Joule Thief

[innovation_station]

just to note, i've gotten a couple of axial lead inductors used as the 'transformer'; they become inductively coupled and run very efficiently ..producing around 45 volts, oscillating at about 5Mhz.

do you own a camera?

: )

you have made great coments in the past few pages ... 

time for you to make a video !

: )



now just imagine ....  i made my 1.5vdc pulse motor run from a cam board holding tank and a banger cap at 350vdc 200uf ... 

i'd probally blow the damm magnets right off the plastic wheel ... 

what do you think ?

: )

still runs on a aa ...  : ) 

but i increased my input ...  like 50 times .. nevermind amps .. as per cap value ..

here is a simple fun test ...  for everyone to try ...  discharge a cap of 200uf at 1.5 vdc ...  ok fine  no big deal ... 

now charge that same cap to 350 volts grab a screw driver you will need it .. DO NOT TOUCH IT .. IT BITES .. SO DO I   if you havent noticed! ... 

now short IT ...   BEHOLD CAVEMAN ...  ITS FIRE ! ....   OOOOOOO ....  AHHHHHHHHH  OLLLLAAAAAA   LOL

now all ya need is a big cap  to hold a lot of the good stuff .. and dump it to your motor ... 


crystal clear ?

now that is how the second stage of the cam flash board works ... see......  OK!  lol

now basically your motor is the neon that lites ... ok ...   notice how when you charge a cam board the neon lites when the cap is full it is the overflow portection  ....  : )

right ..... so now the darn neon stays litt a damm long time so long i can pull the battery from it put it in another charge it start it blinking and do it agin ... to another .. and the FIRST ONE IS STILL BLINKING ... 

o boy.... 

NOW ... ALL I NEED TO DO IS FLICK THE DAMM THING TO START THE 15 MIN BLINK AGIN ...

same thing ... 

now there is still much more to those simple cam flash boards .. bout another hole thred ... lol

but .. ill leave a bit for the kids to do .. : )

ist

[kooler]

The math is relatively simple, if you have a 2450mAh battery, then you have 2.45 amps or 2450 miliamps at your disposal for one hour.  Batteries, again, can be somewhat deceptive, as it may in fact be capable of supplying 3 or 4 amps over the life of a complete slow drain.

Sticking to the basics:  using 100mA your circuit will run for 24.5 hours it just a matter of turning mAh into mA.

thanks jadaro2600
that is what i was thinking.. thank you for your feed back..
so i got bored and i made a video.. and sorry for my cuss words.. i have cuss since i was 5 yrs old its hard to stop..
and drinking is hard to stop also..
i know my knowledge isn't up to date as you guys .. but here is what i got to share..

http://www.youtube.com/watch?v=oeAh9D7LkvE

i'll let you guys know when it goes out..
also i have a pulse motor to show you soon .. it impressed me so i hope it will you folks also..

robbie

[Mk1]

@all

For those that need a camera circuit and can't get one , at gold mine they are 99 cents ...

http://www.goldmine-elec-products.com/prodinfo.asp?number=G16329

Go fast before Ist buys them all.

[innovation_station]

here is a statement i will make ..

a cam board is a 2 freq time machine .. it is actually 3 freq ...  lol the 3rd is the kaboom...  inside the tube when you release the stored engery of the cap ...  it could be considered a potencial diffrance between 2 or more places ... : ) 

inside a sealed vaccume ... 

where run time is gained

W

[innovation_station]

@all

For those that need a camera circuit and can't get one , at gold mine they are 99 cents ...

http://www.goldmine-elec-products.com/prodinfo.asp?number=G16329

Go fast before Ist buys them all.

yea go spend your money fool ..

lol

i get mine free ... 

: P

they even come in a free bag from the store that they normally sell the bags ..... aswell i dont even need to check if they have any they will call me when there is a lot of 50 to pick up for free ... 

and your still a looser ... 

W