Successful TPU-ECD replication !

[wattsup]

@ramset

Here is the location of my ftp OU site.
http://purco.qc.ca/ftp/

Thanks for pointing out @Edges (for short lol) post.

I wonder why it was put in the JuleThief thread.

Really interesting idea of the antenna wire, but I do not think it is, simply because that pattern could be caused by the outer taping of the toroid. The width of the tape could be hugging inside a wire turn and give that effect, that is not visible anywhere else around the toroid.

Then you would have to ask yourself, if it is antenna wire on the LTPU, then where is it in the other tpus.

But one thing is very funny that I have just noticed on that photo. It shows the two center toroids, one in the front of the other. Now if those toroids are the exact same size and build, and given the perspective of the photo, the front toroid should be seen as bigger then the back toroid. But take a good look at them. lol

Now look at his second photo of the LTPU ring, I don't think it is made of metal or magnets. It could have an inner channel with wires going around like a tesla coil primary but this also I doubt. For me the use of that ring is totally useless as a structural requirement, but, if the platform on the inside of the LTPU was raised (to hide the starter batteries), as I have shown before, then that outer ring would help keep the illusion from being too visible.

But good work and I am glad some are still looking at the tpus and finding interesting things.

wattsup

[onthecuttingedge2005]

Otto recently said the ECD is not the way but it was a stepping stone to his present works.

Also.......................

Please show me where this is seen, said, referred to, etc.

Hi Wattsup.

my post investigation on the wire Steven Mark's uses:
http://www.overunity.com/index.php?topic=6123.msg227990#msg227990

look at my post Reply # 12512

Jerry

[wattsup]

@edge

Please look at my post above your last one. You may be right or wrong but what is most important for me is that someone else is looking. Good initiative and keep it up.

 

[onthecuttingedge2005]

@ramset

Here is the A of my ftp OU site.
http://purco.qc.ca/ftp/

Thanks for pointing out @Edges (for short lol) post.

I wonder why it was put in the JuleThief thread.

Really interesting idea of the antenna wire, but I do not think it is, simply because that pattern could be caused by the outer taping of the toroid. The width of the tape could be hugging inside a wire turn and give that effect, that is not visible anywhere else around the toroid.

Then you would have to ask yourself, if it is antenna wire on the LTPU, then where is it in the other tpus.

But one thing is very funny that I have just noticed on that photo. It shows the two center toroids, one in the front of the other. Now if those toroids are the exact same size and build, and given the perspective of the photo, the front toroid should be seen as bigger then the back toroid. But take a good look at them. lol

Now look at his second photo of the LTPU ring, I don't think it is made of metal or magnets. It could have an inner channel with wires going around like a tesla coil primary but this also I doubt. For me the use of that ring is totally useless as a structural requirement, but, if the platform on the inside of the LTPU was raised (to hide the starter batteries), as I have shown before, then that outer ring would help keep the illusion from being too visible.

But good work and I am glad some are still looking at the tpus and finding interesting things.

wattsup

doing metal pixel comparison is easy, just take a known metal like steel and do a pixel analyisis of the known metal then compare it to the control pixel color of known metals, the pixel color is close to steel and I say this because there is always lighting differences in picture and video so it will always be an approximation and never a true verification. but it is a best guess at that. nothing more.

the ones they call pixel people could verify it if they have resources to alloy pictures of decent quality. it is like a finger print, differences in light just smudges the verification technique but leave it to your best educational guess which sometimes need to occure. I am a pixel person myself but not as good as some that are out there who are addicted to it.

I still concure that it is steel and or magnetized steel at best, I could be wrong but i doubt it.

Jerry

[otto]

@guruji

I suppose you have my pdf and all needed to build a ECD TPU.

It was made for grown up people that could understand what I did but as I see here are a lot of children.

Otto