I got these messages from a youtube user:
TPU REVOLUTION BY STEVEN MARK-OTTO-KEB HAS STARTED IN 21012 IN RUSSIA !!
FREE OU-POWER TO ALL NATIONS
http://www.youtube.com/watch?v=FVMpoRhZLnA
FULL POWER 100W LIGHT BULB FULL SHINE.
http://realstrannik.ru/forum/29-tpu/267-tpu.html
FOR MORE INFORMATIONS WRITE TO INOGDA1 AND KEB ON RUSSIAN FORUM REALSTRANNIK.RU
PS. THE TIME IS COMING !!
PLEASE SHARE THIS VIDEO AND CONSTRUCTION DETAILS ALL OVER THE PLANET !!
Here is another message:
I give to you and all OU friends information for Inogda TPU replication
Inogda TPU have dimensions 6 inch x 4 inch. The collector was made from copper bar 2,8mm x 6 mm (depth and height).
Copper bar dimensions
length: Outer -- 478,536мм
length: Inner -- 319,024мм
length: change of the base ~55мм (one, you need 2 = ~110мм)
altogether: 907,56 (take two pieces 950мм -- remainders go on two leads
This is for one ring!!
Three driving coils. The lengt of winding in each coil must be ~ 24мм (Important: not longer from 24mm!!)
The driving coil have two opposite windings. Take for primary multiple-core cable 0,7-0,9мм isolation must be fluoroplastic.
Take 2 fluoroplastic wires each lenght 4,2м. Wind both together - bifilar winding (end of first wire to begin of second. This is for primary. The secondary winding also must be from fluoroplastic. Take for secondary fluoroplastic multiple-core cable minimum 0.5мм. You can use 0.7мм, lenght is 10.5м.
You need to wind in meters not in turns.
First wind secondary winding then turn the coil 180 degree around his axis and wind primary bifilar. Do it for all three driving coils. The angle between body axis on collector you know 120 degree between coils. The temperature of driving coils is about 50 degrees. Check the correct polarity of windings with compass. The magnetic fields from primary and secondary must be opposite each other !!
Don't touch collector when it work and don't move Z axes of collector !! The Z axes must have direction up.Must look to stars !!
The collector rings must be well isolated with several layers of fluoroplastic or better thermo isolator. This is the most important. Don't put hands or head in the center of TPU when is working. It's very danger. You should to know that you will make a very strong torsion field and don't put any diodes on output. This device is not a toy. Remember what Stiven Mark said anout power of torsion field. I will tell you that with this kind of torsion field you can change the atomic structure of matery when the field is modulated on the right way!!
The device must have emergency switch. Explosion of 700 gm. of copper is equivalent to 1000 kg TNT. So don't use 3 frequencies !!
You must to have several stages sharp LC filters in all power leads of generator and output stage of MOSFETS. Use the best quality parts especially condensers, HV-MOSFETS with shortest transition times and MOSFET drivers. Use HV-condensers of min 630V with best dielectric you can find.
The you need good quality HF pulse generator from 0 to 10MHz with very fast rise and fall pulse times. Remember the collector start working when you pulsing driving coils from 430KHz and up to 2.5 MHz. This is for copper rings. The tuning is very sharp because TPU device use principles of NMR so you must have very smooth and continious regulation of frequency and phases. You will work with one frequency and three phases. (Not 3 frequencise) The phases must overlap between each other min 10% of pulse width. Build good 3 channel phase shifter from 0-30% between each two. You need to have independent smooth regulation of each phase.
Start-up with 10% overlap and when sweep frequency from up to down . From 2.5 MHz down. The lower limit is 430KHz. The correct oscillogram for collector you can find on site realstrannik.ru. Also the positions of driving coils and many interesting infos. Use extremely big cooler with good computer fans for cooling output MOSFETS with very small termal to ambient resistance.
Trim frequency and phase overlap for maximum outpu. The numbers aren't important. Each collector has his own intrinsic parameters, have own "LIFE" when you succeed to "born" him.
That is all. Share this data all over the world. For more informations write to real strannik forum.
PS. The mankind need free energy and will get it!! Will find energy in enormous quantities !! PS. I wish you good health and luck.
TPU was tested with this load: 150W light bulb + nichrom fire-bar element 5KWatt+ nichrom fire-bar 5KWatt+ nichrom fire-bar 2KWatt. With bigger load, current consumption is smaller.
The real invertor of TPU is Nikola Tesla. Find his patent â,,–xxx382 from 1888 year. The output of Tesla's TPU: Diametar 1m, Voltage 10000 V, current 30 A/mm2, Frequency 900KHz, Output Power 7,2 MWatts.
More info:
Some more important datafor coils
The whole lenght of primary coil is 4.2м so take two peaces of 2,1м and wind bifilary then conect it like i said and you will have lenght 4.2м. But first wind secondary.
This is very importnat!! When you winding one layer of secondary put immediately very good isolator between that and next secondary layer. For the isolation between each two layers of secondary use two kind of isolators. The first mica stripe or mica adhesive tape and when fluoroplastic tape. (Teflon tape or P.T.F.E. tape). Do the same for primary winding !!
Now about trimming driving coils.
Put coil on table, over put compass, coli axis arrange from,west to east. Then make sparkle from accumulator on primary winding without resistor. When you find North pole of coil draw an arrorw. On collector all arrows must look in one side (clockwise or anti-clockwise work the same). Simply make positions of each North pole driving coils in the same side.
This is all. Any other information on site Realstrannik.RU
Please
Ask the guy for a diagram or picture of the actual device he is describing so that the info can be put into context.
Other wise somebody might draw one and the confusion will begin again.
I see that otto's ecd circuit is on the first page of the thread .
OK, very good job:
But does the guy will open source this: furnishing the EXACT plan with EXACT characteristics, (Materials, dimension, component used, voltage, current, waveform, and method for tuning). In fact a plan to build the EXACT replica show in this video...
Why ? Because like many many other FE devices just a couple of claims, video, photos...
Talking about exotic theory and 20 years later no one successful replicated --> another FE device lost...
otto ?
http://realstrannik.ru/forum/29-tpu/267-tpu.html?limit=18&start=1944
Just to remind; probably the most comprehensive OTTO DIRECTORY:
http://purco.qc.ca/ftp/Overunity.com%20-%20Forum%20members/otto/
Which Tesla Patent? Is it this one 382,282?
If this notion is possible then a small amount of utillity power can be used to make a lot extra power to run stuff.Or even a small solar array tied to an inverter to run the freq gen to drive it along.
The TPU is not so complicated like Otto's type. TPU is 3 Tesla coils device, no more. most of us were puzzled by the name of COLLECTOR, what real thing it is? ...why use 3 frequencys? you may find the anwser from math, not guess from technology , otherwise just wast your more time.
Quote from: Doug1 on March 03, 2012, 08:19:00 AM
Which Tesla Patent? Is it this one 382,282?
If this notion is possible then a small amount of utillity power can be used to make a lot extra power to run stuff.Or even a small solar array tied to an inverter to run the freq gen to drive it along.
This is the Tesla with the two quadrature phase input ? I have studied this a long time ago, it have a weird connection at secondary: the connection are in opposite polarity and will act like short in a conventional trafo.
Also an import thing: the two phase are not rotating (I have made FEMM simulation) but rather make pulse and varying the inductance (when field push against themselves) a parametric generator ? (Parametric generator can bring large amount of power see Chris Carson (RIP) and Eric Dollard for this... According to their claims even energy conservation is broken you can destroy or synthesize energy at your will like a "God" ... )
Quote from: SchubertReijiMaigo on March 03, 2012, 02:26:50 PM
This is the Tesla with the two quadrature phase input ...
Here's more about this:
http://www.overunity.com/index.php?topic=2300.msg221623#msg221623
Thanks Quert
Seen this on one of the pages linked in the russian site above so I ran it through google translate. 100 pages :o
translated_TPUINOGDA2012FINAL (http://www.overunity.com/downloads/sa/downfile/id/490/)
Thank for your input: It look like that magnetic "Kick" is a common trait of those TPU type device but it seems that a lot of tuning is necessary not easy !!!
I understand better now what it's so difficult to reproduce this device, OMG !!!
.
Don't asking for video proofs. We don't need argue to anybody. You have all important data for successful replication. MAKE IT and RUN IT. Use for your family and yourself. Don't make public presentations and don't try to patent this. This technology belongs to only one man. And there can be only one. Don't think you are that one. The Great one is only NIKOLA TESLA. Will past several thoudsand years to born a man like him so don't think high about yourself. If you frends ask for informations don't sell it. Give it a free. Remember Free informations and Free man makes a Free society. If you wish freedom free yourself and other people who need Freedom and remember Free Society Energy really imply Free Energy. We wish you luck in fight!!
Hi Kaduci,
thanks for posting the information about inogda1's TPU/ECD.
Please continue to supply this information, even if there seems to be not much response in this thread at the moment (which is good, as there is also not much noise).
In the first posting of this thread it says:
Quote from: hartiberlin on March 02, 2012, 06:12:05 PM
Build good 3 channel phase shifter from 0-30% between each two. You need to have independent smooth regulation of each phase.
Please, can someone post such a phase shifting circuit or a link to one?
I am specially interested in the most basic and simple approach to phase-shifting.
Thanks
Hi, Oscar. I guess, the guy from this link (Les Banki) has knowledge in this matter. My hint is to trace his posts rather than asking him since he is rather rare guest in this forum.
http://www.overunity.com/8289/bob-boyce-hex-controller/msg314916/#msg314916 (http://www.overunity.com/8289/bob-boyce-hex-controller/msg314916/#msg314916)
Also Bruce_TPU threads can help:
http://www.overunity.com/12144/eblv-gen-design-by-bruce/msg318353/#msg318353
Hi Qwert,
thanks for the links.
Unfortunately the circuits are way above my head to understand.
I think gmeast's approach is probably straightforward, but I don't understand it
I need a kind of a "primer to phase shifting for dummies".
Thanks for schematics Kaduci. I have some questions about the details though:
1. How many turns for the coils, what kind of wire, are the coils wound on top of each other, or are they interleaved ?
2. Driver part schema is missing, no matter how simple it would help to have exact diagram.
3. Part with Moebius coils is a total mystery. Step by step how to make core shown would help to avoid confusion. Now I see a picture that looks like it is broken.
For example, what kind of copper stripe, what width, thickness or does it matter ? More copper means more output ?
4. Any hints how this could be self looped ?
You have working device ? Could you give answers to above questions so that it reflects your device ? Also, what kind of output to expect from your reference device, power after rectification ?
This seems simple enough to build, no hassling with resonance so it would be easy to get it working.
Hi.
On the first page of this thread there is address to the Russian site: RealStrannik.ru where is the info from; however, this Forum's Moderator translation is so bad, it brings only confusion. Instead, I advise to go to "Downloads" section of this Forum and download the very last document titled "Google Translated TPUINOGDA2012FINAL (http://www.overunity.com/../../../../../../downloads/sa/view/down/490/)" and at least another document titled "Tao's TPU specs (http://www.overunity.com/../../../../../../downloads/sa/view/down/251/)" which presently is on page 7 of that "Downloads" section; this doc is the best and very concise explanation of the principle of TPU and it is mentioned several times on that Russian thread. Then on page:
http://purco.qc.ca/ftp/Overunity.com%20-%20Forum%20members/otto/a-pdfs/ (http://purco.qc.ca/ftp/Overunity.com%20-%20Forum%20members/otto/a-pdfs/)
are all docs which the Russians refer to and which are just the work of Otto. There is some YouTube video material on that Russian page but it needs to go straight to their posts to see it.
I see it now, that Stefan's translation is better than that other one from "Downloads". The size of the collector rail(rod) is 2.8mm thick by 6mm wide by the given legth which gives 6 inch and 4 inch diameters, and so on... The thickness of the collector rails however don't need to be so strict, as it comes from later posts.
Hello OU people !!
My friend Sergei told me to make intervention in this topic about inogda1's TPU/ECD.
First stuff i was observing is next. You didn't read information carefully which were presented by hartiberlin. Nobody need from you to read the lips and to read between rows !!
The informations are quite precise. In some patents you can't find such precise data. So read it slowly and try to understand. Make an image in your heads!! Think yourself, nobody will not do for you !!
Now. This TPU working usinig one generator with 3 phases and only one frequency not 3 generators with 3 frequencies !! We don't using Otto-Ronete generator !!
Here are schematics of some good 3 phase generators but with Russian ICs. If you can't find IC's you need to make own schematic with IC's you can find !!
It's not so complicated. You need good master oscilator with smooth regulation of frequency and relative pulse duration (pulse period-to-pulse duration ratio). Don't use DDS generators. We need very smooth frequency change !! Make it with good RF transistors and quality capacitors !!
What are we looking for ?? We hunt for Cooper collector response for our very sharp impulses. It depend of many parameters. I don't talk about theory now !!
We need to sweep all frequencies from 2.5 MHz down to 400 KHz. The treshold when TPU collector "revive" and born energy is very sharp. Like trimming station on KT radio band. With 3 frequencies you can search all life and don't catch the goal. And according to Stiven Mark words there exist very dengerous treshold when 3 frequencies come close together cooper colector NMR resonance and something more and do explosion.700 gr. of Cooper pire have equivalent of 1 Tonn of TNT !! It's not critical mass of Uran but enough to kill yourself and destroy the buildinh where you live. We are not terrorists but OU hunters and we need Free Energy for us and our families!!
Here are more pictures !!
Next !!
Hi there,
I would like to add my understanding in how TPU works as a gift to everyone who are trying hard to build it:
http://www.youtube.com/watch?v=G9KEBOC4coQ#t=29m41s (http://www.youtube.com/watch?v=G9KEBOC4coQ#t=29m41s)
Hopefully it will help to finish the long mission of power and multiple fields generation from magnetic vortices in toroid shape generators.
Cheers!
This design is so FAR OFF it isn't even funny. SM said if 1 little thing is even a tiny bit off, it WON'T WORK.
This design is 87 MILES OFF. Look at the pictures below to see what I mean.
Bruce TPU thought his "great design" would work too, but it has been 3 years now and NOTHING.
Quote from: FatBird on October 13, 2013, 06:23:51 PM
This design is so FAR OFF it isn't even funny. SM said if 1 little thing is even a tiny bit off, it WON'T WORK.
This design is 87 MILES OFF. Look at the pictures below to see what I mean.
Bruce TPU thought his "great design" would work too, but it has been 3 years now and NOTHING.
There are two designs followed in Russia.
One is Otto version the second is more close Steven Marks and close to particle accelerator way with the taste of magnetic tornado (Searl SEG way).
The difference between Otto, Ronotte and team frequencies collision version and Russian actual field movement version is in place of how magnetic field is made to move around a ring and drag electrons along collector coils. There is big difference in output current when the precise electrons flow is achieved. Also there is another big difference when the electrostatic field is introduced inside of toroid for making flow access to even more electrons from environment into collector coils.
In the video Wesley posted my understanding and explanation about TPU goes on this second design. And it is real working setup with current amplification of many times over collector coils just it will take time to appear in English translated documentation as it is still being worked on replications in Russian speaking countries.
Cheers!
Here (http://www.youtube.com/watch?v=9_3SRc8uaYo) is a video I made replicating SM's 6" TPU two years ago. Mine is a fake made up of NICAD batteries and an inverter made from a small transformer. Looks very similar to SM's TPU in the attached pic.
http://www.youtube.com/watch?v=9_3SRc8uaYo (http://www.youtube.com/watch?v=9_3SRc8uaYo)
Hi Kaduci
Thank you for sharing all the info.
Can you please tell me if the duty cycle is fixed @50% for the three phases?
What is the distance to the lower copper ring from the top ring, is it critical?
Regards
Kent
For driving signals I attached example of test case.
Also the driving coils should be wound in same way as in E. Leedskalnin PMH and should be next to each other, say 16 with 4 running at once around circle.
P.S> The compass in middle of TPU should start spinning around for the first condition to effect.
T-1000
Thanks for the simulation.
I can see you have 10deg phase shift, that is 40% overlap. I don´t know if that is what kaduce mean.
10% overlap as I see it would be 40deg phase shift, if we use a fixed duty of 50%.
Kent /
where is the russian information on this 3 phase driven TPU that works.
its easy to make a phase adjusting oscillator, but theres so many possibilities to test, thats the real problem.
Just to clarify, Inogda never made any video evidence.
The thread of his has died out on realstrannik, I see pictures of different strange devices by different people.
Quote from: T-1000 on October 13, 2013, 08:10:08 PM
There are two designs followed in Russia.
One is Otto version the second is more close Steven Marks and close to particle accelerator way with the taste of magnetic tornado (Searl SEG way).
The difference between Otto, Ronotte and team frequencies collision version and Russian actual field movement version is in place of how magnetic field is made to move around a ring and drag electrons along collector coils. There is big difference in output current when the precise electrons flow is achieved. Also there is another big difference when the electrostatic field is introduced inside of toroid for making flow access to even more electrons from environment into collector coils.
In the video Wesley posted my understanding and explanation about TPU goes on this second design. And it is real working setup with current amplification of many times over collector coils just it will take time to appear in English translated documentation as it is still being worked on replications in Russian speaking countries.
Cheers!
@T-1000, what information are you referring to that makes you believe there is some recent success regarding this type of
single frequency TPU. Yes, that is great in terms of reducing possible permutations, I'm all for more easily achieveable objectives... But...Some people in Russia...wich people may I ask ?? where are their information sharing ? These pictures, they ended up working device of just forgotten scuptures ??
You are explaining, I am listening, yet I do not see system yet... Perhaps you know more than I do about the russian forums.
I see Inogda's posts, 100 feet vertical of russian letters with no pictures or videos, I also see other baffled people responding with occasional pictures of sculptures.
I can make this, a 3 phased out of phase not necessarily 120 degrees type of circuit, duty could be controlled as well, if you want ... I can even write a program that will sweep through everything possible in between those line and store some measureable unit in memory and graph that. But all this is useless unless device worked.
What makes you think all this un-necessary bells and whistle would accomplish ??
@ anybody who is following this TPU device closely and everywhere
Where is VIDEO PUDDING ??
Where is clear evidence of success from these russians ?? Because it seems as if everything went silent? and all those pictures are just non-functionnal.
Sorry for being so negative but whats the big deal about providing video proof, Kapanadze does it, so does Andriey and SM... Why now restrict evidence ??
@ Kaduci ( if you are still around)
Am I supposed to believe your claims and invest myself in your words alone ??
Quote from: ARMCORTEX on October 16, 2013, 11:19:47 AM
@T-1000, what information are you referring to that makes you believe there is some recent success regarding this type of single frequency TPU. Yes, that is great in terms of reducing possible permutations, I'm all for more easily achieveable objectives... But...Some people in Russia...wich people may I ask ?? where are their information sharing ? These pictures, they ended up working device of just forgotten scuptures ??
Yes, that is correct, it is single frequency making magnetic tornado in the ring.
Please see Searl SEG to get idea on what is going on there - http://searlsolution.com/technology2.html (http://searlsolution.com/technology2.html) and http://www.searlsolution.com/evidence2.html (http://www.searlsolution.com/evidence2.html)
It is mechanical version of TPU/gravity machine there.
Quote from: ARMCORTEX on October 16, 2013, 11:19:47 AM
You are explaining, I am listening, yet I do not see system yet... Perhaps you know more than I do about the russian forums.
I see Inogda's posts, 100 feet vertical of russian letters with no pictures or videos, I also see other baffled people responding with occasional pictures of sculptures.
Please be patient as it was picked up only recently with second replication of TPU in Russian speaking countries so in terms of information sharing it will take time.
I am sharing everything openly much as I can to bring in practical way... ;)
Cheers!
@ kent, I also wonder what Kaduci means, he is probably not the expert who built this most likely a messenger of somebody else. Best way to sustain a tornado is with 3 phase, I dont care if its ''ether'' or magnetic particles.
@ T-1000
Can I see this video ?How recently was this.
This could be a fun project and not too expensive, pretty much have the chips ready to go.
And theres always the slim possibility that I succeed. Otherwise I'll have a sculpture as decoration.
Hi there,
Here is some crude experiment done based on Sergey's circuit to see if circuit works at all:
http://www.youtube.com/watch?v=QS9hqqwC75k (http://www.youtube.com/watch?v=QS9hqqwC75k)
"To be continued..." 8)
Thanks for that document T-1000. I'm not sure if it was available anywhere in English but I did translate it to English using a couple programs and Google translate. Attached here in English. Not sure I got all the pictures/diagrams in exactly the right place but they should be close.
Quote from: T-1000 on December 14, 2013, 07:40:50 AM
Hi there,
Here is some crude experiment done based on Sergey's circuit to see if circuit works at all:
http://www.youtube.com/watch?v=QS9hqqwC75k (http://www.youtube.com/watch?v=QS9hqqwC75k)
"To be continued..." 8)
Should I share a theory about those bubbles of electrostatic?
(s/Should I/I'm going to, if you'll pay attention a little, and offer criticism.../)
If you have a pulse, you have a momentary (compression) wave followed by a (rarified) trough. These represent themselves in induction as the rise and fall of current on the primary DC.... so there's a north and a instant south, in which is a packet of electrostatic... is this good? Maybe not... really I think my marks on good/bad resonance is actually both bad, and somwehere in the middle where the field is also intersecting the winding is better. So having a gap beween the center and the pickup winding would be better... (a aircore, winding, aircore, perpendicular winding)
Daniel Nunez's coils do this but cross-hatched-wise... (I dunno I think he's shorted some windings that he can do better)
Resonant gravity field coil
http://www.keelynet.com/gravity/gravity3.txt (http://www.keelynet.com/gravity/gravity3.txt)
Power requirements are ridiculous for that tough...
but it's a central flat coil in a circle surrounded by a toroidal wound coil...
Quote from: T-1000 on December 14, 2013, 07:40:50 AM
Hi there,
Here is some crude experiment done based on Sergey's circuit to see if circuit works at all:
http://www.youtube.com/watch?v=QS9hqqwC75k (http://www.youtube.com/watch?v=QS9hqqwC75k)
"To be continued..." 8)
Hi T-1000,
Thank you for the update as I was very curious to see how all of this has been progressing since your original posts. I can't understand Russian but wanted to as you if the man in the video mentions anything about the prototype putting out pulsed DC? Even if it has a COP < 1 at this point, it would still be encouraging to know if it is exhibiting any of the claimed effects.
@All,
I did a rough translation of the PDF file (using Google) and also included one of the circuit diagrams which were translated into English as well. It is attached below.
I am also working on a Data pattern generator board which uses simple dip switces and logic gates to create the pulse pattern shown in the PDF. The board will be able to be clocked from a function generator up to a max clock speed oh 20 MHz. If there are any other replicators out there who are interested, let me know and I'll keep you posted once the design is finished.
Thanks,
Jason O
Quote from: T-1000 on December 14, 2013, 07:40:50 AM
Hi there,
Here is some crude experiment done based on Sergey's circuit to see if circuit works at all:
http://www.youtube.com/watch?v=QS9hqqwC75k (http://www.youtube.com/watch?v=QS9hqqwC75k)
"To be continued..." 8)
Is the device ou or is he just showing that it works