Overunity.com Archives is Temporarily on Read Mode Only!


Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
You also can visit us or register at my main site at:
Overunity Machines Forum



ENERGY AMPLIFICATION

Started by Tito L. Oracion, February 06, 2009, 01:45:08 AM

Previous topic - Next topic

0 Members and 13 Guests are viewing this topic.

Jeg

Quote from: stupify12 on April 13, 2014, 11:36:45 AM
If you dont mind could you show me some example circuit on what you just describe

Look two posts above. If you need 60hz then after the step down transformer use a half bridge rectifier.

Well now that I see it with more concentration in your case you have to put a smoothing cap so to keep the drain voltage just a little more than gate's drive voltage. The bigger the ripple that you have at 60 or 120hz the better. Just don't leave it going lower than your gate. 

If you don't know how to calculate the right smoothing cap, tell me the gate drive voltage and your drain voltage dc supply..

stupify12

Thank you very much Jeg  8)  I think I have already found the answer to this matter with your great help.  With this info I can now easily make plans for a HV 50hz/60hz Tesla Coil to discharge on my Receiving Transformer for easier Energy Extraction. I believe this what Kapanadze did he has made a  50hz Resonant Oscillating circuit to create a HV potential on the Secondary for Energy Transmission.   

TK did tell us on his 2004 video that the spark gap fires 50 times every 1 sec, That is all the info I needed to complete my device.  Remember TK also said that if you research Tesla Transformator you can easily debunk the set up of my device.

I believe I already told you about the Tesla Transformator which TK was referring to.   ;D ;D ;D


Meow    8)

Quote from: Jeg on April 13, 2014, 01:10:08 PM
Look two posts above. If you need 60hz then after the step down transformer use a half bridge rectifier.

Well now that I see it with more concentration in your case you have to put a smoothing cap so to keep the drain voltage just a little more than gate's drive voltage. The bigger the ripple that you have at 60 or 120hz the better. Just don't leave it going lower than your gate. 

If you don't know how to calculate the right smoothing cap, tell me the gate drive voltage and your drain voltage dc supply..

Jeg

I am very glad that it fits to your design. It is simple and quick.
Good luck on what you are doing, even you don't need my wishes...!  ;D

Dave45

Quote from: Google on April 13, 2014, 12:01:14 PM
Not so complex.  :o , you need to correct your direction. TPU has nothing to do with charge separation. Rest is your wish.  ;)
Its a logical approach, if you think the TPU and Kapandze are not energy amplification Id like to know what is.

And if I remember right Tito started this thread, no offense  ;)

later
dave

Its all charge separation 

Google

Quote from: Dave45 on April 13, 2014, 03:00:54 PM
Its a logical approach, if you think the TPU and Kapandze are not energy amplification Id like to know what is.

And if I remember right Tito started this thread, no offense  ;)

later
dave

Its all charge separation

Ok no problem, carry on. I will also contribute to the max I can but too many tangents. >:( >:( >:(
And please use language that all can understand. How will a coil create ion cloud ? How will a coil create charge separation. ?  >:( >:(

Kind regards.