Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze

[verpies]

Regarding the recent posts of TK's disc machine. I have at my disposal.......... One sheet Brass 3 feet X 4 feet at 0.6mm thick. One sheet Copper 3 feet by 6 feet at 1.5 mm.
Now I am willing to make the "ultimate" sacrifice and carve them up for the advancement of science. 

I recommend waiting a while with those precious materials of yours and continue with your current setup until you exhaust all the possibilities for improvement.

To duplicate the Kapanadze Motor, in addition to the driver electronics you'd need a fiberglass rod for shaft with bearings, a stack of ferrite magnet rings on this shaft and an iron sheet for flux guiding disks .  That's a lot of work and materials you probably don't have.

[NickZ]

   Dally replication, same guy.  Look again, through newly opened eyes...
http://www.youtube.com/watch?v=p0S0EgLcnWA


  @Tectron:  I have no problem viewing the Russian version: Although no minute 9:45 to be found. 
   http://www.youtube.com/watch?v=_e3RpsEZE14
 

  Hoppy:  I will check for the wire, but I think that you are barking up the wrong tree, again.  I know it is much easier to look for fraud, than to replicate. But, I will not assume that something is fake, first. Don't you think, that if there was a wire there he would not be showing it? 
  In any case, we need to get a hold of this guy, and ask him to hold the device in the air, move it around, or whatever would suit the skeptics. Now that we have a bird in the hand.
  If this were another fake, the two 250 watt bulbs would not dim considerably on a grid source, when the third 500 watt bulb is added. At least not as much, as can be clearly seen.
So, please, lets not throw water on the fire, just yet. Please!

  EDIT:  Hoppy, there is no minute 9:45 in the original Russian video,  only 8 + or so.
So, where are you seeing this wire hidden in the concrete slab?

[cheappower2012]

You cannot see at near the bottom of the coil,no need for a big coil form,except to hid something,a battery could be hidden
easily,you can get very small,very flat, very ,powerful batteries these days,the person making the video,
did not show the wattage of the bulbs,
its hes word there 250 watts and 500 watts.We don't know what
frequency is applied to the light bulbs,hes word its low frequency,
I don't buy low frequency.If you compare the TK device 2004 video,we know that the output
is around 50hz/60hz he feeds the output to a standard step-down transformer connected to a bridge rectifier to complete
a feedback loop.In this device the step down transformer is air core,which is highly inefficient
at low frequencies.He says that the bridge rectifier was getting real hot if you use a standard rectifier
with a switching speed thats too low you will cause it to heat up and burn out ,frequency has to be above 1,000 Hz.
.With high frequencies you can light up bulbs
with much less power ,it creates an illusion that your outputting much greater power.
How hes driving the yoke indicates a much greater frequency than
line.
I agree with Hoopy on this one its highly suspicious!

[T-1000]

Looks like this thread is still chasing goose in the wilds..

And apparently nobody wants to sit down and actually assemble and try to understand something like this:
http://www.youtube.com/watch?v=Sbb_kSgvzoo
http://www.youtube.com/watch?v=ZRfWTlbFy1k
http://www.youtube.com/watch?v=5w9nJahkFB0
http://www.youtube.com/watch?v=rM5XSc_HxTk
http://www.youtube.com/watch?v=ZCIjkfWESs0
http://www.youtube.com/watch?v=7C4yEAm2ue4

When you get your hands dirty on this stuff while actually assembling and tuning devices the entire TK thread goes into past like bad dream...

[NickZ]

  My hands are dirty, are yours?  And it's not from chasing wild geese...

  Can't understand a word of those videos, is that an example of what?  Hidden wires?

  Why don't you just show us your working device, or is it a secret, also.
 
   Back to looking for those wild geese. Gotta eat...