Selfrunning cold electricity circuit from Dr.Stiffler

[DrStiffler]

Hi all,

I connected Dr. Stiffler's SEC to an Ironhead HHO test Cell which I had built last summer. It has one center negative plate and on each end there is a positive plate and in between each positive and negative center there are 8 neutral plates on each side. All plates are stainless and are spaced 1/8 th of an inch center. Please note that in the video I say 1/16 th of an inch which is not correct, it's 1/8".  The size of the plates are 2 inches square. This is the first time I was able to get HHO gas production from pure distilled water (no electrolite added)

Here is a youtube video: http://www.youtube.com/watch?v=a5y2dzXdGho

Thank you Dr. Stiffler for sharing.

Added: I forgot to mention that the core in my tuning coils is cracked so it's stuck and I can't tune for best efficiency.

Luc

@gotoluc
Send me a private email and I will try to mail you another core or coil, which ever might be best.

[DrStiffler]

@Dr.Stiffler
LOL - its was a compliment of the highest degree!!!!
I cant find any translations of AV's work. Only interpretations by Frovlov and thats as good as it gets. Is this all you had to go on??? I think the subject needs a little more attention that a brush off!

@scraven
"A brush off?" Do your home work, there is plenty of information available and I am not about to do the work for you.

Unless you have positive contributions to this thread they will not be welcome or tolerated, so please change you agenda which is vary obvious.

Thank you for you future compliance.

[gotoluc]

@gotoluc
Send me a private email and I will try to mail you another core or coil, which ever might be best.

Thanks Dr. I just sent you a PM. Did you receive it?

Luc

[nickle989]

@gotoluc .... you beat me to it ... I am waiting for my board .... take a look at the Bob Boyce design but use the Dr's power.  I believe that a greater production can be achieved by syncing the frequency to the plate spacing, it is not key to using Bob's frequency's as much as it is bringing the cell into resonance, one of my ideas was to tune each SS plate to the same frequency by anealing, started this but it takes forever maybe now I will have to complete at least 7 plates ... plate area is also one of the keys in HHO production at least what I have seen in my tests.  I think that Dr. Stiffler's SEC is also creating an envelope of harmonic frequencies but without a spectrum analyzer I think it would be pretty hard to detect.  When using distilled water you are creating an almost capacitor ( I am putting that there as some may not know this) but when using an electrolite the capacitor effect would diminish.  I believe that is why your voltage is on the rise.  What did the voltage start with?  You may see better results if you move the power leads to the outside of the cell ... you will need to recondition the plates though before you will see the results as they are aligned atomically different right now.

Nice work!

If you have a small toy hydrogen cell see what kind of power you get back.  That would be courious endever.

[gotoluc]

@gotoluc .... you beat me to it ... I am waiting for my board .... take a look at the Bob Boyce design but use the Dr's power.  I believe that a greater production can be achieved by syncing the frequency to the plate spacing, it is not key to using Bob's frequency's as much as it is bringing the cell into resonance, one of my ideas was to tune each SS plate to the same frequency by anealing, started this but it takes forever maybe now I will have to complete at least 7 plates ... plate area is also one of the keys in HHO production at least what I have seen in my tests.  I think that Dr. Stiffler's SEC is also creating an envelope of harmonic frequencies but without a spectrum analyzer I think it would be pretty hard to detect.  When using distilled water you are creating an almost capacitor ( I am putting that there as some may not know this) but when using an electrolite the capacitor effect would diminish.  I believe that is why your voltage is on the rise.  What did the voltage start with?  You may see better results if you move the power leads to the outside of the cell ... you will need to recondition the plates though before you will see the results as they are aligned atomically different right now.

Nice work!

If you have a small toy hydrogen cell see what kind of power you get back.  That would be courious endever.

Thanks nickle989.
You are exactly right about the use of electrolite with this kind of energy. When my cell reached 80 volts on just pure distilled water I added a tad of baking soda just to see what would happen. The voltage dropped to about 40 volts and it all just seem to slow down production. Also the battery effect went down much faster when I cut the power, So for all of you out there wanting to get closer to the real way to break the bonds of H2O this I think is a better route to take. I myself never persued brute force HHO after testing since I felt it was not the correct way.

I also think that resonance will be a key factor in a productive HHO cell.  However I fell to achieve that we will have to use a more natural geometry,  maybe like a sphere shape container with a centerred resonating anode, more like the Keely stuff.

Anyway, I hope we can all work on this soon, since gas is killing ALL in more ways than one.

My vote to the Dr. would be 50% HHO and 50% heat since heat is also killing our pocket books for us in Canada.

Luc

Added: here is a link to a video of what I believe to be a real working model: http://www.youtube.com/watch?v=ZxnEQssJ4FQ