Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Successful TPU-ECD replication !

Started by mrd10, June 12, 2007, 05:12:47 AM

Previous topic - Next topic

0 Members and 39 Guests are viewing this topic.

Print
Go Down Pages 1 ... 3 4 5 6 7 ... 358
User actions

MeggerMan

#20
June 12, 2007, 08:09:39 AM
@Jason,
Great results for 2 frequencies - you just need to prove your input power.

When I did my mosfet tests last night at around 1MHz I also noticed voltage fluctuations on the PSU, except I think mine went down, but I cannot be sure.
I think Stefan is correct and you need to totally isolate the PSU using inductors and capacitors from the TPU.
My PSU is rated 30V at 2.5A but can go to 3A and 33V, this is the very first test for the PSU I did - full load 33V x 3A = 100W.

Another thing you could do is to add another lamp in parrallel.

@Robby,
You read my mind, some AA size Nickle-metal-hydride batteries, 9-10 off should be OK for 0.5A at 1.2V each.


Bypass capacitors:
See page 6 for the recommended capacitors for high frequency gate drive.
http://www.ixysrf.com/pdf/driver_ICs/DEIC420.pdf
0.01uF x 8
0.47uF x 4
4.7uF x 4

Regards
Rob

Earl

#21
June 12, 2007, 08:15:06 AM
Hi Jason, hi All,

One thing to be careful about is that either RF or X-Energy gets into your power supply and causes the pass transistor to fully conduct.  This could easily cause the output voltage to climb to 40+ Volts, even though the regulation circuit with its potentiometer adjust can never reach this high.

I strongly suggest using a battery to replace the power supply.  At the ends of the battery leads where they reach your circuitry, you should have at least three parallel C's, an Electrolytic, and two disc ceramics each a different value, like 1nF and 100nF.

Regards, Earl
"It is through science that we prove, but through intuition that we discover." - H. Poincare

"Most of all, start every day asking yourself what you will do today to make the world a better place to live in."  Mark Snoswell

"As we look ahead, we have an expression in Shell, which we like to use, and that is just as the Stone Age did not end for the lack of rocks, the oil and gas age will not end for the lack oil and gas, but rather technology will move us forward." John Hofmeister, president Shell Oil Company

nong

#22
June 12, 2007, 08:27:57 AM
Hi Jason,

Wow...... :o

Im next....    :P




Merkhava

#23
June 12, 2007, 09:04:11 AM
Hi All,

@ Jason

I understand the point of using LC filters to choke/shunt away RF back surges that would "frak" with your power supply.

I may be in the minority here on my next point...

For the test run on the ECD using a bank of AA rechargeable batteries to replace the PS, I would not want any LC filters in the circuit that would block and shunt away the power pump coming back from the Mobius collector. I would want the Mobius to attenuate I-flow and eventually reverse flow power back into the batteries to recharge them as the Mobius is powering the load (40W light bulb). The batteries are just chemical capacitors used to kick start the device. After the magnetic turbine effect is up to speed and pumping energy from the vacuum, the batteries may then be irrelevant.

If you can demonstrate a 40W light bulb operating for say... maybe 10 minutes... at full brightness and the AA batteries all stay at full charge, then you will have one heck of a demonstration to cheer about.

Eventually a setup can be made where the battery bank is replaced by a bank of capacitors that are kick started by a strong magnet across a coil.

See the video about anomalous continuous charging of a capacitor by a magnet:
http://www.youtube.com/watch?v=5iGEsVaIftk

Robby

Bruce_TPU

#24
June 12, 2007, 09:15:18 AM
Jason,

Thank you and Great Job!  The video's were awesome and will one day be classics for the TPU history.

I look forward to the .pdf and further experimentation.

Historic events are made up of historic people, and we have such a group of us assembled together, for such a time as this...!

Thank you for the safety information about the screening.  We will be using that technique now before starting my own experiments.

Psalm 150:6     ;)
Bruce 
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.
Print
Go Up Pages 1 ... 3 4 5 6 7 ... 358
User actions