Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Circuit setups for pulse motors

Started by Nastrand2000, September 16, 2007, 10:46:33 PM

Previous topic - Next topic

0 Members and 35 Guests are viewing this topic.

Print
Go Down Pages 1 ... 33 34 35 36 37 ... 95
User actions

Ren

#170
October 05, 2007, 06:06:39 PM
Quote from: Nastrand2000 on October 04, 2007, 08:35:34 PM
Hey Ren,
I hooked up one of the coils as a generator coil and ran my motor at 5 volts .05 amps. The coil generates about 15+ volts into a cap 35mF cap 370 volt rating. With a 25 volt  3300 mF cap, It charges it too 14.5 volts. This is while I'm charging a 9 volt battery, I can't go without a load on this setup. The spikes are too high (like 300 to 400), I don't want to inadvertently fry something  like my power supply. It cost me around a 170$.
Jason


Interesting. How many turns on the generator coil? Air coil? Hook it up to a bridge and see how many volts it produces....

I gotta start winding a large coil, I think thats the only thing holding my design back right now. I just cant scrape the funds together and renovate the house at the same time! Oh well, patience is a virtue.. ::)

Jase, good luck with your classes/exams, hope we still see you from time to time in here.

Nastrand2000

#171
October 05, 2007, 08:57:36 PM
Ren,
The coil I was using for the gen coil is the coil used to drive this motor http://www.youtube.com/watch?v=tIOdl7H6qzA&eurl=http%3A%2F%2F7%2Egmodules%2Ecom%2Fig%2Fifr%3Furl%3Dhttp%3A%2F%2Fwww%2Egoogle%2Ecom%2Fig%2Fmodules%2Fyoutube%5Fvideos%2Exml%26nocache%3D0%26up%5Fprefs%5Fversion%3D
It is an air coil run through a full wave bridge rectifier. I don't how many turns, however it is bifilar wound 24 gauge and 2 inch in diameter by 3/4 inch thick. Hope that helps.
Jason

Nastrand2000

#172
October 05, 2007, 11:50:52 PM
After further study I have found some interesting phenomena with stacked gen coils and driver coils (stacked together resonating together with alternating magnets passing) that may be of some service to those looking at the field of coil resonance vs. output.
Jason

Nastrand2000

#173
October 06, 2007, 12:12:47 AM
This might further my research into these stupid pulse motors :P god only knows how much time I've spent on them. Very interesting to say the least. A video soon of this setup.
Jason

Nastrand2000

#174
October 06, 2007, 12:21:39 AM
I just tried running my setup at 12 volts, it's too much for the transistor ( you could stack them to help....but you lose efficiency by doing that).
Jason
Print
Go Up Pages 1 ... 33 34 35 36 37 ... 95
User actions