Joule Thief

[stprue]

While I wait for ist's video to load...
I will report the same kind of loss with the TRM that I had yesterday.
43v for one section
now I have finished another section
43v, so basically the same, but the 2 together only make 50v.
I will try again, but the I left the scope on earlier and the batteries ran down. so tomorrow will be the earliest to compare these data, but it looks like there is a funny thing here.

Now, if I could understand phase a bit more, maybe this is just phased not so well.
Maybe on a larger core where the frequency was lower to begin with I'd have more leeway with the base resistor.

Or, maybe there is another way to tune this.

Maybe there is something else like another inductor that could tune them together better...

I will try to get 4 quarters in the center, but maybe there is only room for 4 with fewer turns.

OK to ist's video. 3 transistors! wow ist.

jeanna

You may want to try to wind it regular and not in the MK way! I don't think this type of design is made for that type of design but I could be wrong.

[innovation_station]

im building the same thing i just did on the IST 5555  coil .. 

but with 3 1" toroides ..
the jt's are  12" cat 5 wire ..   6 turns ... 
i will not add the 50 turn generator windings or transformer winding just 1 feedback coil .. and 1 collector / accelerator winding ..

ill do 1 phase per toroide ...

ist!

here is 3 6 turn jt's on 3 toroides ..   i choose 6 turns .....and mk1 ... it has NOTHING TO DO WITH THE RESONANCE OF THE CORE MATERIAL!! 

maybe yours do but mine dont lol  tell me why !! 

cuz ill add the neos ... and that changes the CORE RESONANCE OF THE TOROIDE ...

so what have i got in my picture below ... ?

3 rotating magic feilds  about 3 diffrent toroides tied togather by magnets?

humm   

so now what i guess my 2.5 5 and 7.5 hz fit in this mess some where ..... 

but were still pissing around with flash lights ... 

so piss round with flashlights ...  lol  when you figure it out ...  who ya gonna come see... ?

thats right overunity!!

this is forced pulse rotation of magnetics by winding ... 

you all think ill rip a few FREE electrons off the magnets?   

FINALLY ....  MK1 CONTACT ME ASAP!

NO MORE FLASHLIGHTS FOR THIS BOY !!   

SO I JUST GOT A FONE CALL FROM 1 OF MY POTENCIAL  INVESTORS I HAVE DEMOED IN THE LAST YEAR TO ...



BOUT TIME THEY WOKE UP 

my last picture reminds me much about how your charakas   work lol  what my rocks and the staffs ... hummmm

[innovation_station]

what if i could do this from accelerating the spinnnnnnn in the toroide ... 

no im not saying i HAVE DONE THIS im saying WHAT IF I CAN DO THIS ....

and some inspration

crack the sky

ist!

now that i posted this

ILL post MY DESIGN THAT GOES RIGHT ALONG WITH IT ......   

round or square i dont care coil or no coil ... air core or ferroite magnetic ... 

all of it works on what i exposed and solved .. 

[stprue]

what if i could do this from accelerating the spinnnnnnn in the toroide ... 

no im not saying i HAVE DONE THIS im saying WHAT IF I CAN DO THIS ....

and some inspration

crack the sky

ist!

Not sure what you mean by this

[jeanna]

Hum, that is the reason i insisted on the diodes . Doesn't the scope show you that ...

Now you know that changing the pickup coil changes also the impedance and freq , i must insist again , the only logical way to determine the best design is to tune them to there maximum efficiency with the base resistor , that way you compare apple with apple . so connecting 2 pickup coil together will change the freq with a change of freq a change in voltage also happen ...

I just do not understand how you can say you know what is happening when all you can see is an amount of voltage in a capacitor???
Where is the diode that is teaching this to you?
I do not understand, I am sorry, but I just don't follow this.

Yes, the scope showed me, but the problem was:
My base resistor was too low and the transistor started to overheat.
It was at 0.5 ohm at the highest voltage.
It is too low and simply will kill the transistor.
Then the pulsing will stop.

BTW there is a definite polarity shown on the pickup. It is very strong. Almost nothing goes below the x axis on this.

So, with the tuner being the base resistor I must stop at zero ohm. And, I hope there is another way to tune this because I am out of room.

thank you,

jeanna