Stanley Meyer Explained

[Vortex 22]

Thank you Sir for the nice answer !!
Regards
Vortex 22

[h20power]

Thank you Sir for the nice answer !!
Regards
Vortex 22

Your Welcome,


In one of my post on page 49 I give a summery of what's posted in this thread so folks can go right too the important parts and skip around all the drama. The waveform itself is the amp restriction that keeps amps from flowing through the water fuel capacitor, but without a differential probe one can't tune things correctly to get the waveform to be balanced having equal positive and negative voltages. You see the area under the curve represents current flow and when both positive and negative voltages are equal they cancel each other out so no current flows through the cell. That's why the water fuel capacitor can run for hours and the water never heats up. With mines I used a micro amp meters to take some readings and the amperage flowing through my wfc was only 0.6mA which isn't enough current to heat the water at all. The positive voltage was just five volts above the negative voltage when I took the amperage readings.
This part of the technology requires one to know how to use a oscilloscope and understand just what it is they are looking at on the scope mathematically. I think it's calculus level math but it can be solved just by simple subtraction of the area under the curve as shown in this video: [size=78%]https://www.youtube.com/watch?v=9q3Cw6dzSZ0&ab_channel=WeAreShowboat[/size]


This is how to solve this technology as to just what a balanced waveform is actually doing. Sure I went to college and took Calculus but it's not needed to solve this technology but what is needed is to understand just how to use a oscilloscope. These are work problems and it takes current to do the work of electrolysis and if the waveform cancels out all of the current no electrolysis is performed. This shows that with this technology voltage is actually doing the work to break the bonds of the water molecules.


Now in hindsight I think it is necessary to have taken Calculus and Upper level Physics as how would one know they were looking at a work problems otherwise? In the time I have been working on this technology I have run into a lot of people whom are very arrogant and stupid at the same time as that actual scope shot photo is from a person who swears he isn't pushing amps through the water fuel capacitor but the oscilloscope reading tells a different story. That's from Max Miller. The other one I have forgotten who posted it but again they were swearing up and down that they were not pushing amps through the water fuel capacitor but the oscilloscope reading tells a different story. This is the level of education I have had to deal with from others over the many years I have been working on this technology. As a lot, if not most, people that did get some of the needed equipment to read this technology never took the time to learn how to use it and/or didn't have enough education under their belt to know just what it was they were actually looking at.
If I were to take a reading of pure DC being used on the water fuel capacitor it would be a very boring reading just showing the voltage I am using and a straight line above the x-axis. All that energy under the curve in that reading would thus show unbroken current flowing through the water fuel capacitor. In most of the readings shown by others working on this technology they are showing broken positive current flowing through their water fuel capacitors as waveform that is being shown on their oscilloscope isn't lying, but they don't understand what they are looking at and were far to arrogant to admit their failings to others. Needless to say they didn't move forwards with this technology and eventually gave up, but not without putting up a fight towards me for attempting to telling how to actually read and interpret what their oscilloscopes were showing them. Since I understood what I was seeing when they posted their scope shots I knew how to ask the right question to show there were in fact pushing current through their cells as I'd ask them to take temperature readings over time as I knew the water would be heating up as that current shown on their very own scope shots was performing the world of normal electrolysis which heats up the water. Most of them refused to do so on camera and would even prevent others from pointing a laser temp reader at their cell while it was in operation.
Unlike them I allowed folks to take temperature readings of my cell while it was in operation as the cell would just follow the temps of the day as my waveform was balanced thus cancelling all of the current flow that would be flowing through the cell out. I remember Moray King making a note about how the cell's temperature was cold to the touch but he too didn't make the connection of just why the cell wasn't heating up while breaking the bonds of the water molecules at that time.


This is what set me apart from most people working on this technology as my education level was enough to allow me to understand what I was reading on the oscilloscope as I clearly saw a work problem which I had seen many times before in my physics and calculus classes.


Shalom Everyone,
Edward Mitchell
CEO and Owner
True Green Solutions
https://www.gofundme.com/f/energy-independence-for-you-and-me

[Vortex 22]

Hi Edward,

It's really nice to hear from you!!!

I Will try my best to study all materials, you have shared with us.

Many Thanks
Rgds
Vortex 22

[Vortex 22]

Hi,

Now, it's time to learn how to make a high voltage high frequency ac source VIC !!!

[h20power]

Hi,

Now, it's time to learn how to make a high voltage high frequency ac source VIC !!!

There are a lot of rules one must follow when making high voltage transformers. Here I am vacuum resin sealing the transformer: [size=78%]https://www.youtube.com/watch?v=i0gH4IX5r7g[/size] Now the reason for this is to get all the air out as the air will ionize and that ionization will work towards destroying the wire's protective coating. It also keeps the wires from moving around which will also destroy the wire's protective coating as they rub against each other as the transformer is in operation which is typically heard as a ringing sound. Then you must also choose a coating for the wire(s) that can withstand the voltages you will be subjecting them too.
Most of this I had to learn the hard way as even when I went to the Global Breakthrough Energy conference held in Boulder, Colorado, I put the transformers in some oil that was specifically designed for transformers. The problem with that was as though it did prevent the air from ionizing it did nothing for keeping the wires from rubbing together which again would cause the transformers to fail as once the wire's protective coating rubbed off the current will follow the path of least resistance and the current doesn't much care for going through any resistance wire and will go around if allowed to do so. So, instead of going from point A to point B and then point C on it's way to point Z the current will just go directly to point Z and bypass all the other points if allowed to do so. This you can see when you turn the lights off as you will see the blue glow of arching taking place within the transformer bobbins and you can also hear it.


Now it seems someone has went out of their way to make getting the materials needed to make these transformers a bit costly. Depending on which resistance wire you choose to use the cost of getting that wire is going to be on the high side along with the cost to get practically everything for the Voltage Intensifier Circuit. You see that circuit includes not only the transformer but all the other components as well, like the WFC, Blocking diode, and more. I just found out that the cost of the resin has jumped up to $280.00 per liter if you buy small amounts. Now if you can afford to get large amounts the cost isn't so bad but I'm talking more than $5, 500 to get a whole lot of the resin and its corresponding hardener. Everything from the transformer cores to the wire used has gone up in price and I haven't even started talking about getting the WFC made if you aren't planning on making your own.


I am not trying to discourage anyone from attempting to get this technology up and running but just giving everyone a heads up on what's the actual cost of things so that one can better plan for this endeavor. I did a lot of testing and observed the results of each test as I learned how to do things correctly. The first and second differential probes I got were the wrong voltage rating so I had to get a third with a voltage rating of 15kv. I think with some other parts of the technology I might have to get an even higher voltage rated differential probe than I have. If such an thing is required I have learned to just do it as I will not be able to move forwards if I don't. I have seen a lot of people try and buck the system and saw all of them that did so fail at getting this technology up and running as these rules can't be ignored or gone around they have to be followed and done. Anyone thinking that the laws of physics are just going to personally bend just for you will find out the hard way latter on it just doesn't work that way.


Meyer was a capitalist thus he really didn't want anyone following his work. We all need to be made aware of this as then you will start asking the correct questions when trying to solve this technology and not come in with your head full of Meyer's words some of which have no actual meaning in the real world. You have to do your own research making use of the scientific method as it must be figured out the hard way. I did a lot of this research and shared a great deal of what I found out about this technology to include the actual science this technology is mimicking in nature that allow it to break the bonds of the water molecules outside of Dr. Faraday's electrolysis method. Trust me when I say nothing on earth would be alive if they had to follow Dr. Faraday's electrolysis method to break the bonds of the water molecules.


One thing I have learned is this technology must move into mass production as that's the only way to get the cost of this technology down so that folks around the world can afford to own and have it. This is something Meyer, Dr. Dingle, and a few other also knew. Whomever came up with the idea of blocking and/or never giving their support to anyone who tries to profit from this technology is a true enemy of this technology and wishing things to go on like they are right now forever as that statement is for the current fossil fuel run system to keep on going with no end in sight.
Anyone thinking that this is a easy technology to make and can then be just made by anyone with a set of plans in their hands are just lying to themselves as they leave out all whom are abjectly poor, disabled physically or mentally, the elderly, and the young, plus those that find themselves to be all thumbs when it comes to building anything. I didn't make up the rules of the markets as those things were put in place long before I was born and thus like everyone else I too must follow them.


I feel with all my heart this will be the year this technology finally makes it to the marketplace.
Shabbat Shalom Everyone,
Edward Mitchell
CEO and Owner
True Green Solutions
https://www.gofundme.com/f/energy-independence-for-you-and-me