Second Stage Joule Thief Circuits

[gadgetmall]

@gadgetmall,

I did try to design the circuit to meet your requirements.

>>can this be adjustable ? or is it already ?

Yes, you can adjust the two pots. One for the charge dump voltage level and
one for the feed back charge dump to run battery.

>>Couldnt we just use for now a mosfet or scr controlled by a 555 timer timed to
>>trigger the ,mosfet /scr for a few seconds or is this not possible without
>>programming like a pic or something ?

If we use too many pats then you will use up all the o/u you get. I have tried to
design the circuit to use no current at all when inactive.

The circuit may need some "tweaking" and change of resistor values to
get it to work. When (if) it works then I can update the circuit drawings and make
some pcbs for this project.

Alex.

thank you Alex for getting evolved and taking the time to contribute to the prize project  . I am not sterring you wrong . i promise . this isnt like anything i have seen every . I will get a proto solder board from the shack tomorrow and start on the pats that i have while i order several sets of all the required pieces . Many many thank yous ..

@pony . ? I appreciate you comments but i have enough now and i am going to win this . 100% positive . yes that's bold  so you better know i mean business . I wont argue anymore with you . it don't matter whether  the charge cap has 0 volts (which the never do) or half a volt . it will go ou either way . .500 volts is where they normally sit around here as they stop working  silicon hence .5 is where i will start My next repete of the  same Experiment 1 and 2 . today !! and as far as measurements i did all that is needed before . I will log it this time  on paper and video .i'll borrow someones high speed to upload it but its pointless doing that because there is always some one somewhere that says is a fake and its no ou Bla bla bla like ist says     .



thats a great idea Peterae about the motor on the secondary . the only way i see that working is with a cap r/c discharge circuit that inches a cam to the micros . Build it . its a good idea and there is no loss in the secondary circuit  thank you for the input

[innovation_station]

99 take the time read the 1000 pages ....

then go write the book 

ok

we are the reserchers ...  if you want cold undisputiable proof   ill grab pattends from my last time around this silly rock ...

if you think this is something ...  lol  you got 1000 more comeing     no worrie gary is on the "G"  lol

imagine .....    oooo  whats g  ya say ...  just unlocks all tesla... 

look around....  i solved this years ago ... posted all public ...  lol

pony pays 300$ to be a judge ... but he had no idea what he signed up for    lmao

have fun ! 

[poynt99]

@pony . ? I appreciate you comments but i have enough now and i am going to win this . 100% positive . yes that's bold  so you better know i mean business . I wont argue anymore with you . it don't matter whether  the charge cap has 0 volts (which the never do) or half a volt . it will go ou either way . .500 volts is where they normally sit around here as they stop working  silicon hence .5 is where i will start My next repete of the  same Experiment 1 and 2 . today !! and as far as measurements i did all that is needed before . I will log it this time  on paper and video .i'll borrow someones high speed to upload it but its pointless doing that because there is always some one somewhere that says is a fake and its no ou Bla bla bla like ist says

You're welcome to try for the OU prize. I'll give you that. But I don't agree that you've provided sufficient evidence to merit it, and in the end, you'll see that this is true. Good luck.

.99

[innovation_station]

you dont need there prize gadget!   

lol

125 a kit ... you list them ill build them ...

lol

and who knows perhaps we become so busy ...  this site is left in dust ... 

o right and no pattends are gained ...

o right we havent even pulled out our prize chess player  card yet ... 

[MileHigh]

@All:

I am just going to back up .99's comments.  I have read quite a few of Gadget's postings and looked at his schematic.  Gadget has not done anything even remotely close to proving that this is an over unity device.  The most basic measurements of power out vs. power in or energy out vs energy in have not been done.  In addition to this, Gadget is not capable of articulating what the circuit is doing in a proper manner and it is very obvious that his understanding of electronics is very limited.

I would strongly advise anyone contemplating spending the money and time to replicate this device to not do so - you will be wasting your time.  As an alternative, you should encourage Gadget to back up his claims with real measurements proving his claim.  Personally I don't believe that Gadget is capable of doing this.

This is nothing more than another "false alarm" where somebody gets all excited about a JT-like circuit that charges a capacitor using a discharging inductor going through a diode.  There is nothing here.

Some of you may remember the "Imhotep" excitement where there was a huge buzz over turning a computer fan into a small Bedini motor.  The name of the thread was "Free energy at last - A must see" or something like that.  Imhotep became a "rock star" but nothing he and his wife ever posted came even remotely close to being a free energy device.

I encourage all of you that are contemplating replications to just sit back and chill for a long time and see what happens.  I assure you that you will be wasting your time and money.  Instead demand that Gadget prove his claim first.  That would be the wisest course of action.

MileHigh