Muller Dynamo

[neptune]

@Romerouk . Welcome back , even if it is just one visit ,
@All . Please no shark feeding frenzy this time . Give the guy room to breathe .

[altair]

so the LED is directly at the input of the DC2DC converter and it has R1 in series with the LED which is
102= 10^2 Ohms= 100 Ohms.

A resistor marked 102 is 1000 ohms !

[Tudi]

Thanks romero for dropping by and mostly thanks for the strength that you managed to publish what most of others were not able to do before you. You are a great man.

@stefan : I think the diodes are the end of the coils ? the current rectifiers ?

[baroutologos]

Hi all,

I have been looking arround here and folowing most of the attempts to replicate the device I have presented and all I can see is that most of you are going in the wrong direction.
In my previous posts I have really told you all but beople can see only what they are familiar with.
You all see magnets rotating in front of the coils... , at 1240rpm we get too low voltage...maybe at 1034 we get better... that is just an ordinary alternator/dynamo but this one was a bit more than that.
If you are considering to build a very efficient dynamo then you are on the right track if you want to investigate more then use your brains.
Here are many people very clever but I think that is their handicap (not all but some)
'My friend' Baroutologos (who started all my current problems) was always in conflict with me regarding my simple way to approach every device I started, but he was going arround in circles because the law of physics are not permiting,...  many...
There is a lot more to be discovered and maybe change or add to the existing laws of physics.
For all who are not really seeing a bit more in here is no point to spend your time and money, wait until those few will manage to understand and you will have more details.
I wont be here to guide anyone as I am considered a master of 'magic (hoax) and maybe I am.
I am already in a lot of .... I don't need anymore.

Best regards to all,
RomeroUK

PS: don't wast time with that LED, it is powered back from the driving coils via the recovery diodes too simple to be seen and  understood...

Hey Romero,

i have said that i am sorry for the trouble caused to you regarding our forum. This was not intentional and i understand your frustration... Nothing more really to say. Just i am sorry.

Regarding the experiments, perhaps you are right about me, but it is not an easy task to replicate something that it is supposed not to have be done before and specially if i have never have done it. Right? It is not a thing that happens everyday, so i ask to be excused.

Anyway, perhaps you think that i will waste resources, but i will replicate your device as closely as possible and be helped by others experimenters here.
I hope you do not mind... Anyway, glad to have you back.

Salutes,

ps: perhaps i should refrain from replication attempts a bit

[hartiberlin]

Hmm,
so where is this recovery diode exactly ?

Is it D1 or is it D2 ?

As the LED need to light up it should be D2,
but then the switch would have no effect...

Hmmm....

If it is these 2 freewheel diodes of the 2 driver coilpairs,
then this also will not light up the LED at the input of the
DC2DC converter ?

Okay resistor is almost 1000 Ohms,
so the LED light should light up until
about 2 to 3 Volts.
depending at which LED current it still shows light.

When the input LED of the DC2DC converter still has
1 mA, the 1000 Ohm resistor will have 1 Volts on it
and the LED will have the threshold voltage of about 1.7 Volts, so
it adds up to 2.7 Volts at 1 mA.
So with 2.7 Volts of input voltage the LED will still light
up with a brightness of 1 mA current through it.

The real question is now,
where exactly is this mysterious recovery diode...
See the circuit diagram below...