Overunity.com Archives is Temporarily on Read Mode Only!


Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
You also can visit us or register at my main site at:
Overunity Machines Forum



ENERGY AMPLIFICATION

Started by Tito L. Oracion, February 06, 2009, 01:45:08 AM

Previous topic - Next topic

0 Members and 14 Guests are viewing this topic.

Print
Go Down Pages 1 ... 880 881 882 883 884 ... 1776
User actions

Bruce_TPU

#4405
February 10, 2014, 10:52:16 PM
Quote from: totoalas on February 10, 2014, 10:23:01 PM


Hi Totoales,

i have MUCH respect for you and Grum and other REAL experimenters.

But please ignore open voltage.  Not saying it doesn't mean anything,  just saying you'll only know measuring across a resistor and using rms voltage on scope.  Or smooth to dc then resistor.

I am interested in the use of ground.  But again, measure across a resistor without ground, etc and the with and see if there is a difference.  If so, then you may be onto something.

Good job,

Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Magluvin

#4406
February 10, 2014, 11:30:44 PM
Above all, the fact that the out V is greater than the in V is the interesting part. it does seem to be a 1to1 ratio. And it is simple AC in AC out.  Now if it were pulsed or square in, then I wouldnt be so surprised. Makes me wana do 3 cores with 4 coils. lol  Hey, who woulda thunk that the voltage would have been greater with what Grum shows in winding ratios? I would expect V in to be V out if I had just seen the setup before seeing measurements. So what might more cores and coils do? ;D Would anyone expect a 1to1 ratio with 3 cores and 4 coils? Would anyone expect no more V out than Grum has shown with just 2 cores and 3 coils???? ;) Any explanations of why out V is greater than in V??

Mags

Tito L. Oracion

#4407
February 11, 2014, 12:16:27 AM
Quote from: Magluvin on February 10, 2014, 11:30:44 PM
Above all, the fact that the out V is greater than the in V is the interesting part. it does seem to be a 1to1 ratio. And it is simple AC in AC out.  Now if it were pulsed or square in, then I wouldnt be so surprised. Makes me wana do 3 cores with 4 coils. lol  Hey, who woulda thunk that the voltage would have been greater with what Grum shows in winding ratios? I would expect V in to be V out if I had just seen the setup before seeing measurements. So what might more cores and coils do? ;D Would anyone expect a 1to1 ratio with 3 cores and 4 coils? Would anyone expect no more V out than Grum has shown with just 2 cores and 3 coils? ??? ;) Any explanations of why out V is greater than in V??

Mags


Well, that is basic also, the V out is not only depending on turn but on type of core and how it was wound in the core. etc, and some other efficiencies to make the volts greater.  :D
and i believe that by adding magnet we can gain additional voltage.  :D

totoalas

#4408
February 11, 2014, 02:30:05 AM
Quote from: Tito L. Oracion on February 11, 2014, 12:16:27 AM

Well, that is basic also, the V out is not only depending on turn but on type of core and how it was wound in the core. etc, and some other efficiencies to make the volts greater.  :D
and i believe that by adding magnet we can gain additional voltage.  :D
Using magnet as spacer instead of paper in the center of my two e cores  proves ur point     oooooh   hhahhh   yun un 
I have a vintage scope and its just a matter of time before I can make a handle ot it  thanks Bruce

.96 milliwatt output  7 x 5 w  220 v ac load 100214  yt
Tito when can you show us ur   YT   link   
:) ;) :D ;D >:( :( :o 8) ??? ::) :P   TADO   RIP

Dave45

#4409
February 11, 2014, 07:06:15 AM
Quote from: a.king21 on February 10, 2014, 06:18:20 PM

Forest:  Do you have a link?
I think this is what Forest was referring too.

http://jnaudin.free.fr/html/tbfrenrg.htm
Print
Go Up Pages 1 ... 880 881 882 883 884 ... 1776
User actions