Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Nathan Stubblefield Earth battery/Self Generating Induction Coil Replications

Started by Localjoe, October 19, 2007, 02:42:39 PM

Previous topic - Next topic

0 Members and 76 Guests are viewing this topic.

Print
Go Down Pages 1 ... 267 268 269 270 271 ... 809
User actions

Bruce_TPU

#1340
February 11, 2008, 07:20:52 PM
Hello all,

Back to the bench.  I retested my voltage (dry) and it is .02 volts.  No ma's.  The following pictures make no sense to me, especially where the compass points away from the coil on the right side where you see  most of the fourth tier of winding.  Each picture is titled with it's description.

I need to finish winding now.  Will check in later.
P.S.  I bought my relay from Radio Shack tonight.

Cheers,

Bruce

Edit:
Well, I have run out of copper wire, again.   :(  I have one half of the fifth and final wrap to go.  I have so far used 75 feet of iron and copper wire.  I probably will use about 15 feet or so, more to finish.  I also have used 2 yards of 100% cotton and need 1 more yard of material.

I will finish tomorrow night and place it into some water for a voltage and amperage test.  I will then remove it and wind my secondary onto it.
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Freezer

#1341
February 11, 2008, 10:37:24 PM
Winding this thing is hard.  :-[  Weird that it can hold voltage being seeming completely dry.  I'm getting about .3 volts without having even wet it.  Maybe its the moister in the air or capacitance.

jeanna

#1342
February 11, 2008, 11:05:49 PM
Quote from: Freezer on February 11, 2008, 10:37:24 PM
Winding this thing is hard.  :-[  Weird that it can hold voltage being seeming completely dry.  I'm getting about .3 volts without having even wet it.  Maybe its the moister in the air or capacitance.

Nice job. It looks authentic!

I agree winding them is hard.

Before you add any magnets, Freezer, please take readings all around the thing the way Bruce, did. This way we will be able to compare similar compass readings.

Beautiful job esp with the spool.

Thanks,

jeanna

Bruce_TPU

#1343
February 11, 2008, 11:06:44 PM
It looks good Freezer!

I see that you are not running your layers in series.  I think this is good.  You will be able to test with them in parallel.  I am curious as to what the differences will be.  Mine are all in series as everyone knows.

Cheers,

Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Freezer

#1344
February 11, 2008, 11:52:57 PM
Thx guys.  I hope its worth the winding hehe.

@Jeanna

I will take some readings all the around once finished.

@Bruce

I was thinking that each should flow in opposite directions to each pole at the ends.  I will try hooking it up each of the 4 ways to test.  I could go on forever with the layers, I guess I will max out the two wooden ends though.
Print
Go Up Pages 1 ... 267 268 269 270 271 ... 809
User actions