Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

Ð¡ÐµÑ€Ð³ÐµÐ¹ Ð’. · September 19, 2012, 01:43:54 AM

to wattsup hunt

Ð¡ÐµÑ€Ð³ÐµÐ¹ Ð’. · September 19, 2012, 01:56:31 AM

You will need this tool for Nano Pulses !! Complete schematic of Very High Voltage - Very High Frequency - Very Broadband - Oscillograph probe designed specially for HV Nano Pulses !!

This is capacitive probe with High Voltage 30,000 volts AC and divider 1000:1.

Zeitmaschine · September 19, 2012, 07:20:09 AM

Quote from: jbignes5 on September 18, 2012, 11:35:43 PM
Has everyone gone bananas? The first thing is that the video is already poor quality and then to boot you go through the compression of youtube which also messes with the frame rates and quality further. You have proved nothing in your assumptions absolutely nothing.

What has the frame rate of the video to do with the readings of the ammeter which are clearly visible?

In fact during the second run there is a transformer (in a black box below the table) connected in parallel in ADDITION to the lamps which loads the car battery (back loop). But instead of drawing higher amps the amps consumed by the device go even down. Strangely also the amps at the output. During the second run (back loop) the meter shows 24.0 amps (at 21:26), during the first run (without back loop) it shows 25.1 amps (at 18:22). Could this mean that the interaction with the additional inductance of the back loop transformer makes the device supply less amps?

Maybe Kapanadze could provide us kindly with a higher res video inclusive translation.

Quote from: wattsup on September 18, 2012, 11:48:54 PM
My 2004 video only goes up to 14:16 so I don't know where you got video up to the 17:?? mark.

The link is in my post. http://www.youtube.com/watch?v=r99g4mjEvTE

Regards

wattsup · September 19, 2012, 08:56:38 AM

Quote from: Zeitmaschine on September 19, 2012, 07:20:09 AM
What has the frame rate of the video to do with the readings of the ammeter which are clearly visible?

In fact during the second run there is a transformer (in a black box below the table) connected in parallel in ADDITION to the lamps which loads the car battery (back loop). But instead of drawing higher amps the amps consumed by the device go even down. Strangely also the amps at the output. During the second run (back loop) the meter shows 24.0 amps (at 21:26), during the first run (without back loop) it shows 25.1 amps (at 18:22). Could this mean that the interaction with the additional inductance of the back loop transformer makes the device supply less amps?
Maybe Kapanadze could provide us kindly with a higher res video inclusive translation.
The link is in my post. http://www.youtube.com/watch?v=r99g4mjEvTE
Regards

@Zeitmaschine

Thanks for the link. I don't know why but I tried downloading the video with my Naevius converter but it says there is an error although I can see it on youtube.

The black transformer output is connected to the battery so it is feeding back some or all of the battery expended energy back to the battery. Again I will have to look closer at this tonight.

@Ð¡ÐµÑ€Ð³ÐµÐ¹ Ð'.

Thank you very much for that great web site. The dual transformer you show is close but we need to find the exact triple model.

I am putting up a close up of the triple transformer model number that is in russian.
Can you please type the model number in a post so we can copy and paste the russian characters to do a direct search.

@all

Also I am putting up again the ohms values given by @Bernhard. Can any EEer look at these values and try to extrapolate any comparable input to output values of step up ratios. This would be the minimal info required if we cannot find the exact model spec.

wattsup

PS: Let's just get back to work on the TK devices but of course we need to work together with thanks.

jbignes5 · September 19, 2012, 10:13:03 AM

I do apologize for my response but lets try to figure this out instead of just assuming it's a fraud.

Let me show you a credible replication.

[size=78%]http://www.youtube.com/watch?feature=endscreen&NR=1&v=atlnVNy0IDE[/size]

Very nice replication at that. And like I have said before it is a ground loop method. As explained in this video.

Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

Ð¡ÐµÑ€Ð³ÐµÐ¹ Ð’.

Ð¡ÐµÑ€Ð³ÐµÐ¹ Ð’.

Zeitmaschine

wattsup

jbignes5