Overunity.com Archives is Temporarily on Read Mode Only!


Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
You also can visit us or register at my main site at:
Overunity Machines Forum



Longitudinal wave research

Started by MarkSnoswell, July 28, 2007, 06:31:29 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Print
Go Down Pages 1 2 3 4 5 6 ... 15
User actions

MarkSnoswell

#15
August 03, 2007, 07:18:26 PM
I was just reviewing the longitudinal wave work of Stanislav & Konstantin AVRAMENKO
http://www.rexresearch.com/avramenk/avramenk.htm
and of Prof. Dr-lng. Konstantin Meyl
http://www.meyl.eu/go/index.php?dir=10_Home&page=1&sublevel=0

While this work in undisputable and of fantastic potential both systems require a single wire or a good ground connection between transmitter and reciever. This is a big problem if you want to power a portable device like a cell phone... or if you want to develope a communications network based on longitudinal waves... I think I have a very simple solution to this :)

This will be very easy and cheap to test. As part of my ongoing research into the basics I plan to test simple new longitudinal wave transmitters and recievers when I get back (late August). In addition to being a fundamental part of TPU like devices there are many opportunities for lonngitudinal waves in the transmission of power and in telecommunications. If anyone is interested in participating in tests in this area just let me know.
Dr Mark Snoswell.
President of the CGSociety www.cgsociety.org

Bruce_TPU

#16
August 04, 2007, 12:03:24 AM
I found this nice description at a link off of one of Mark's aforementioned sites.
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Motorcoach1

#17
August 05, 2007, 02:08:30 AM
IN Teslas single wire power tranmission the LMD coils were passive to the collector if i can find the diagram I'll post it the coils were not grounded , just left open but the wire off the coil was distributed along the leingth of the wire (collector or the transmission line ) only the antenna was grounded between the tank capicotor to ground. no other ground. coils were run static once started and power removed (spark gap to the cap and back fed to the coils , when entergized the power was cut off due to the static feild generated.

Bob Boyce

#18
August 06, 2007, 04:10:04 PM
In my replication attempt of a larger scale Tesla Radiant Energy Collector, a large spiral coil at the top of a 30' mast, was connected to the hot side of a primary tank coil via an adjustable spark gap. The cold side of the primary tank coil was connected to an identical spiral coil buried in the ground around the base of the supporting PVC mast. A ground rod was connected to the outside point of the ground spiral.

One thing to be sure, winding longitudinal energy coils with stranded wire seemed to put the kabosh on those coils being able to carry longitudinal currents well. I made that mistake with the larger guage wires first used in the intermediary bifilar coils. They just would not tune well at all.

Bob

Jdo300

#19
August 08, 2007, 06:43:04 PM
Hi All,

This issue of the receiver being grounded has always bugged me. I have always wanted to build a Tesla wireless power transmitter just to play with it. I was especially inspired by the one that Marco posted on the forum a while back. I'm very curious to see what would happen if you were to have more than one receiver pulling power from the transmitter. Would the transmitter 'perceive' the load from the receivers? If not, then one could conceivably have power multiplication simply by adding more receivers for the same source. Or, you could put the transmitter and the receiver together as one and use feedback to increase the gain of the system.

God Bless,
Jason O
Print
Go Up Pages 1 2 3 4 5 6 ... 15
User actions