Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Self Running Micro TPU, with closed loop.

Started by EMdevices, November 12, 2007, 11:49:58 PM

Previous topic - Next topic

0 Members and 9 Guests are viewing this topic.

Print
Go Down Pages 1 ... 79 80 81 82 83 ... 139
User actions

Bruce_TPU

#400
December 09, 2007, 01:23:17 AM
@ Sanmankl

Here is my latest schematic update.

Holiday Cheers,
Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

4Tesla

#401
December 09, 2007, 04:50:59 AM
@plengo
I made the following circuit on a simulator based on the circuit linked in my previous post.  It works in the simulator, but didn't build the circuit on my breadboard to test it.
To your specs that you need.. 3v in, 2.7v out, and 18.3mA with a duty cycle 90/10 (90 on / 10 off).. to switch to 10/90 (10 on / 90 off), swap the 1k and 10k resistors and for 50/50 use two 10k resistors.  To change the frequency change the size of the caps (both same size).

4Tesla

Two Transistor Oscillator
Edit: Don't need the diodes

sanmankl

#402
December 09, 2007, 05:37:27 AM
Quote from: btentzer on December 09, 2007, 01:23:17 AM
@ Sanmankl

Here is my latest schematic update.

Holiday Cheers,
Bruce

@ Bruce,

Thanks. I'll give your circuit a go. See if I can do more....?

Cheers, sanmankl

plengo

#403
December 09, 2007, 10:00:09 AM
@4Tesla
what software are you using for the simulator?

Fausto.

4Tesla

#404
December 09, 2007, 12:14:53 PM
@plengo
The diodes aren't needed in that circuit... cleaner output.  Increase collector resistor value to 220 ohms to keep under 20mA.  Here are the links to the free schematic and SPICE simulator software that I am using.

I found this free software for making schematics:
http://www.expresspcb.com/

I found this free SPICE simulator:
http://www.analog.com/en/content/0,2886,0%255F1206%255F162825%255F0,00.html?ref=ASC1285

4Tesla
Print
Go Up Pages 1 ... 79 80 81 82 83 ... 139
User actions