Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



IST'S FURNACE FAN PULSE MOTOR SELF RUNNING NO INPUT BATTERY

Started by innovation_station, September 04, 2009, 08:53:09 AM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages 1 2 3 4 5 ... 7
User actions

innovation_station

#10
September 09, 2009, 08:07:22 AM
now i have showen the BIG ROTORS IM BUILDING ...

next im going to show

for the smaller rotors  the motor caseing i have built from an old wire spool

this unit is for my furnace fan motor i hope to finish the motor caseing today ...

i have almost all the required parts gathered up and ready to assemble ..

im happy with the way it turned out it is simple and looks darn kool and easy to adjust and assemble ..

ill add some picture of all the parts i used to make the caseing..

it is a 30" there bouts wire spool  it had 3 bolts holding it togather it had wood slats in the center ..

i then used a card board tube from the big spools i had to redrill the connecting bolts ..

not much to it ....

ist!

here is a picture of a wire spool i will use for a motor caseing ..
and here is the cardboard tube .. i will use for the caseing ...

this spool showen is not the exact same as i have already used ... this one has 4 bolts...
To understand the action of the local condenser E in fig.2 let a single discharge be first considered. the discharge has 2 paths offered~~ one to the condenser E the other through the part L of the working circuit C. The part L  however  by virtue of its self induction  offers a strong opposition to such a sudden discharge  wile the condenser on the other hand offers no such opposition ......TESLA..

THE !STORE IS UP AND RUNNING ...  WE ARE TAKEING ORDERS ..  NOW ..   ISTEAM.CA   AND WE CAN AND WILL BUILD CUSTOM COILS ...  OF   LARGER  OUTPUT ...

CAN YOU SAY GOOD BYE TO YESTERDAY?!?!?!?!

SkyWatcher123

#11
September 10, 2009, 02:00:24 AM
Hi folks, Hi IST, you know I remember reading an article which may have been on Bedinis site or somewhere where a guy used a large heavy, round, wooden kitchen table top for a flywheel and it was powered by a 12 or 24 volt dc motor and 1 or 2 permanent magnet generators recharging a couple lead acids and all were connected by a belt and it was said this may have been self running. So maybe it is true after all that one can tap enough energy from a large enough flywheel to become self sustaining. Also another story of a test that showed a flywheel that required say as an example 100 watts to rotate up to a certain speed, then after a given length of rotation time is stopped and then started up again, it now only requires say 10 watts to rotate to same certain speed, although if you wait too long to rotate it up again the lower input effect is gone. This seems to suggest an effect like spinning water in a glass and it keeps spinning for a time, only in this case it must be the aether spinning or whatever we want to call what the flywheel is affecting in the space it sits. I think your motor has good possibilities.
peace love light
Tyson :)

innovation_station

#12
September 13, 2009, 08:06:46 AM
i have been working away on both thease units ...

ill add some more pictures today..

ist

To understand the action of the local condenser E in fig.2 let a single discharge be first considered. the discharge has 2 paths offered~~ one to the condenser E the other through the part L of the working circuit C. The part L  however  by virtue of its self induction  offers a strong opposition to such a sudden discharge  wile the condenser on the other hand offers no such opposition ......TESLA..

THE !STORE IS UP AND RUNNING ...  WE ARE TAKEING ORDERS ..  NOW ..   ISTEAM.CA   AND WE CAN AND WILL BUILD CUSTOM COILS ...  OF   LARGER  OUTPUT ...

CAN YOU SAY GOOD BYE TO YESTERDAY?!?!?!?!

innovation_station

#13
September 17, 2009, 08:59:29 AM
well i picked up a few more truck loads of spools ...  ;D

so ill get it built sooner than later

also i removed the rotor from the 30 hp induction motor what a job ... i had to grind it off it took me 3 days ... but i got it off

i have since picked up about 30 more spools .. some are quite large ... over 5 feet ..

here is a picture ..

ist!
To understand the action of the local condenser E in fig.2 let a single discharge be first considered. the discharge has 2 paths offered~~ one to the condenser E the other through the part L of the working circuit C. The part L  however  by virtue of its self induction  offers a strong opposition to such a sudden discharge  wile the condenser on the other hand offers no such opposition ......TESLA..

THE !STORE IS UP AND RUNNING ...  WE ARE TAKEING ORDERS ..  NOW ..   ISTEAM.CA   AND WE CAN AND WILL BUILD CUSTOM COILS ...  OF   LARGER  OUTPUT ...

CAN YOU SAY GOOD BYE TO YESTERDAY?!?!?!?!

MrMag

#14
September 29, 2009, 02:36:37 AM
Well, I guess IST got his time machine up and running. :)
Print
Go Up Pages 1 2 3 4 5 ... 7
User actions