Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Solid State Orbo System

Started by Groundloop, January 06, 2010, 12:21:24 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages 1 2 3 4 ... 148
User actions

Bruce_TPU

#5
January 06, 2010, 12:56:10 PM
Quote from: Groundloop on January 06, 2010, 12:45:19 PM
Ben, Bruce,

Thanks. :-)

I will continue my work in here. That way we do not have to clutter up the other thread.
I have not tested the flux bar from magnet to magnet yet. But I do not think it is needed.
My research shows me that if the magnet field is too strong then I need a huge current
going in the toroids to block that field. There is a balance between magnetic field and
the power needed in the toroids.

Alex.

Could you not build some sort of switching device that will only allow the steel from one side to the other to connect ONLY when there is no power to the toroids?  This would be like a flux booster and yet when the toroid is turned on and is in "blocking mode", it is only having to block the same flux it is blocking now.  Just a weird idea, I know... but that is me!  LOL

Cheers,

Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Groundloop

#6
January 06, 2010, 01:09:24 PM
Bruce,

Everything is possible. I have tried to explain the problem with
too strong magnets on the toroids. There is a limit to the toroid
cores ability to shield the magnetic field. If the field is too strong
and if we already are powering the toroid cores to the saturation
point, then all power increase after that point is wasted as heat.
A cross bar at the magnets will make the field so strong that there
is not enough magnetic shielding left in the cores to overcome this.

Alex.

dradak1

#7
January 06, 2010, 01:23:37 PM
That's the spirit - congratulate Alex - will be really sad that you didn't continue sharing you excellent work.

Cheers,

Dragan

Groundloop

#8
January 06, 2010, 01:37:55 PM
@oscar,

>>when you wind your next generator coil, maybe you can put a centre-tap in it.
>>Then you may want to test this arrangement again:
>>Maybe you will get "two outputs" with the centre tapped generator coil.
>>measuring between each end of the generator coil and it's centre.

I have tested the NN and SS magnets arrangement on my toroid ends.
I measured zero (or very close to zero) voltage between the generator coil
ends and also between the center taps and the ends.

Alex.

Groundloop

#9
January 06, 2010, 01:39:13 PM
@dradak1,

Thanks.

I think it is important to also research the magnetic shielding effect.
Any more builders on this system?

Alex.
Print
Go Up Pages 1 2 3 4 ... 148
User actions