Howard Johnson Replication Tube Claim

[billmehess]

From that great epic movie "Gone With The Spin" I now cry out:

                    "As God is my witness I'll never be Mylowed again!"

                                     ( Until next time)

[jibbguy]

@Waynegage

Thomas Valone PHD, former patent office employee, has stated on the record that there have been over 3,000 Patent Requests "secretized", many of them "free energy" related.

And there is the patent from the inventor Vijak K. Chandhok, “Method for producing through extrusion an anisotropic magnet with high energy product”, U.S. Patent No. 6,787,083 ; most recently re-issued on Sep. 7, 2004.

This one has been under the control of the U.S. Department of Energy for about 8 years now (and sat on of course); apparently they got ahold of it because they had given the guy a Grant. It is reported to allow the cheap manufacture of "asymmetrical" magnets where one pole is significantly more powerful than the other.

Such a thing could make this entire thread moot within a very short time... If they ever do anything with it.   

As for your specific request, perhaps that "secret" part and the "court order to remain silent" part might make it a little difficult for the people whom this has happened to in the past, to state so publicly? Maybe you can think of a way around this, so we can provide such proof to you? I have actually been looking for such a dodge for a while now... Because some people might like to go public with their story if they could get away with it without being imprisoned.

With corporate shelving (which is much easier to find proofs of), "Court Subpoenas" can work for this, because no Non-Disclosure Agreement can trump the requirement to testify under Oath in a Court of Law; and even the corporate employees must testify or face Perjury charges if they lie for their bosses. But with these Federal orders, a person can only testify before Congress (ask "Sibel Edmonds" about that one, lol). So i honestly am open to suggestions on defeating this.

This "secretization" technique was also reportedly attempted on a few peeps who avoided it, such as Stanley Meyer himself. He avoided this fate by the fact that he had already filed internationally and had mailed material overseas (lol a good thing for inventors here to remember!!), and so it was too late for them to "secretize", the cat was already out of the bag. They were reportedly very pissed off with him over this at the Pentagon (people like that are used to getting their way). That also came from Dr. Valone's public statements.

Anyone see any "motive" there for killing Stanley Meyer then (i mean besides just "making gasoline obsolete" hehehe)....? Hey, it's a possibility, after all... Just somethin' to think about

________________________

And no Runningbare, the idea of "Secretization" is to "declare them secret"... This then supposes that they were not "secret" before hand; otherwise it would be more along the lines of "re-classification" verses "classification".

Although inventors who do not embrace Open Source are often pretty "secretive" themselves... And in these cases that attitude doesn't help much and only makes it easier to take it away from them

________________________________________

The Open Source model also is worthy for inventors to embrace in that it takes away the "secret" and "mystical" aspects; and will give them creditability as they earn it.

This past affair DID NOT follow the Open Source model... The very first requirement is "verification"... BEFORE replication attempts occur. 

[joe_1001101]

Morning people,

Joe, try this one on your Apple monitor:

http://www.youtube.com/watch?v=hpQA5c9guvE&fmt=18

Video #6:
It LOOKS like the acceleration cannot have been by hand from LR graph and TK experience with his disc. Correct me (again) if I misinterpreted your last posts on this.

It LOOKS to me that there is no fishing line either. In THIS specific video.

Maybe you can take a look because confusion is taking over.

Again: two setups
1) Original with channel magnets and black stator with the stator close to the disc (key)
NOT the 41a/b setup with the red stator (not near the disc)
2) Later type with bar magnets and two red stators (fakes)

I believe everything after 41a was faked, not only because of the footage of the devices and the later clear fake setups, but ALSO Mylows behaviour changed very notably beginning with 41b.

For those who wish to verify this for themselves, LISTEN carefully too.

I am extremely grateful for LightRider having made a backup of all the videos on his channel.

http://www.youtube.com/profile?user=LRCan1&view=videos&start=80

Any video you wish to see in HD please add &fmt=18 to the end of each individual video.

AZ

AZ,

It would be hard to see fishing line with out looking at the original hi-res video (or copy).  I do not have a copy of the hi-res video #6.

But anyway, I think the bottom line is not to trust any self-running devices as being real, until verified. 

So, I hope we have learned our lesson from the fishing line videos:)

Thanks,
Joe

[Pirate88179]

Hey:

Stefan should make up T-shirts that have a picture of a bunch of magnets on a wheel and a caption that says:

I Got Mylowed On Overnity.com

He could make them available in the OU store and some of the proceeds could go to the OU prize fund.  This would be an honest way to add some humor and to raise some money.  I know I would buy one or two.

Wouldn't it be some poetic justice if Stefan made more money on T-shirt sales than Sterling did on the sale of the plans?  I could really get behind something like this.

Stefan, one of my neighbors is in the T-shirt business and we could get a great deal.  (I don't want anything out of it)  Someone here can come up with some designs and this guy can scan them in his computer and make them up.  Or you can get a good deal on the internet as well.

This might be a good idea.

Bill

[LightRider]

A little help would be appreciated...
I mess up something...
now, i can't see post image anymore, I just see:

sale.jpg (51.33 KB, 621x398 - viewed 220 times.)

and if i click it i get the error page:

An Error Has Occurred!
You do not have permission to approve items.

Thanks,
LightRider

(Sorry to be off topic)


EDIT:

... I went back several pages and all the pics are gone and they say An Error Has Occurred!
You do not have permission to approve items.

Same here...