Nathan Stubblefield Earth battery/Self Generating Induction Coil Replications

[Pirate88179]

@ mramos and all:

Did you not see my just recent post about the 3.8mA I got this afternoon?  That's almost twice what I had before.  Not a bad increase.  The led is at about 75% brightness as you can see from the pictures I posted of this test.  I do not short out the cap.  I just place the annode of the led back into the circuit.  Let it sit on my table and after a 5 minute charge on the cell outside (after being dead shorted and tested at 0) burned almost 30 minutes. This feels to me like we are getting somewhere. This led is just as bright, if not brighter, than any of my red led keychain lights that I use in my business.  I can read with this in a dark room by shining on a page of writing. I realize it is not 100% but, I have no way to measure that.  The led is rated at 20mA (maximum) and I am reading almost 1/4 of that, but, I think there is more than I am able to read here, or it would not be near so bright.  Would you agree?  It would not be pulsing off and on at 60hz or whatever hz when running on just the cap would it?  This led is brighter than my neighbors solar garden light, I just don't know how much jusice is really out there.  George priced the carbon rods atlike $2.50 ea. for 3/4 dia. from Mcmasters.  Check an earlier post, you can save some money.

Series or parallel?  That is the question.  I thought the capacitor was wired in series but I am not sure now that there is a question. It's all just positive to positive and neg. to neg. (see photo)  If this is different, please tell me. the only confusing thing about the photo is the copper wire that goes to nowhere.  That is my mechanical switch that I close to the + side of the led to complete the circuit. I hope this helps.  All I know is I started with .85vdc and have 1.9. I started with .5mA and now have 3.8mA.  If we can keep this up, we will get there. (the blue wire is-, the red wire is+)

Bill

Darn it.  It says I have already submitted my post and I did not!  I changed the name of the picture so this would not happen and...oh well.??

[jeanna]

Thanks Bill,
Great work!
I (I was too busy with my own documentation to stop and reply)
so the line of electrodes went from N to S 2 graphite rods linked -1  Mag block - 2 zn spikes linked together?

It is so brilliant and so out of the box. Bravo.

I will replicate with my materials in a couple of days. Hopefully it will be clear on tues.

Happy New Year Everyone

jeanna

[Pirate88179]

@ Jeanna:

Thank you, and Happy New Year to you as well!

@ Bruce:

Thank you for your explanation.  Here is yet another very crude drawing of todays cell arrangement.  Please feel fee to ask any questions as this may be the single worst drawing yet.

HAPPY NEW YEAR to everyone!!!

[Artic_Knight]

bill i noticed you are using png picture format, this is a relatively uncompressed and very large format. try opening your pictures and resaving them as .jpg  this will drastically cut the file size of the pictures and you should be able to post a couple (if the forum permits) in one posting.i seen one picture at 3 meg in here, jpg could reduce it 6 times to .5 meg.

to the person attempting some coils, i have seen some diagrams of flat coil tesla coils, i wonder if that would perform better than the wire wound around an iron core?  if it was bare wire and wound flat it would be a large copper plate sort of speak and would conduct electricity like our pipes is but also tap into the magnetic field perhaps? it would most likely do best burried as ours is.

my replication of a tesla which i will use with my iron pipe is using very fine wire and wound around a wooden pole roughly 1/4 inch thick, its tedious but i think it will produce a wonderful antenna type as tesla was famous for, and i think it may be directly based with the earth batteries and currents, i think it may let us draw more current but we will see what the tests show.  at this time im mostly playing with the ground poles as the others have done

[Pirate88179]

@ Artic KNight:

Thanks for the advice but, I just checked the properties of my pictures and they are saved as jpegs. They originally come out of the camera as bitmap which this site does not accept so now I save them all as jpeg.  Why would this change when uploading????

@ All:

I was just outside looking at the cell in the dark.  A couple of things.  First, I just remembered that when I first tested with the arrangment as seen in my crude drawing posted earlier, a 6" long earthworm came up out of the ground about 5" from my magnesium block like his ass was on fire! I didn't think they could move that fast.  Then, about 2 seconds later, a 3" long centipede came up a few inches away.  What does this mean?  Or just coincidence?

One big question I have is why did my mA increase when I am tieing my electrodes together in what is basically a parallel arrangement? (2 on the +, 3 on the -)  I have one idea.  as we have guessed, amps I believe are tied to SURFACE AREA.  I think these tests make a good case for it.  What do you think?  Only thing that does not fit is the volts went DOWN using this setup like you would expect in series.  Very strange.  does this have something to do with why the earth battery cells do not like series?

Bill