Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

[cheappower2012]

@a.king21,
from the picture it looks like hes used a spark plug for a spark gap
no ground as I said before doesn't need it to work.Is the high voltage dc or ac
my belief is it doesn't matter in this device,I see a lot of crap
the bunches of electronic parts mostlikely does nothing.Did you get more pictures,
and what other things can you tell us.

[captainkt]

@Jack Noskills, I will try build sliding ferrite to tune, try to get transfer to output coil of the energy that heats a screwdriver that is pushed through  a hole in centre of pancake. As my set up is at the moment the screw driver heats but does not alter out put at all. A steel plate works best followed by copper to get auto start on hob to work, once working the plate can be removed providing there is enough load the hobs keeps going. Experimenting takes a lot of time because as soon as I alter wire length or load in any way heater drops out and I have to start it up again.
Regards
Keith

[Jack Noskills]

Thanks for the update. If you connect two coils in your pancake as shown in the thread I posted previously, then you can tune it using ferrite without load. Once set, resonance stays and your screw driver will not heat up anymore whether you use load or not.

[mike140366]

Ladies and Gentlemen,
I am the sponsor and visitor, that went to see TK's invention, on 2 occasions.
My first trip, with a physicist (bilingual in Georgian and English), was on the 5th to 8th May 2012.
We met TK, his son and twin brothers, who build these devises. TK builds the important parts.
I'm the guy in the blue shirt, holding the box. The plastic box weighed about 6-8 kilos and was shown to run a 2 kw fire (2 bar) for about 4 hours. I paid TK, via a friend of the physicist, 3000 USD. This payment was ongoing, as TK was in bad health. I also, via the friend, paid for TK's medical treatment. All was well and good. The devise seemed to work without wires attached (except the earth). I picked up the box, looked underneath, followed the braided earth lead outside to an earth spike (for grounding), touched it and checked it for hidden wires. We agreed to sponsor TK, to pay for and build a 10 kw 3 phase version, that could be tested, using multi-meters etc. In the meantime, I approached 2 government agencies and started visa applications and commercial negotiations.
The return trip, with an RF Electronics expert and a box of test equipment (list below), was arranged for 26 July until 02 August. I had a Confidentiality Agreement ready and a Technology Licence contract. I emailed these legals to TK's lawyer, beforehand. On day 2 of the trip, I met with TK's lawyer, made slight amends with him to the 2 documents, printed off and signed the Confidentiality Agreement. The Technology Licence was to be signed after the tests were carried out. I had done my part, as agreed. TK, at this point, stated that he was worried about our test procedures. I emailed his lawyer and stated "I have asked *** to test the machine, to clarify what goes into the box and what comes out of the box. This will not be invasive testing. These tests are to prove that there is no outside source of energy and that the energy output is of good quality. Each test will be approved by TK before we carry them out. We have rented electrical test equipment to do this: Neotronics Impact Gas Detector. Fluke 435 Power Analyser. Fluke 199 Scopemeter. Radiodetection CAT and Genny. Monitran VM110. Flir i60. Mechanical stethoscope. Basic clampmeter. All these machines have standard data logging, to save the results. We shall take the process of testing very slowly, confirming with TK at every stage. If we cannot test, we cannot get our government to invest in a manufacturing company, or sell the power to industry."
We then waited a further 2 days. In the evening of day five, TK's son came over and showed us a picture of the (supposed) 3 phase machine on his digital camera (a 2" x 1" photo). We said thank you but stated that testing must take place for this working arrangement to proceed. We asked for a full day of testing and we only had 1 day left. Nothing until 7pm of the last evening before we flew out. During the previous 5 days, we had promises from TK that all is well and we could test that day. Each day we saw nothing. At 7pm, we were invited by TK to see the box running. We asked if we could test. He said no. We politely declined his offer. He called us repeatedly over the next few hours, to try to get us to see his box. To us, as commercial people, this was just TK trying to reel us back in, as a big fish that is getting off the hook. The last contact, by email, from his lawyer, stating that they believed that this test equipment would find TK's secret. He also stated that we should risk some more money with TK, for a further 2 months. By the way, his lawyer amended the Technology Licence to state that I would pay him 1500 USD a month....
That said it all. We left Tbilisi at 3am the following morning and went to the airport. Who did we see there? TK's son, in the arrivals section. Probably waiting to receive a new party, to look at the machine that I had paid for.
Total spend on the project was about 20,000 USD.
I am a committed Christian. TK said that this was a gift from God. I prayed with the man. He rewards me with insults, saying that I was trying to steal his technology. TK, unfortunately, in my opinion, lives in fear. His trust is verbal only. He gets financial reward and runs away. When he was seriously ill, we paid for a doctor to see him and give him life saving medicine. This means nothing to him.

[verpies]

This device was rated at 2kw and ran for 4 and a half hours before the team left the premises. The device powered a 2 kw electric fire to full heat.

According to this, 9kWh of energy was dissipated as heat in the heater's resistive filaments.

Using the state of the art batteries, this feat would require 7.5 Litres of space (weighing 18kg).
If there was not that much space to hide the batteries (including the heater enclosure!) then chemical batteries could not have been used in that demo.

Conventionally, that leaves fuel cells as a plausible but very difficult to accomplish energy source and low frequency Near Field magnetic induction (LF air core transformer).

Converting a whole room to an air core transformer makes sense economically when each demonstration brings at least $1000.
Did anybody think to take the aquarium device outdoors - away from eventual windings in the walls or under the floor/ceiling ?