Howard Johnson Replication Tube Claim

[TinselKoala]

YouTube says "This video is unavailable.".

Uh-oh. Suppression.
Or maybe YT just isn't finished processing it. I'll ftp you the high-res original (for free!!) if you give me your ftp login particulars.

[CLaNZeR]

But you see here is the dilema. The string has to be tight enough to start and increase but loose enough to de-clutch all while the string is invisible enough to not be seen, and actionable from some 6-10 feet away by a motor shaft that is 2 inches long and held in place by a pillow. This sounds like a Steven Spielberg thriller called The Magic String Theory.

Then is the dilemma when Mylows assembles and starts the wheel while having that motor on turning a string that is not attached or de-clutched, hence no string tension on the motor shaft side, then placing in on the wheel base to show it turns. MMMMMM. Nahhhhhh.

We have to remember that this disk is spinning at very very low revolutions, even though the disk may look like it is going some speed, it actually is not. Look at my wind down videos and see even at 40 RPMS how fast the disk looks like it is going.

At slow RPMs on the motor, you could easly motor side tension the incoming line, double wrap and tension the out going line, You can slacken off that loop of Cat Gut and it will happily loop.
Or even better just have a small switch next too your side that you can turn the motor off when the line is too slack, once verything is in place, flick the switch and get the tension right. There are many ways of doing it, that do not need any real technical expertise.

Get some Cat Gut, tie it in a knot and pull hard, it will hold damm good. Now to un do the knot simply push on one end and the knot will slide away very easly. Fantastic material for a clutch. Try that with string, different story.

Like I say keep an open mind and accept every possibility.

Please do not make me replicate this, because you know I will LOL 

[AquariuZ]

@all, you are being violently misdirected towards the last (faked) project. It is so obvious it is almost ludicrous. (Yeah just as ludicrous as my CT  )

There is no doubt in my mind whatsover that this setup is genuine:

http://www.youtube.com/watch?v=hpQA5c9guvE&feature=channel_page

The reasons should be obvious from my other posts.

Do not be fooled & do not trust anyone, including myself, but rather replicate the above as close as you can and see for yourself.

Nuff said.

AZ

[Pirate88179]

@ Pirate: The idea of apologizing to you is absurd and demeaning, nor would i ever apologize for, or be intimidated out of, sticking up for an unconcerned person who was attacked by a cyber-bully.

You were certainly in the wrong to suggest anything like that about the father of an opponent, and then you compounded it by deriding him publicly: Of that there really is no question or excuse.... And in virtually any other forum we could name, it would have gotten you banned, for at least a time.

Hiding behind a cheap disclaimer like some lawyer, while still mouthing the poison, is not an "excuse" but more like an insult to our intelligence.

It is apparently hopeless to expect you to apologize for it. But it is not yet hopeless that this forum will collectively reject, and punish, such behavior in the future.

jibbguy:

I already accepted your apology, there is no need to keep doing it, although I do appreciate your going out of your way to do so.

Your statements quoted below in bold:

"You were certainly in the wrong to suggest anything like that about the father of an opponent, and then you compounded it by deriding him publicly: Of that there really is no question or excuse.... And in virtually any other forum we could name, it would have gotten you banned, for at least a time."

I did not, nor have not, suggested anything about anyone.  I asked a question.  Even after asking this question, I added in parentheses that "I am just asking I have no idea".  How you think a question suggests anything about any one is beyond me.  Most people I know ask questions in the hopes of getting information.  My opponent?  I have no opponents that I am aware of.  Again, I have to admit to not having any idea of what you are talking about here.

"Hiding behind a cheap disclaimer like some lawyer, while still mouthing the poison, is not an "excuse" but more like an insult to our intelligence."

You forget, that "cheap disclaimer" was added later for your benefit after you explained to me that you totally misinterpreted my words.  I also find it highly insulting that on a public forum, you compare me to an attorney.  I can't think of anything to lower say about someone.

"nor would i ever apologize for, or be intimidated out of, sticking up for an unconcerned person who was attacked by a cyber-bully."

This was part of your opening statement.  [/]Who were you sticking up for here?  And who is the cyber-bully you refer to here?  This is funny. On a public forum you have defamed me in the process of accusing me of doing something I clearly did not do.  Reminds me of a mother who hits her kid and tells him not to hit people because hitting is wrong.

If you are concerned about my statements about Sterling's terrible and misrepresented reporting of the Mylow situation, perhaps you should read them again too.  Seems as though I was correct given that it appears that John Bedini may have a libel suit against him.  My guess is that there will be others as well.

I hope this clarifies this situation.  I have had no problems with you until you accused me of doing something I did not do, and then attacked me again, also for something I did not do.  Since it appears you may have trouble reading, I typed this very slowly for you.  I hope it helps.

BIll

[broli]

@all, you are being violently misdirected towards the last (faked) project. It is so obvious it is almost ludicrous. (Yeah just as ludicrous as my CT  )

There is no doubt in my mind whatsover that this setup is genuine:

http://www.youtube.com/watch?v=hpQA5c9guvE&feature=channel_page

The reasons should be obvious from my other posts.

Do not be fooled & do not trust anyone, including myself, but rather replicate the above as close as you can and see for yourself.

Nuff said.

AZ

Using the recent aluminum phenomena I think that would have the most effect of it. Look how close the stator magnet is to the spinning disk and vice versa to the rotor magnets on both sides.