Muammer Yildiz Magnet Motor

[Gwandau]

Below are stills that I have captured from the video taken at the demo at the university in Netherlands,
images that may enhance the thought processes started in this topic about harnessing the eddy field geometry.

The rotor is made of plastic and so are a few of the stators, but some of the stators are for some reason made of aluminum.
A brief look at the rotor gives an estimate of approximately 250 magnets, and according to Yildiz there are another thousand magnets in the rest of the array.

[TinselKoala]

Oh good grief.

In the video above, titled "magnet assist evidence", what is being shown is nothing more than a rotor on good bearings responding to a magnetically repulsive "hill", evidently a single one per rotation of the rotor. "You see the future"..... what a crock. You see the past.
https://www.youtube.com/watch?v=NsWfHWJTlf0  (WARNING: FLICKERING FLASHING LIGHTS, don't watch if you have a seizure disorder or are sensitive to flicker. Look away if you feel nauseous.)
Here, in this video, from around 1:00 to around 2:00 I show the _exact same effect_ only with 4 hills per revolution in a powerful little fan, made in Taiwan years ago, that uses repulsion/attraction instead of just attraction alone. When the fan is not powered, a gentle push with the finger rotates the rotor around, and as it slows, you can see it getting the same "assist" that the makers of that video above want you to think is "the future". And when it slows even further, it begins to bounce back and forth between two of the potential hills, but since there are four in this fan instead of one, the bouncing takes up only a fraction of a full revolution, whereas in the Yildiz "motor" with a single active hill, the bounce takes up most of a full revolution.
You'd think Sterling had never seen a repultraction pulse motor before. Well, maybe he hasn't, most pulse motors are attracpulsion (Bedini) or core effect (Steorn) kind, and they do behave differently, showing a "quiver" as the rotor is locked in a potential valley, rather than the "bounce" between potential hills like a repultraction motor.

The nice collection of images from the disassembly misses the fact that the motor was not _completely_ disassembled at that demonstration. From what I understand, the entire lower half remained assembled, and only the bits that you see actually in those images were removed and passed around for inspection. Since it's made of identical modules.... that should be sufficient, right? Besides it's nearly time for lunch and Yildiz has a plane to catch....etc etc etc. Nobody, or at least nobody who is talking, perhaps not even Duarte, has actually seen the _whole thing_ disassembled. If you doubt this... why, if it was taken apart at Delft or Eindhoven, did Yildiz have to go hide in a closet for twenty minutes before being able to start it the first time at this demo? After all--- we've already seen the parts, right?
Right.

[TinselKoala]

Hi TK
there is also some other possibilities.
1. A wind up spring lol (with enough tension anything is possible)
2. The device actually runs on magnets until they are exhausted (unlikely)
3.  That many of the magnets are batteries in disguise (rather cool)
Of course there is the question of the mysterious controller Box
For the record I have been calling this one fraud for years, and one of the main reasons I have been banned of free energy news.
I have never seen any magnetic motors running self looped, or any other device that could sustain itself long enough to discount other energy sources.
I do enjoy your posts (despite your low opinion of me)
Kind Regards
Mark (Thailand at the moment)

Mark, I don't have a "low opinion" of you. I just think that you should share with your public, when you report on your trips and investigations, where the money came from to fund the trip and investigation. You don't have to be specific, just categorical: I paid for this trip and expenses myself with my own money, My sponsor or a group of interested potential investors paid for this with their money, The claimant paid all or part of the trip and expenses as part of his/her "validation".
The story of Mister Wayne Travis, who apparently paid for some of your expenses in an attempt to get your endorsement and/or help as a consultant, and who now is continuing to fail to demonstrate the "self runner" that he has claimed to have for years, is a case in point. He got months of credibility out of hiring you (in one way or another) as a consultant, but it wasn't clear in your reports that he was supporting your visit financially.
In case anyone is interested, every single one of my investigations that I have ever reported on here or on my YT account was paid for in full by me and myself only, with the single exception of Orbette 2.0, which was funded by an interested group of potential investors.

[MileHigh]

But we got to see the impressive Swiss Delegation!  It was like WWI!  Sterling is not in Kansas.

[CazadorDeTruchos]

Try reading Sterling's demo report for April 11th. It's really awful and grotesque:

"I am even more convinced today than I was yesterday."

CONVINCED?. GOOD JOB STERLING!!. NOW WHAT? . A speech about KARMA?

Meanwhile, no power measured, no torque measured. Sterling is in the summer time.

Remember Allan: you travel to GENEVA thanks the efforts of hundreds of volunteers who paid for your trip and stay.

Let YILDIZ to do his "FAN DEMO FOR EVER", but you do your job!
Or refund the money to the people who paid for your assistance!

I know that Allan is not an engineer guy, so I am going to comment on one of your points, please don't take offense:

A video on Youtube IS NOT a scientific proof of anything!. You need to understand this, please!!!

Many witnesses claims the YILDIZ´S MOTOR can be stoped WITH ONE HAND.

Until now, this look a well done magic trick.

Please, can anyone talk with Sterling A and say this?

DO YOUR JOB STERLING! REMEMBER THIS!