we will have a full write up on our on line uni, by some one who can do the most easy to follow practical plans Patrick Kelly.
http://www.panaceauniversity.org

This date is confirmed ill be there with camera on Sep 1st! The whole world community is going to owe Chas a lifetime of thanks and gratitude, i will also be arranging a funding charity drive for him for those who can say thanks, to look after him in ANY way.
He wishes to at least get some renumeration for his Grand kids, Also the Grant foundations will want to talk to him about his advanced system (he deserves it for this gift to the world), but the proof is here, he always said what he was going to do and he has done it!

here comes History, i would sell your OIL shares

Hi Ashtweth

Perhaps you can find a Network Line there to establish a online Connection via ICQ

helmut

[ashtweth_nihilisti]

Hi all, Earl has already suggested the DC in and DC measurements out method , its posted early in the thread  so do some more reading

We have already completed a DC box to test this, plus we will have another qualified electrician with some other instrumentation there on the day. Dont worry loads and DC measurements will bed explored, not simple numbers on a watt meter.

Humbugger  thats a good point, perhaps we will get enough on the day for you to reproduce and to apply this method. i know once we do we will be applying your method and reporting back for the board.

@helmut  Im Told ICQ is a way to spy and hack your system so i avoid it