Thane Heins Perepiteia.

[MeltDown]

YES THEY HAVE PLENTY SINCE THEY MANUFACTURE LAMINATED CORES ON SITE.

SO HERE'S THE DEAL:

1)
YOU NEED TO CREATE A GOOD - LOW RELUCTANCE FLUX PATH FROM THE PRIMARY TO THE SECONDARY TO KEEP THE PRIMARY CURRENT LOW.

2)
THE SECONDARY TO PRIMARY RETURN FLUX PATH HAS TO BE HIGHER SO THAT THE SECONDARY INDUCED BEMF MAGNETIC FIELD STAYS IN THE SECONDARY AND SELF REGULATES THE VOLTAGE ACROSS THE LOAD.

3)
IF YOUR PRIMARY CURRENT OR POWER FACTOR INCREASES UNDER SECONDARY LOADING YOU ARE SCREWED.

4)
HAVE A LITTLE CRYING FIT AND THEN START AGAIN BY MAKING A PRIMARY WITH A HIGH ENOUGH RELUCTANCE TO DELIVER PRIMARY FLUX WITH LOW POWER BUT NO "ROOM" FOR SECONDARY INDUCED FLUX TO COUPLE BACK TO THE PRIMARY.

5)
THE PRIMARY SHOULD BE OPERATED AT OR VERY NEAR SATURATION.
IT MAY BE ADVISABLE TO USE A DC FIELD TO HELP SATURATE THE PRIMARY FLUX PATH.

6) "GET THE FLUX OUTTA HERE"
OR BUILD THE "BIG BANG" BI-TOROID SO THE BEMF INDUCED FLUXES ARE ATTRACTED TO THE OUTER CORES AND THE HYSTERISIS CURVES OF THE CORE MATERIAL DELAY THE SECONDARY FLUX ENOUGH BEFORE IT IS ALLOWED TO MAKE IT BACK TO THE PRIMARY AND CAUSE THE PRIMARY IMPEDANCE TO REDUCE THUS DRAWING MORE CURRENT FROM THE SOURCE.

CHEERS
T

Hi Thane,

It is me TheBuzz, MeltDown and yes.. CabinBoy. :-) I kept getting banned but I am hooked on free energy so I had to get all techno to get my OU fix.

Thanks for all that information. It is clear that you understand this really well and have devoted a lot of time and thought to it. I am planning to do the same and hopefully contribute something to your work.

I started with a laminated core out of a grow light and didn't finish. I'll try to finish that this week and let you know how it works out. Don't hold your breath since magnetics is not where my experience is but I have always held the magnetics people in high respect. It is as much an art as a science.

If I wasn't banned from Canada for a little marijuana incident back in the 70's I would bring some beer to  Ottawa and spend the day bugging you. In fact I would be a Canadian right now since I was all set to marry a girl from BC until that came up. Dodged a bullet there huh? :-)

[MeltDown]

Thane, I know you are busy but did you ever get a chance to connect the HV coils on the California Christmas coil in series and compare output? I think that could teach us something.

[innovation_station]

your banned bull sh!t   from canada .....   for weed !!!!!   lololololol   now i have herd it all 


bring your pot smoken ass back and get to work!!!!!

ist

unless of course you were invloved is some big TROUBLE    pot is a joke as is the laws regarding it 

FRIENDS OF MINE WERE 1 OF THE FIRST 5 IN CANADA TO HAVE THERE TICKET 
ok  my friends parents how is that     go read up on it   lol lol   you should know better than to doubt me 

sorry THANE....   

a visit to meet you is still on my list .... 

[MeltDown]

FRIENDS OF MINE WERE 1 OF THE FIRST 5 IN CANADA TO HAVE THERE TICKET 

I just find that so difficult to believe.

[CRANKYpants]

Thanks for all that information. It is clear that you understand this really well and have devoted a lot of time and thought to it. I am planning to do the same and hopefully contribute something to your work.

IT IS ALL ABOUT BALANCE WITH THE BI-TOROID TRANSFORMER - BALANCING PRIMARY CORE RELUCTANCE WHILE NOT SACRIFICING PRIMARY POWER AND CREATING A SECONDARY WITH LOW ENOUGH RELUCTANCE THROUGHOUT THE LOADING RANGE.

THIS IS WHY THERE IS NO "COOKIE CUTTER" KIT - EACH TOROID, EACH PRIMARY, WIRE CHOICE, SECONDARY LOADING, SOURCE FREQUENCY, COUPLING CO-EFFICIENT, CORE SIZES AND CORE PERFORMANCE HAVE A ROLE TO PLAY IN THE BALANCING ACT.

T