TPU - General Discussion

[Grumpy]

@Grumpy,

I guess you wanted to be more generic. In this case you are right. However, what you have said is not correct. Assuming all the conditions are ideal, no limit for power, frequency, core saturation, no coil impedance and so on and on and on? if I keep the input current (practically flat input voltage) rising in the linear mode I would get a perfect flat DC output.

Kames.

That is why I said "to a point".  Lay all that other stuff on him and he'll be snowed.  I know from his other posts that he is looking to get some pulses - so I directed my comment in that direction.

[innovation_station]

funny you all mention 5vdc plused

i did this some time ago  i plused it in to a coil with 90 deg winds to the core the bemf was huge  it peaked my meter  interacted with my speekers  and blew the fuse in my meter 5v in 1000 vdc  (on the meter) out  pulsed by hand  it read on the ac side as well peeked at 750v

the fuse was 750vac .8 amp

the base coil was square 

use  a cap and diode  to play around with   

ist

it may just shock you   lol!!

[wattsup]

@IS

I get the same thing just pulsing a battery with a primary of an AC/AC transformer and measure right off the battery. If this could be rapidly pulsed, I'd be interested in the real results cause I saw voltages in the 750s also. But I was only pulsing by hand.
(As usual)

@All

Thanks for your helping me on this. z_p_e thanks for your reply. I may be EE dumb but I'm far from OU stupid. (Hey I should use this as my slogan. lol)

Whatever we are doing in OU, chances are we're moving AC or DC or DC to AC or AC to DC or AC to AC, so........... what the hell is happening to DC to DC. What a bummer.

You can use a rheostat in AC and burn it up in DC. Done that.
You can use batteries and create other demands to bring down the DC side-voltage but that only wastes juice. Done that. Bahhhh.
I'm just pissed off that DC to DC has to be so damn fuzzy. Is there a missing link like maybe BC for Best Current? lol

Don't mind me. I'm also pissed off that all magnetic field systems waste at least two fields. The mono magnet is not around yet to cap each end. Another little known missing link?

The other alternative is using these electronic DC to DC converters or PWMs that are actually acting like straight line fancy resistors and diodes that do not permit any flyback to return through it back to the source. I call them dead enders. You can push juice but don't expect anything back. Otherwise you have to be an EE brainiac like Honk and find the milli-seconds where you can transfer juice into tanks at the right time. Jack, you're a lucky man.

So in actuality, Tesla's knowledge of converting DC with rotor contacts, like Erfinders' circuit, is still the best way of creating DC movements via cap discharge while permitting flyback return and battery recharge. These guys are really on the ball for natures simplest way. When Leedskalnin said everything is made of tiny magnets, are they AC or DC? Just jok'in.

I guess SM must have been pissed off also, until he found a way of doing his conversions through the ether via magneto-acoustic-vibrations. Did I say that?

Just found this for the nonEEers (OK EEers also. lol) Totally great site.
http://hyperphysics.phy-astr.gsu.edu/hbase/hframe.html

[singerxyz]

On a meditation page, http://www.jetcityorange.com/meditation/
I just read about a frequency used in China like Shumann to meditate-

the Chinese fundamental frequency at 344.12 Hz

Something to play with...

[jacob]

... wether it is 7.3 ,5000,or 35,000 who knows?  ...

Gee Lindsay, you just gave away the magic formula! Let's see if anyone can make good use of it.

I wonder where the 1,2,3 frequency mix myth comes from.


Jacob