The Master Of Magnetics "Steven Mark"

[mrd10]

MRD10

Take the OP connections and connect it too  IP1, do the same with bifilar coil 2 or 3, wire a OP2 over them and connect it to IP2,  could this then beself sustaining, when magnets are added ? ? ? ? ?

For an out put take one connection of IP1 and IP2,

WILD WILD GUESSS ! ! ! ! !

Virus

Hi Virus,

The best thing would be to wind some coils and experiment, who really knows.
We are all here trying to figure things out. There's a Guy in this forum, that were anxiously awaiting his results, as he has said he has wired his tPU as per Teslas transformer on patent 390 721, and that he didnt have any input connected to it and the compass he placed in the middle of it was slowly spinning,  but he wont post until monday.

What I did was draw the transformer windings out.
My God child came over yesterday, as he comes to visit me from time to time and loves what i do. He is a smart cookie as well, and mentioned to me to look up Tesla's egg on youtube, and i noticed the connections were 4 as per that transformer.

This transformer setup causes a rotational magnetic field, now it's quite possible that SM is tapping into some resonant frequency, like earths magnetic field, and is inducing this into the transformer setup, he mentions small kicks building to larger kicks, so its quite possible that this transformer Toroid configuration causes this effect.

Dave did do an experiment with 3 non-toroidal transformers, where if he inserted 2 exact sinwaves (in exact phase) into 2 of them and fed this to a 3rd transformer, the signal would double, so its quite possible with a toroidal unit something like this would exponentially climb.
SM did say that toroidal is a fascinating configuration, and crazy phenomenon happens.

I've been quite active in this forum, as i think this is one of the best things since sliced bread.

Dom

[mrd10]

Dom, are you in London?

Just a quick note, from the video we can now show that we have a thick collector at 90 degrees on the inside.  Around this we have an external vertically wound coil which goes right around the entire thing.  Then when the tape has been removed at the back, we can see a big empty area inside.  So I guess for now this can show that the inner coils are indeed wound in sections around it, not as one hole coil around it like the outer one which we can see its shape in the back tape.

So far this confirms mostly everything we had via Mannix.



Dave.

Hi Dave,

No Im in Australia, its 10 oclock now, night time.
I catch up usually at night on this forum. Yes the larger one don't have much in them, If you look at the good quality mp4 video, on the smaller ones, youll notice to that these are emtpy rings, I could tell, even with the tape on them, freeze on the 6 inch one and youll notice that there is wires wound on the top, but if you look about 10cm down, its a different shade of black, looks like there is nothing there, think of the first two prototypes and then think about winding them with tape.
You wouldn't know really would you.

But luckily i guess those first two don't have much on them, and then when we see the larger one being cut, they look empty as well, so really these devices have to rings.

The second prototype is interesting, because all the windings are on the bottom ring, but i guess by making them smaller then he could do the same on two rings.

Dom

[virus]

Guy's

I got all this together, suppose it is not worth starting without a o-scope only have a DMM.

I need to get an o-scope, any suggestions, what must I look for, what must it can do, etc.

Virus

[mrd10]

Sure and I tell em to start a bomb fire.....lol....only kidding, I did wire my mums hot plate today, and was careful by tirning the power off before starting.

Hiya Lindsay, Who are the 3 your referring to?  Last night the magnificent 7 were on, but i think they should rename it to the dead 7, since i think they are all dead, I'm hoping we don't all die before we findout....lol

Any comments from SM's? has he or you been corresponding? does he still see what us crazies are doing here?

HIs prob having a laugh and going.....no no no, thats not it......ah bugger em, i'll keep em in suspense......lol

Sincerely,

Dom

Oh one thing that has been bugging me, is how does the magnet work? would it cause oscillation if you just placed it ne
ar a small inductor toroid?

[mrd10]

Ok Lindsay, in saying that, I ve worked with 240, thats here of course in australia.

If we were to have safe gaurds set out before continuing, would that suffice, like a disclaimer

so here it goes.:-

The information provided on this site is believed to be accurate, but is not guaranteed to be free from errors. The information is provided "as is" - use at your own risk.

Several projects involve direct contact with mains electricity. You will be exposed to dangerous voltages, as well as potentially causing damage. Do not attempt these things unless you are aware of the risks.

I can not be held responsible for any consequences or outcomes after visiting this site.

END

Hows that sound

Sincerely

Dom