Hi,
here is attached a video from Jim driving with his modified MEG type
Harmonic Oscillating Power Electric (HOPE) generator via a soundcard
2 neon tubes.
I hope he will post more info on the circuit.
Regards, Stefan.
Hi Stefan,
To light up the two neon tubes, so far I have only been able to use the sound card from my older HP Pavilion to get enough audio volume. The Portable CD player does not reach the apparent critical volume level necessary to reach the point of lighting two neon tubes. There is a certain db level needed to start the harmonic reaction in the materials used to build the unit, and at this time it is not completely clear what exactly is going on to cause the unit to generate energy, but a few good engineer's do have some interesting theories about this. When a certain level of volume is reached the unit immediately jumps up to at least 1000VAC and 2 amps minimum. Even the smallest increase in volume after reaching that critical level causes the power level to jump several hundreds of volts at a time. Right now I can't even turn the volume all the way up and get a reading with my multimeter because the power jumps up so high that it blows out my meter. The limits have not been tested yet by any means, but I am hoping to be able to do something about this soon. We have been hung up in the process of trying to sell our home and there are a lot of problems with the buyer's getting their loan approved etc.., etc.. . This device is similar to the MEG but highly modified. The wiring configuration is novel to say the least, and is far from the conventional circuitry we are used to in electronics. If I was to try and input AC the way it is wired for sound right now, it would short out and simply not work. However with a few small changes I can convert it to use AC input and get over 1000VAC with only 24VAC 1000mA input. I would not be able to read any amerage at all by using AC as the input. The fact is, that I can get much higher output both in volts and ampere's by using sound frequencies as the input, and it takes much less energy to generate that sound than it does to use electricity. The unit never even gets above room temperature no matter how much energy it produces or how big of a load I put on it. It seems to light four neon tubes as easily as it does two. Also, you should be able to link more units on to the first and use the same original sound input because the sound will travel directly through the unit and out again with less than 1v lost to the first unit and no detectable loss in volume. This is a very promising aspect of this design because it means that we should be able to power many units with no more energy than it takes to power one unit. It does not take a genius to do the math on this one Stefan, and the implications of this ability should be obvious to just about anyone. Quite frankly I am a bit nervous about making to much public at this time beyond what I have already said, and there is already a brand new cell tower across the street which has been beaming as much as 4+ volts of AC into my bedroom. I personally believe that this is the reason for the constant migraines that I have been having since this tower went up two months ago. Also, we were already receiving four full bars on our cell phone reception, and I can see no logical reason for suddenly erecting another tower across the street. I have had many threats and attempts to shut me down, and I am seriously worried about getting this device to be witnessed and examined by qualified engineer's and expert's before something else happens. Sterling thinks I'm just paranoid, but I come from a background of working for the U.S., DoD at the center of many black projects which were well above top secret, and I know many facts which Sterling is completely clueless about. I have been threatened face to face in the past by the military and have been under observation by various U.S., agencies a great deal over the period of the last 30 years. These guy's do not fool around, and they mean exactly what they say, so I believe I am justified in having my worries. I have given descriptions time and time again, but nobody ever seems to read or save the information, and I am literally very sick and tired. I have posted photos of every angle of the device which should give anyone with enough interest all that would be needed to reproduce the device, including the wiring configuration. This latest problem with the sale of the house has set me back at least 6 weeks or more again, and I honestly believe that this is a very important discovery that needs to be throughly checked out. I have found absolutely no downside to this device and/or design and every aspect about it seems positive and very promising. I think the problem is that there have been to many phonies along the way which have ruined things for serious inventors and so no one pays any attention any more. There is an engineer in Utah who has volunteered to draw up the circuitry schematics for the design, other than that, I have not found anyone else willing to help except for a guy in town here who just happens to be a reconisance expert for the U.S., Office of Homeland Security. There are other agencies of whom I am aware, who are also watching the ISBP project closely, and so I do not believe that they would be so concerned with my work if there were no reason for this. American's have to be among the dumbest people on the planet Stefan! I am pasting the materials list needed to reproduce the HOPE Generator unit, and I am hoping also to be able to write-up a step by step assembly proceedure as soon as possible for those interested in doing this. Right now I am living with my eldery mother and stepfather who are both in there mid 80's, and there is just to much going on around here at the moment to find the time needed to do this write-up now. If you like, you may post the materials list wherever you want to, and I encourage everyone to build one of these units for themselves. The more people who do this, the less likely it is to be hushed up, and the safer everyone will be in the long run. For those who cannot figure things out from the photos, they will have to wait another month or so at least until we can get moved to a new location. Most of the folks in the ISBP os Project forum have more information than anyone else, but the wiring process is fairly complicated and will need the step by step instructions to complete the unit. I will do my best to get this information out as soon as at all possible, but it is simply impossible right now. I am willing to turn this unit over to someone who is trustworthy and competent if they are willing to draw up the diagrams. One thing I will not do however is to send this unit through the mail. It would have to be picked up in person! I haven't yet met anyone who is willing to do this, and so it will most likely be several months before the specs are posted on the Internet. If something happens to me before that point, you will know for absolute certainty that it was not an accident or from natural causes.
Below is a list of materials you will need to reproduce the original HOPE Generator in it's entirety. This is not a step by step assembly manual, and is meant only to help you prepare to have the right materials on hand in order to build your own unit. A step by step instructions paper will be drawn up as soon as possible. It is recommended that you obtain these materials in the mean time and wait a little longer before attempting to assemble your unit as there are details involved with the wiring configuration that need to be followed exactly for the unit to operate correctly. If you attempt to assemble and reproduce the original unit without the correct wiring instructions, you will most likely be disapointed by the outcome. However, if you wait a while longer and follow the exact proceedures which will be described in detailed step-by-step instructions, you will likely be elated and over-joyed with the outcome. There are a few more details which will be brought up at the time the assembly instructions are posted which may cause many of you to want to build several more HOPE Generators, but for now I ask that you try and have a little more patience with me as there are many matters to take care of before I will have the time to take care of this matter.
Original HOPE Generator Materials
1. AMCC - 320 C-Core:
purchased from - Elna Magnetics (http://www.elnamagnetics.com/)
sales rep., Cindy Clarke CClarke@elnamagnetics.com
The cost of the core is about $104 USD. Approx., $112 Total with S&H.
2. SmCo Magnets minimum grade # (17 or higher):
You can use 1 or many magnets depending on the thickness however the magnets must measure the equivalent of 35mm to precisely fit the core gap.The magnets which I used were purchased from the ForceField web-site at -(http://www.wondermagnet.com/), and measured .50" Wide x 1.0" Long x 3/16" Thickness and were stacked together to precisely span the gap of the core. The length of the magnets were situated along the line between the two halves which made up the total core.
Here is one solution to the problem and I believe that the 1.0" disc magnets will work at least as well and most likely even better than the 1.0" x 0.50" reclangular magnets which I used originally. Check out the web-site and SmCo specs below. The P/N stands for part number for those of you who want to order these.
MMC (Magnetic Material Components)
http://www.mmcmagnetics.com/ourproducts/main_StdParts.htm
SmCo - DISC MAGNET
P/N Length Thickness Grade
SCDS-1000-125 1.000" 0.125" 26 MGOe (2:17)
NOTE: Eleven of these would add up to exactly (34.925mm). A piece of tape on either end may be sufficient to make up the slight 0.075mm difference of the 35mm gap of the AMC 320 C-Core. This is what I did. Also, the various cores may have a very slight difference in actual measurements which can vary within a millimeter or so and you can give "Elna" the exact measurement of 34.925mm and have them mail you the closest match for core gap. Talk to Cindy Clarke at Elna Magnetic Products.
Another possible source for SmCo magnets might be MCE Products although it appears that many of the magnetic products manufacturer's are becoming very closed to working with the general public.
http://www.mceproducts.com/materials/material-list.asp?MaterialTypeCode=1005
3. Both (27) and (29) gauge Tesla Wire:
purchased from E-Bay (http://www.ebay.com/)
I recommend doing a search all catagories search for "Magnet Wire" which is the same as Tesla Wire.
The two spools of wire which I purchased were each 20,000 ft. rolls. I still have enough wire to build several more units, so it is not necessary to purchase such large rolls of wire, however it was much more of a bargain to buy it this way on E-Bay, and it is my opinion that a good inventor can always find many uses for high quality Tesla Wire.
4. Contact Strips:
Two 2" 8 contact point strips
Two 1.5" 4 contact point strips
These can be found at most Radio Shack stores but may depend on the area of the country you live in. These strips are the black strips with screws that you can see in the photo's of the HOPE unit, located on both the top and sides of the unit. They are not absolutely necessary but they do make it easier for testing the unit and will prevent the eventual breaking of the wires due to bending and over handling. They are very inexpensive and are well worth the extra couple dollars in the long run.
5. Cardboard and/or Hardboard:
You will need to find some good stiff cardboard and/or hardboard to cut and glue the spools to wrap the coils for your HOPE unit. I used strickly thin stiff cardboard of various thicknesses to form my spools, but you could also use 1/16"hardboard for the sides of your spools if you prefer. You could also conceivably use plastic if you like but I would recommend using some very strong glue if you do as a good deal of pressure with build up between the two sides of the spools as the number of winds increase while winding your coils.
6. Single Strand Insulated Wire:
2 feet of (Single Strand Insulated Wire) will be needed during the wiring process of building your HOPE unit. The wiring configuration is a novel one!
7. Transformer:
The transformer you use will largely determine the total output both in voltage and amperage, and I would suggest using as large a transformer as you can afford or find. The transformer that I am currently using is an old antique home built unit with variable inputs and outputs, and with a maximum rating of 210v. In most cases you will find that the transformer will substantially improve the total output wattage but I have found that the increase will depend on the size and type of transformer you select. Without the transformer which I am currently using I have noticed that I get only approximately half of the total output. Also, when not using the additional transformer, the wiring configuration needs to be changed slightly in order to achieve an optimum output value.
8. 4 Wire Telephone Jack:
In the photo's of the HOPE gen., you will see a small white box situated on the top center of the unit. This is a 4 wire telephone jack! The reason for this jack was originally for the purpose of conducting bioenergetic experiments using an additional device which for this project is not necessary to go into at this time. However, in order to describe the final wiring configuration, it would be easier to go ahead and add this component to your list of materials needed because of the complexity of the total wiring configuration. You should be able to find one of these in any fairly large hardware store or telephone supply store, and possibly even Best Buy, Circuit City, Home Depot, etc.., etc.. . Without this final component I will have to spend a lot of extra time trying to find a way around the problem and at this point cannot promise that there will be a solution in order to achieve the same results.
9. Stereo Audio Jacks:
This is not one of the required components but you may eventually find that it is much easier to plug in an audio jack than to try to jury rig an audio cable etc.., and so I recommend that you find a female stereo audio jack with at least a couple inches of wire/cable which you can then strip the ends of and easily hook up to your HOPE unit. I have chosen a 1/8" size female stereo audio adapter but it is up to you how you want to do this. You can also find stereo audio adapters which you can use to adapt 1/4" plugs to fit 1/8" plugs and vice versa. These can come in handy if you want to be able to use different sources for your audio input.
10. 1" x 2" lumber:
For the purpose of stablizing and securing the unit, you can use 1 inch by 2 inch pine or fur lumber. If you look at the photos of the HOPE unit, you should be able to see that there are four square blocks of wood on either side of the unit which are placed under the core and on top of the core. You may also be able to see two approximate 5" lengths of wood directly in front of each set of blocks. I used both hot glue and wood screws to mount and secure the unit and found this to be the simplest way of doing this. I also used regular Elmer's Glue along with wood screws to secure the top piece of cardboard to the wood frame. The reason for all of this is to keep the core from seperating and to prevent accidental damage during the process of carrying the unit around.
11. 3/4" Baseboard:
You will need a board measuring a minimum of 6.50" x 10" to build and secure the unit on. Any additional exterior box or frame is up to you, however do not build any exterior box./frame until the unit has been fully assembled and completed.
12. Screws:
I recommend using 14 .50" sheet metal screws for connecting the exterior coils and single strand wire you will see around the base of the unit, and about 1.75" sheet rock screws for the places where you will secure the top to the side posts of the frame. You should also drill a single screw through the bottom of the 6.50" x 10" board that you are using to build the unit on.
13. Adhesives/Glues:
I highly recommend using hot glue to secure the wood blocks and to help level and/or fill any spaces between the core and the wooden blocks and frame. You will also need to use a good liquid glue like Elmer's or something similar to glue your cardboard spools together. Hot glue is not necessary for building the spools, however once they have been aligned to their proper positions on the core, you can secure them with hot glue and this will help to keep vibration to a minimum. You will also need the hot glue to secure the exterior coils to the corners of the HOPE unit after you have mounted the unit and secured the frame to the baseboard.
14. Aligator Clips:
These are not a necessity however I highly recommend that you purchase at least a dozen aligator clips for building and testing your HOPE Generator. It will save you a lot of time and work in the long run and they are not very expensive at all. The clips should be between 12 and 24 inches in length and preferably different colors to make things less confusing than they have to be.
Cheers,
Jim
I just finished fixing my CD-RW Drive and
burned 3 one minute wave files of a 16400Hz Sine Wave frequency onto a CD-R. I then popped it into the cheapo $16 portable CD player
I picked up at Walgreens Drug store yesterday. The CD player uses 2 AA batteries so I figured that if I could light up a fluorescent
light with the CD player running the frequency through my HOPE generator maybe more people would pay attention. Guess what Stef,
........ it works! Not real bright but it does light it up. The CD player uses headphones and hardly puts out any volume but its
enough to give me a reading of at least 360VAC at over .60 amps. I'd like to see anyone do that so far. The player doesn't quite hit
the critical volume to start the cascade effect I was hoping to show but it's
pretty darn close. Just a little amp circuit should do it, and then nobody will be able to argue with me anymore heh-heh. Anyway
Stef, feel free to post the video clip wherever you want and I want to get the info out to as many as will listen. I'm not ready to
claim free energy yet, but I think I'm getting darn close. Another couple months maybe, hopefully. Thanks for writing again, and
stay in touch once in a while okay?
Best Regards,
Jim
P.S. I'll try to get a new vid showing the 2 AA CD player lighting up a tube as soon as I can get to it.
Additional Infos from Jim:
Stefan,
I am attaching half of the photos with this reply and half with the next incoming message. The sound that I am using is produced by freeware software which is available on the Internet. Again, it is totally freeware NOT shareware so you don't have any licensing or advertisements to have to deal with. I usually just use a sine wave only because it is less irritating to listen to. However almost any type of wave can be used including plain old "white noise" or static. The more even the tone is, the more steady the output rate is and the less flucuation in the energy readings. I have even played Beethoven and Chopen through the unit to see if it would work with music. It does produce energy with any type of sound input, but at certain freqencies it will put out much more than at other frequencies. The prime frequencies seem to vary depending on the wiring configuration along with the specific number of additional coils and the number of winds per coil. A little test run through the various frequencies will tell you where your prime frequencies are found for any particular unit. Modulated frequencies are not recommended if you want to put out a steady rate of power as the power output is directly related to the changes and modulations of the sound input. So far I have only used the "NCH Tone Generator" software to test various waves and frequencies and so there is still a lot of room for discovery here. I have also tried mixing several frequencies together to see what would happen but as I said before, a steady regular single tone/frequency seems to give the best results at this point. I have noticed that a square wave usually gives the highest output, however there are certain frequencies which various other wave forms will work just as well. Each time I have made an additional modification to the device I have to find the best frequency all over again because it is very specific to how you have it wired and what materials are either included or excluded. I have also done some tests using various musical instruments to see which ones would produce the highest energy output. Right now the "Oboe", "Trumpet", and "Organ" seem to produce the highest values, but that may be dependent upon the specific set-up as well. I haven't yet had the spare time to test many of these kinds of things. It is very clear however that this technology is very energy efficient if nothing else, as the portable CD player I bought uses only 2 AA batteries and when I play a 16400Hz sine wave from a CD recording I made on my PC, the voltage goes as high as 400VAC at .67 Amps. Perhaps you could tell me what that figures out to in Watts? Also Stefan, as I have stated before, the CD players volume is regulated by the FCC and FDA in this country and is just short of putting out the critical volume to send the output over 1000VAC. A couple of my friends are supposed to be working on building some small amplifier circuits and variable tone generators but I'm not sure they really understand what is needed yet, and haven't even seen the device in person yet. Anyway, save these photos just in case something happens to me before I get around to posting the step-by-step instructions because you can see much of how the device is wired by close inspection of these photos. I do not plan on patenting this device and this is the reason that I have chosen to post it on the Internet. The U.S., Patent laws state that any idea and/or invention which is posted on the Internet automatically become public domain/property, and this is the way it should be. Nobody should have the exclusive rights to free energy technologies or even to extremely energy efficient technologies in my opinion. This is for the whole world and there are absolutely no restrictions to the development and deployment of this technology. Post it wherever you like and encourage other's to do the same is my battle cry. Still I am not yet claiming this to be free energy because things really need to be checked out closely. I do believe that if this is not totally free energy, that it is the closest thing to it that we have seen in many years and I don't think it will take much to improve on this technology to eventually show true OU beyond any doubt. Remember to save the photos now okay? Talk to you later Stefan.
Best Regards,
Jim
Here are the pictures from Jim enclosed in a ZIP archive.
Regards, Stefan.
Hi Guy's,
As you can see Stefan, I'm back. I have decided to put this project ahead of even the ISBP project for the next couple of weeks. My people will understand and they are fully aware of everything that is going on. At the moment I am waiting for a reply from an engineer who has volunteered his help with this project. If he is willing I will be leaving within the next week to run the HOPE Gen., through the ringer and try to find out exactly what is going on. If need be I will leave the unit with him so that he can draw up the specs as soon as possible so that everyone has the complete information needed to reproduce this device in it's entirety. I am happy to answer any questions and am not one to exagerate or embelish the truth. This is a very important issue and believe that hidden facts and details only serve to delay progress in this area. Thanks for all you do Stefan, and let me know if there is anything else I can do.
Best Regards All,
J.D.
More info from Jim:
Hi Stefan,
Are you absolutely sure that your estimate of 268 watts is correct? If so, this would mean either that we actually do have OU going on here, or that there is indeed something very different about this energy which is registering as AC on a multimeter, and that the readings are somehow wrong. I was wondering about this because of several oddities which I have observed. I guess we will have to wait until we can test it with better equipment than I currently have available. Since this is such a touchy subject and because there have been so many mistakes made in the past, I would like to keep any further information on this between us for now. I don't mean that other's shouldn't try and build and test out their own units, I only mean that I am leery of making free energy claims before every last effort has been made to verify all the findings as being accurate. BTW, the sine wave that I am using on the CD is a pure sine wave. Thanks a bunch for giving me the scoop on the wattage values. As for the way the magnets are situated inside the core, they are placed lengthwise along the line where the two halves of the core meet together and are superglued in place. The SmCo magnets measure exactly 1" Long x 1/2" Wide x 3/16" Thickness according to U.S., standard measurements (or) 25.4mm Long x 12.7mm Wide x 3.175mm Thickness according to the metric standard. The magnets I used are grade #17 and were purchased from the ForceField web-site at (http://www.wondermagnets.com/). One more very important note that you will not be able to notice from the photos is that one wire from each of the four input coils is criss-crossed over to the other input coil on the far outside corner contact (or) last screw on the edge of the two top contact strips. In other words, if you draw an X from the outside screw of each of the two contact strips which you see on the top of the unit, that is how the four input coils have been re-wired. Another trickey part is the way that the stereo audio jack is wired but thats a bit more complicated and will need to be drawn out on paper. The rest is fairly simple but very odd as I have said, and can be seen fairly well in the photos. I am sorry that I don't have a very good camera right now, and hopefully someone will have one we can use to take better pictures once I get to Utah. Also, Sterling and his engineer's will then have a chance to take a look at it all and test it out for themselves. It does give me even more HOPE after seeing the figures that you have given me concerning the output in wattage Stefan. Lets keep our finger's crossed that this is really it this time eh? We've all worked and waited a long time to see something actually come out of all of this effort, and it would be a real blessing to know that it cannot be patented by any one person now. I know what I'll be doing anyway if these readings all turn out to be accurate. I'll be the first to set up for full scale production in my area, lol. Oh BTW, I almost forgot about the extra transformer. This has enabled the HOPE unit to use even white noise as a good input source for some reason. I don't know why, all I know is that it works very well. It also seems to boost both the voltage and amperage somewhat and so I'm sticking to what works right now. Since I have also found a way to pass the audio signal directly through the unit at no real loss in power, I figure that it should be possible to power several more units with the same audio input signal as is used in the first module or unit. This would really increase the input to output ratio's and I am eager to try this out soon also.
Cheers,
Jim
Stefan Hartmann <hartiberlin@gmx.de> wrote:
Hi Jim, thanks for the new infos and the pics.
It is now all posted on the same thread in :
http://www.overunity.com/index.php/topic,358.0.html
To your questions;
>. It is very clear however that this technology is very energy efficient if nothing else, as the portable CD player I bought uses
only 2 AA batteries and when I play a 16400Hz sine wave from a CD recording I made on my PC, the voltage goes as high as 400VAC at
.67 Amps. Perhaps you could tell me what that figures out to in Watts?>
Normally, if you have DC you can just multiply the values to get the Wattage.
But at AC you have to multiply in the phase shift between current and voltage
with Cos Phi
as a factor between 0 and 1.
If it is pure sine waves it is easy.
It gets more complex, if it are not sine waves...
So, if the phase shift is almost 0 degrees you have to
cos phi= 1 and the factor is 1 so you can just multiply voltage and current
to get the Watts, that would be:
400 x 0.67= 268 Watts.
Could you still show, how the core is fixed to the magnets
and why you need an additional transformer ?
What is the additional transformer doing ?
Thanks.
Regards. Stefan.
Hi Jim,
268 Watts is probably not the case, as you just light up 2 x 8 Watts fl tubes and 2 x 4 Watts bulbs ?`
So all in all I would say that you are able to generate about 10 to 30 Watts with it in the moment,
so there is probably a phase angle between the 400 Volts and 0.67 amps.
Also meters built for 60 Hz AC won?t measure correct at 16400 hz !
So you better make a drawing of all the wiring and let it be scanned in from
somebody who has a scanner and then you can post this.
Maybe a neighbour of you has a better digital camera ?
Your pics are rather difficult to see, cause they are pretty blurry.
So if you put out about 10 to 30 Watts right now with your 4 tubes,
how much are ou putting in ?
A soundcard can only deliver around maybe maximum 2 Volt AC peak to peak and only
a low current, maybe 500 mA max. so this would give only about 1 Watts of output power.
So maybe we see here already a COP of at least 10, so efficiency is around 1000 % ?
Regards, Stefan.
Hi Stefan,
I have pasted below the report on the latest tests which we conducted on the HOPE device.
I don't know if you want to post this on your forum so I am leaving this up to you to decide.
Hope your doing well Stefan.
Best Regards,
J.D.Fauble
_____________________________________________________________________________
Shalom Y'All,
As you may know I have just returned from visiting with Rob, and we
found out that the current readings were apparently lower than my
multimeter was showing. According to a test using a bridge rectifier
which Bill described to Rob, there was almost no current behind the
high voltage.
I trust both Bill and Rob more than any other friends I
have known throughout my life and am honored to have such great men
as these in the ISBP Project forum.
However, my own personal opinion however is that we
are dealing with a slightly different type of energy which is being
created as the result of the sound energy reverberating through the
various materials which make up the device itself, and is possibly
producing more than just electrons.
What I have seen through the
various experiments which I have tried is that there seems to be some
type of plasma being created which does not act like the AC or DC
electricity that I am familiar with. I don't believe Rob shares the
same opinion, and maybe he is correct, however I am fairly obsessive
about details and am not ready to make this conclusion yet.
I know
that measuring AC current is no easy task, and a good many people
have made the mistake of claiming free energy because of this. This
is why I am very cautious about making such claims.
It is also partly
the reason that I am not so quick to conclude that there is not
something more to the HOPE unit that we do not understand yet. Bill
has a very interesting theory which delves beyond the current
understanding of physics, and which explains some of the anomalies
which I have noticed while experimenting with the device.
Bills
theory would confirm my hunch about what is going on inside the HOPE
unit. If Bill is right, it would mean that the sound input is
basically causing echo's in the unit which produce interjecting waves
within the core and copper coils.
If you understand how a gas laser
works then you may be able to see how sound could actually be
converted to light, or some type of plasma energy when a certain
frequency is achieved.
On the other hand, the trip to Rob's revealed
another oddity which I have yet to understand but could also be
valuable information to find out. When Rob and I ran the frequency
settings which work best at my house in El Paso, we found that we
were barely producing any energy at all.
When we ran through a few
frequencies between 40Hz and 20KHz we found completely new prime
frequencies for Rob's location in Utah.
Personally I find this very
interesting and would like to see what happens when I bring the unit
over to Larry's place about 40 miles from here. What would cause the
various changes for prime frequency settings from one location to
another. Could it be lay lines, or are various radio and/or cell
communications contributing to the function of the unit? You can
probably tell what I mean about obsessive now eh guy's? lol.
Another reason for my continuing enthusiasm concerning the HOPE unit
is the fact that it does directly convert sound to some form of
electrical and/or plasma type energy.
I am interested to see if the
device might be useful for cracking H2O since both sound and
electricity have been used for this purpose for some time already.
Neither Rob nor myself felt that it was worth the while to draw up
the specs to reproduce the device yet, and unless we do find
something more promising than what we have so far I don't think
anyone else will want to waste their time.
I will begin the H2O
experiments within the next week,and I will be purchasing the wave generator soft ware that Rob
uses so that I have more options and frequencies to work with.
Right now some of you may be thinking that I should change the name of the unit to the WISH Generator lol,
but I stil lhave some HOPE for the time being, and time will tell whether
there is any thing more to the device.
One of the things which makes things interesting is that we all see things from our own various perspective's,
and life would be pretty boring
if we all thought exactly the same about everything.
Of course that is only my opinion.
Cheers All,Jim
Here is an update from Jim:
Hi Stefan,
There is some progress on the HOPE tech and I have been able to double the efficiency of the original unit within the last two weeks. It appears that both geographic location and temperature help to determine the prime operating frequencies of the HOPE generator. I've also re-configured the wiring between the HOPE unit itself and the antique transformer that I have been using with it. The new configuration works well and is much less complicated than the old one. A small group of private investor's want to take a look at the device and are flying the best engineer they know of to El Paso in about six weeks as things look now, and we will be working on building a small audio amp circuit which we will try to tune to give us audio feedback at these primer frequencies. I've already tested to see if audio feedback would work and it seems to work better than any tone generator that I've used so far so things are looking positive. Another thing that we figured out is that the diodes that the guy used to rectify the AC in order to test the current output were slow diodes and did not reflect the true amperage. I already knew that the readings could not have been correct because I've nearly been knocked on my backside several times by accidentally touching a couple live leads. I have a lot of personal experience with getting zapped by electricity and I can tell that there is much more than just high voltage with no current coming out of the HOPE unit. I haven't wanted to make to much more known at this point but I am working on that step-by-step manual, and will be sending it out to my friend's and collegue's as soon as it's finished. I will probably have some time to do this now while I wait for the backer's to show up as I don't want to even touch anything until they do. I think were getting a good idea of what is going on within the HOPE unit to cause the kind of output we are seeing and believe that it is due mainly to the nano-crystaline core material that I'm using as well as the way I have the wiring configuration set-up. Now if we can build these things to resonate at healing frequencies that would be yet another plus, lol. The system is built to be modular so that other units can simply be plugged into the previous units and all use the original sound source to increase the energy output. There seems to be no noticable loss in output to the existing unit in the process and so this is a major plus in my opinion. Although the HOPE will produce an impressive amount of output without any additional transformers attached, the particular antique style variable transformer that I am using with my unit does seem to improve on things in several ways. The additional transformer that I am using enables a wider range of prime frequencies to be used, and also helps to increase the voltage considerably. This works great for lighting, however we will have to see whether we will want to use an additional transformer for every other application. There is a lot of work yet to be done thats for sure. But even in this infancy stage the HOPE is looking very impressive to a lot of people including myself, and I can't see any downside to the technology yet. I am forming a partnership with another very intelligent young man in N.Y.C., and we are hoping to be able to bring many more valuable technologies to the people very soon. I won't even go into what we are planning to do for now, but I know that you will be very interested in them all. I believe we all need to take a closer look at crystals and nano-crystal materials and consider sound as a source for energy. It does make sense when you think about it don't you think Stefan? I am supprized that Tom Bearden hasn't picked up on this bigtime yet but I'm sure he'll catch on soon if his health continue's to permit. I've been wanting to be able to talk to Tom for a long time because I do think he is a very smart guy and that he is right about many things. I wish someone would give me a number or address where I could contact him. Anyway, I wanted to tell you that I am making progress on the HOPE tech and have people lining up to look at it and HOPEfully develop it so we can all use this stuff. My partner in N.Y., tells me that he has several hundreds of people who all want to buy one of these units right now, but until we get that mini amp circuit built in I don't want to make any public claims just yet. We're also still looking for 400 series stainless sheet metal to build our wave guides for the ISBP but are having a heck of a time finding it at any reasonable price. Seems like all the industry has gone to China and Mexico, and I think the citizen's of the states are going to suffer greatly for the insatiable greed of the executive's who have been making these kinds of decisions throughout the last couple of decades. Well, don't want to talk your head of buddy so I'll let you get back to work. Take care, and I'll be staying in touch and keeping you up to date on things as they develop.
Best Regards,
Jim
I'm probably wrong but this looks like a c-core being charged with an audio circuit. If the wraps are sufficient and a high voltage is being emited from the c-core tips into the tubes this would cause them to glow. The F-16 flight line techs would tell the "new meat" to grab a 48" light tube and walk to a certain aircraft. They would have the radar powered and the tube would light, nothing new here.......
Rich
Here is the new manual form Jim, he writes:
Stefan,
? ? I just finished answering a post by Gast, and told him that I would be sending the HOPE instructions manual directly to you so that you could post it as you see fit. I've attached a .zip file with the .html file formated instructions. If you extract the files to an empty folder you should be able to view everything as a web-page. It's in your hands now Stefan. I wanted to wait another day until I could have it professionally edited and I also wanted to add a few small details but there should be more than sufficient information for anyone to reproduce my original unit. There are only a limited number of wiring combinations that people can make from the exterior coils to the inputs to the HOPE and/or transformer. I'm HOPEing that everyone will find the best configurations for their specific units with little effort but I'm not to sure how long I may be around to be able to get this out so I've got to act now. My first partner has disappeared from the face of the earth apparently and my other partner has a black SUV with complete with MIB sitting outside his home at this very moment. Considering what is going on I figure that this is better than nothing. If I'm still here tomorrow I will try to update the file to include several typical configurations but I can't promise I will be so here it is my friend. Do with it what you will and God bless.
Best Regards,
Jim
Thank you very much for the upload Jim and Stefan!
Btw: I get fear, if I read Jims remarks! I hope I get him wrong. MIB, black vehicles, ...?? Oh my god! =:-(
Regards Gast
Hi Jim and all,
I had a closer look to your wiring diagramm of your HOPE generator and I guess I now know,
why it is so efficient.
You seem to have invented with the RIGHT wiring a real overunity transformer,
if I am not wrong...
As you have both input coils in series but at the crossed sides, that means,
when the upper right input coils reduces the flux in the right core-leg,
the left lower input coil enhances the flux in the left core-leg.
But because both coils are in series the changing flux will not
require to put more input energy into the coils, cause the
BACK EMF flux changes in the input coils will cancel out.
As the other coils are all in series their drawing of output power
will also not drag down the input coils.
So it seems from my first closer look to be
a very efficient overunity transformer !
Well done.
Regards, Stefan.
Thanks Stefan,
You are correct. Also because the core material is a nanocrystaline material I believe that the resonance field also excites the nanocrystals in the material to generate even more energy. The exterior coils actually collect fluctuations in the field or the core and by routing the energy back into the HOPE unit it increases the output even further. It's a vicous circle basically, but a good one I think, lol. The only tricky part is finding the right places to connect to the exterior pickup coils and where to route it. When using a transformer of the type which I have pictured in the manual, the whole configuration will be different, but even better because then you can run almost any frequency and/or wave type and produce quite a good amount of energy. Although most of the most efficient frequencies will be in a much higher range than if you use the HOPE without a similar transformer. Without the transformer I have been able to light up the tubes as low as 4Hz yes, I said 4Hz. So you know that there is something more going on than just high frequency lighting up the tubes. Anyway, good luck everyone and have fun with it all, I certainly do.
Cheers,
Jim
Hi Jim,
the wiring direction per coil is very important.
Did you wire them all right or left turn ?
If you wire one coil left turn and the next one right turn,
it really is a total different device then, cause the flux is
adding or canceling.
So, how did you wind the coils and how did you
place them ontop the core ?
Are all coils wound into the same direction aroud the core ?
Regards, Stefan.
Here is an updated version from Jim. He writes:
Hi Stefan,
Someone pointed out a couple of goof-ups in the HOPE instructions so I fixed them. I've attached the newer updated version for everyone. I'm sure to be doing this again fairly soon so be prepared, lol. I'll try to find out which way the coils were wraped and placed on the core for you as soon as possible. However I'm not going to disasemble anything until the engineer's get here and help design that amp circuit to provide feedback so we can see if we can achieve a loop in the system. Seems like we should be able to but I'm gonna count my chicken's just yet, lol.
Cheers,
Jim
Hi Jim,
Please can you do the following measurements ?
Take just 60 Hz from an external transformer and feed
this as the input to the HOPE.
Then note the input AC voltage and the input current via
normal AC-60 Hz meters.
Don?t use any load at the output yet.
Write down the input voltage and the input current at 60 hz.
Now get a 10 or 50 or 100 Ohm resistor ( with the right wattage)
and put it into the output.
Now again write down the the input voltage and the input current
and also write down the output voltage across the load resistor and
please send me these values, so we can see, how it works.
Many thanks,
Regards, Stefan.
Hi,
Jim, have you already done the measurements as proposed by Stefan ?
I would really like to see them.
regards,
Markus
Jim said to me, he fried his DVMs and still has to get new ones.
Hopefully he will soon make this test.
Regards, Stefan.
More important is the information about the winding-orientation of the coils!
In Jims last update of the HOPE-Manual I miss this info.
Not that I rebuild this generator already the next days, but this could
be a source of error for a rebuild.
Regards, Gast
PS: Stefan, what do you think?: To get compareable result of voltages on input and output of the HOPE-generator (when it runs on AC feeding with sound) Jim have to rectify the AC to DC and meassure the DC volts/amperes.
This could be helpful to understand the?function of the HOPE generator:
http://www.intalek.com/Index/Projects/Research/Handout3.pdf (http://www.intalek.com/Index/Projects/Research/Handout3.pdf)
Hi Jim and Stephan,
Three questions here :
1) wiring-configuration
2) simple calorimetric test ( also not performed by Jln-Labs )
3) to BushWacker : power-output of your soundcard ?
1)
"Initial Wiring Configuration for the HOPE Generator" above sub-heading : "Step #15".
In this diagramm two violett-Lines from Stereo Audio Output ( right Channel Bare and Left Channel -White)
lead to a connector-point which leads to where ? These connectors are outside the "connector strips"
2) It interesting that JLN-Labs stopped the MEG-Device-Activities at the same point :
Using fluorescent bulbs for Power-Output-Tests. Nothing else happended after this point only vague
statements by Bearden about problems which seem to be unsolvable.
It is not possible to make a clear statement of the effective power flowing into these bulbs, only
estimating by comparing the brightness to normal powered fluorescent bulbs.
The best way would be a thermal-restistor heating up a definite amount (volume) of water in a given
period, measuring the temperature-difference and calculate the power in Joule-Dimension.
I would advice all interested folks to wait until this test or the one Stephan has proposed is performed and prooves
cop > 1. Otherwise a lot of people waste time and money in order to find out later that
they face the same problem as Jln-Labs. This test is a minimum-demand which can be done by the inventor.
Why should a lot of people start building this device all over again ? It exists already and additional testing
does not need that amount of effort than to build 10 new HOPE-Devices.
3) To Jim : What is the poweroutput of your soundcard ?
Kator01
>"In this diagramm two violett-Lines from Stereo Audio Output ( right Channel Bare and Left Channel -White)
>lead to a connector-point which leads to where ? These connectors are outside the "connector strips"
It seems these are the ground lines from both amplifier channels and are tied there together
at this ground shielding plate.
He drives only the upper right and the lower left small coil in SERIES and
this might be the trick, that as the fluxchange is compensating this way the
input coils are not affected by the changing output coils and this no more
power is drawn from the input, when the output changes !
Jim writes:
Hi Stefan,
This latest update on the HOPE assembly instructions is an important update. I am in the middle of building a second unit and found that the 1 inch disc magnets will not work. There would be no room for the primary coils to fit in there proper places if someone were to try and use 1" diameter magnets unless they were to make the output coils spools .50" shorter width-wise. There is a way around this but I don't have the time to write an extended version of the instructions at this time. There are also a few other minor changes. BTW, I tried a small mini amplifier unit that is sold at Radio Shack here in the states, and the feedback from this little thing is enough to kick up the voltage to 180v. I can hardly wait to see what we can do with better amp circuit which is tuned to the proper feedback frequency, but I guess I have to.
Cheers,
Jim
Any news about the HOPE generator ?
Since my questions and the strategy for furhter steps( posted 20.Aug. 90:43:28 h) seem to be not noticed or accepted, I tend to believe that the HOPE suffers the same fate like the MEG.Very sad. We should learn to finish one thing ( especially effective output-tests) before starting new HOPE-Vesions, thus facing new tecnical problems and raising new questions.
By the way it was never said by Bushwalker that this device is a OU-Machine.
Regards Kator01
Any news about Jim,...is he still alive ?
Hmm, any news about the HOPE unit..?
It's a little bit too quite.
Quote from: Nali2001 on October 01, 2005, 08:28:31 PM
Hmm, any news about the HOPE unit..?
It's a little bit too quite.
I have received a couple of private communications from Jim in the past week. He has built a second Hope unit, and made some further modifications, also sent me an image of the thing putting out 390vac @ 880Hz. He is also experiencing some environmental interference (nearby heavy underground construction) which makes the thing a little unpredictable.
What is needed at this point, IMO is a controller device that drives the Hope generator, instead of using the computer soundcard. I have a basic conceptual design for it and have started scoping out parts. The basic components would be a logic device that senses voltage and or current coming out of the unit, that adjusts a variable-frequency oscillator for the optimal resonant frequency. Part of what Jim was finding was the optimal frequency would change from place to place and time to time, so there needs to be a detection and logic circuit that automatically adjusts to the optimal frequency, which would then get passed thru a hi-gain low power amplifier and fed into the Hope generator. The output would I think get rectified and converted to DC, and passed through a high-voltage regulator.
That's my basic idea at this point. This would isolate the unit from any external input (except probably a 9V battery to power the electronics), and regulate the output. Later the electronics could probably be self-powered from a seperate output coil on the hope unit itself.
If there is anyone else interested in developing this design further, I suggest we create a new forum for the Hope Generator, and coordinate our ideas and activities there.
Love and Blessings,
Arinaya
Hello and thanks for the reply.
Hmm you say "390vac @ 880Hz" any data on the amount of watt?
Another thing I'm curious about, does the device 'weakens/eat' the magnet?
And can we expect an updated construction manual or maybe plans about the
radical new version he was talking about, the one that has no resemblance with
the meg anymore (and no longer needs the magnets..?)
Anyway I hope this device does not go down in to silence like so many
other free energy related devices. He was also talking about joining up with
partners/investors what's with that, will he still be making public statement/plans?
Or is he just busy further developing the original design.
I'm very interested in the unit so please don't let it die out.
Thanks,
Steven
I don't have any data on the current or wattage output, but have asked Jim for this and will let you know if I hear anything. A generic soundcard such as he is using puts out no more than 2W RMS, as far as I know. I am not sure how accurate the voltage reading is at 880Hz using a normal multimeter, but with the new unit he is lighting up full-size fluorescent tubes "brighter than I thought they could go", which you certainly can't do with the 1 or 2W of power that a soundcard gives you. I am pretty sure the new unit he has built does not use the magnets, at least I know he has found them unnecessary when using Audio input; also he has eliminated the phone jack from the design and has been experimenting with different placements and windings of the feedback/resonance coils. As for his partnerships I cannot say, but don't think they have gone anywhere productive as yet.
What's interesting is the optimal frequency is fairly sensitive: a difference in fractions of a Hz can cause huge jumps in output voltage. This is not just acting as a transformer, something else is definitely going on. I have suspicions that golden mean harmonics are involved, as the ratio of first and second primary coils is very close to the golden mean (an extra 9 wraps on the smaller coil would pretty much nail it). Obviously this is speculative at this point, but would make sense in light of Dan Winter's theory of extracting electric power from the local gravity well using golden mean recursion, etc.
I am planning on attempting a reproduction of Jim's design with a few modifications aimed at getting more current at the expense of slightly less voltage output. I'd like to use as few high-voltage components as possible while still getting useful power output. Also am planning on rectifying the output to Direct current so that more reliable readings can be taken. At this point I am targeting the design to something like 24vdc with multiple Amps of current (this is typical of a solar panel/deep-cycle battery setup, for example). Time will tell if this is feasible using the present design. Initially I probably will not include the logic circuit mentioned previously, just a simple variable frequency oscillator (manually adjusted) and hi-gain audio amplifier, something comparable to a soundcard, only much simpler, and isolated from any significant source of external power. If the design seems viable I would add in the voltage detection/regulation and automatic frequency adjustment and other goodies that would make this a useable device.
That said, it is going to take me some time to get the funds and materials together, and to find the time to invest in building and tuning the device. I'll try to keep folks informed as there seems to be some interest; if there are others who wish to experiment with this I would definitely be interested in sharing findings, design ideas, etc. Just let me know. If this design is going to go anywhere, it needs community participation; Jim seems to be at the end of his rope, but has given us everything necessary to develop the technology further.
Arinaya
Hello,
Well, you can also light a fluorescent tube by rubbing thin plastic sheets on them. This is of course very low watt.
Damn, if he builds a unit without the magnets... that would be even more amazing. (an over unity transformer)
Is there any clarity on the windings direction yet? Please explain a bit more what type of winding/numbers
of coil would be ideal for golden ratio. Tesla also said (so they say) "To let 2 coils "work" together the must
be of the same mass" (yes mass) It also should be possible to rectify the ac output to dc (capacitor/diode)
and maybe have a more reliable measurement of the voltage/watt.
Is Jim's situation really that bad...? It is really incredible that those independent free energy
inventors/workers seem to suffer somewhat the same fate. I'm glad I don't live in the USA.
What are we goin to do about this...
Steven
500:309 would be pretty darn close to golden mean. I'm not sure if this asymmetrical coil winding plays a huge part or not in the performance of the unit, but I suspect it does, and have a soft spot for the golden mean personally. Jim has indicated to me that he winds the coils all in the same direction, but that he tried winding in opposing directions and it didn't make any difference. I don't really see this as a transformer, as the operative principle is Resonance. You will not understand it if you think of it as a transformer. The mass of the coils does seem to come into play, as the first and second units he has built use different wire gauges and different ranges of resonant frequencies have been observed. He also recently had a "skeptic" perform some tests with a proper RMS meter and an oscilloscope. They measured 0.5 watts of audio input, and 268 watts of electric output. Jim figures that with a better amplifier circuit driving the unit to saturation, a higher input/output ratio will be possible. I agree rectifying or at least regulating the output is one of the next things to do. Please note that neither Jim nor I are calling this a free energy or overunity device, although within the limited scope of conventional theory it might appear as such.
Regards,
Arinaya
Thanks for the fast reply.
Yeah I know... 'free energy' does not exist. There will always be 'a' source (zeropoint/ether/orgon/whatever)
But these are sources we consider 'free'. Although who knows what will happen when the worlds starts using
devices which extract vast amount of energy from the zeropoint/ether field. In my opinion it just might give some
negative results as lowered 'life energy' in the area of the device (presuming that we as living beings also
use the ether field in someway) But if you believe Tom Bearden the Zeropoint field energy is so immensely fierce
that the energy draw of the entire world would be totally laughable.
Could it be that the material of the core itself is very much responsible for the output.
(I don't know if crystal material is actually in the core material) But there might be a connection with
resonance/(harmonic)frequencies and crystals. Also the minute frequencies and vibrations might trigger
the crystal material and correlate to the Casimir effect. So it would be an interesting conclusion if the
HOPE unit would work (to some extend) using standard laminated silicon steel (stator/transformer steel)
or ferrite. (would also be much cheaper than that nanocrystaline material) Although the higher eddy currents
and/or core hysteresis would possibly eliminate the effect.
Are there any strange effect noticed with the HOPE unit like loss in weight or sub ambient operation or glow.
And the generated power, does it have any correlation with time reversed 'cold current' (the non shocking
counterpart of 'normal' current)
Thanks,
Steven
Hi Stefan,
I would like to share information on all of this with the OverUnity forum but have not been able to post there lately. If you don't mind I was wondering if you could post the message below under the topic "HOPE Generator". If you want to file it in the solid state set-up catagory that is fine with me. Sorry for the hassle Stefan, I don't know for sure what the problem is there but I have a fairly good idea and its nothing new.
Thank you Stefan.
Jim
----------------------------------------------------------------------------------------------------------
Hello Group,
I am starting a new conversation under the topic heading "HOPE Generator" so we can keep things in order a little easier. For those of you who have not seen the short video, do not have the instructions manual, or are perhaps not even aware of what the HOPE Generator is you now have the opportunity to find out and obtain whatever information you want.
The HOPE Generator is a completely solid state device which converts resonant frequencies directly into electricity in the form of alternating current (AC). Various geographic locations will determine the prime resonant frequencies that will allow the HOPE unit to operate at its optimum potential. The short video which is available on this forum was created several months ago and is footage of the first unit that was built. The current assembly instructions will allow builders to replicate the original HOPE Generator viewed in the video. There have been a few changes in the last several months having to do with the construction and configuration of the newer model which have proven to boost the output potential by a good margin. There is also more advanced information which can be made available by signing a short non-disclosure document for now and anyone who is truely interested can contact me at (JFauble@sbcglobal.net) for more information. The current input to output ratios of the HOPE Generator are more than 600 to 1 at the moment and more work is being done daily to continue to improve these ratios. I am now looking for serious minded people who truely desire to make this technology available to the world and need help to do this. This technology has fantastic potential but needs to be developed further. It is actually very simple to assemble and not at all complex in comparison to many of the others which are also less productive as far as energy ratios are concerned. If you have any questions please make sure to look over my previous posts so that I am not only repeating myself over and over again. This will help to familiarize you with what is going on and will enable us to make more progress that much sooner. I belive that the HOPE has already proven that OU is possible and we can take it much-much further with the right help.
Best Regards,
James D. Fauble
JFauble@sbcglobal.net
Jim,
will you post here the new design of HOPE without magnets ?
Kator01
Hello Kator,
? ? Thats an easy one to answer. Just remove the magnets from the unit and there you go! Until I had been able to conduct sufficient tests to convince me that I really had something here and had time to apply for an international patent I did not want to let that little trinket out to the general public. I believe that Arinaya is right concerning the golden ratios theory and that there seems to be a fair amount of evidence to show this may be in part responsible for what we are seeing here. One thing to note is that when using a transformer in conjunction with a HOPE Generator it not only changes the optimum frequency range but almost always expands that specific range. Mass has a lot to do with things as well, and if you add or subtract any mass which is connected with any part of the wiring configuration it will change the optimum operating range also. The new unit I built is not connected with any transformer and runs off of the mini-amplifier which is sold at Radio Shack here in the U.S.. Last night I disassembled the first unit and rewound the output coils with 5 seperate layers of Tesla wire. I am no longer using any magnets what-so-ever and have found that the only purpose if any that they serve is to cause the unit to humm or buzz louder. There is absolutely no increase or reduction in the output potential without the magnets installed and therefore as Arinaya has stated, "there is something else going on". I personally believe that the golden ratios or "sacred geometry" etc.., is only part of the answer, and that there is also a kind of piezo effect occuring as a result of the internal ringing of the molecular/atomic structures in the material composite of both the core and also the wire coils. The total mass of a particular configuration also helps to dictate the prime frequency range which a particular unit will operate at. Also, don't forget the discovery that the geological location also has its effect on the optimum frequency range for a given area. What does this tell us guy's? This is just a guess of course but at this time I am thinking that a lot of what Bearden has said is in fact occuring here. I think that it is more visible with the HOPE than it appeared to be with his MEG unit because we are dealing with a more subtle form of energy being input into the HOPE. However if you leave the magnets installed in the HOPE Generator you will not see the obvious changes that you will if you use sound as the resonant input source. Besides the piezo like effect which I believe is occuring initially as a result of the induction by sound it seems possible that by tuning the harmonic reaction within the core we are somehow tapping into the ZPE field. One engineer that I know believes very strongly that there is what he calls phonon activity going on inside the core which he describes as subatomic particles resembling photons but able to move through matter unlike photons. He believes that the exitation of these particles causes them to bounce around similarly to photons in a gas laser, and that these phonons collide with surrounding particles knocking loose electrons from their natural valance's/orbit's. In turn these atoms become unstable and seek equilibrium and draw from the ZPE field. Intersting theory eh? Whatever is happening guys it is easy to reproduce on a constant basis and in my opinion deserves further investigation. The latest measurements of the second HOPE unit were taken by a person who was initially a complete skeptic about my claims. I let him do whatever he wanted to do with the HOPE and he is now a devoted believer! He is now very exited about building his own unit and I have volunteered to help him custom build it to his specifications. I'm not claiming free energy here people, but I've been working in this field for 33+ years to date and have never seen anything as promising as this. I was told recently that it did not require any real power to light fluorescent lights, and that the real test would be if I could light something like xenon bulbs. Well, guess what? The HOPE has no problem lighting xenon bulbs as well. I have also recently plugged a typical 120vAC to 12vDC converter into the HOPE and tuned the audio frequency to both a 60Hz square wave and a sine wave to see if I could run a small DC motor. Guess what guys? It will run all the small DC motors I have even though 60Hz is nowhere near the optimum operating range of the HOPE unit. The audio source was also provided from the crappy sound card in my newer HP Pavilion which is about the worst I've ever heard. Another thing I have found recently is that the quality and/or purity of the tone/frequency makes almost as much difference in output potential as the level of volume/dB's. The skeptics measurements told him that there was a maximum of .50 watts being input to the new HOPE unit and that there was 268 watts coming out at the terminals. The measurement on his Fluke true RMS MM was 122vAC at more than 2.5A of output potential. This is confirmed by the fact that the maximum output of the mini-amplifier circuit from Radio Shack is .50 watts. While a true RMS MM will show the steady voltage a regular MM will show the maximum voltage readings which are exactly 600vAC. These measurements were made without any additional transformers or circuits being connected. Considering the pitiful output of the Radio Shack Mini-Amplifier and the fact that the volume level comes no where near the critical saturation point which I have observed during tests conducted at home it seems obvious to me that another .5 watts might be enough to kill a person. If you don't believe me follow the instructions and build your own unit and try to hold on to the output terminals if you can, lol. There will always be the skeptics but I have a cure for them here. They are always shocked to find out the truth for themselves with this baby, literally!
Best Regards All,
Jim
Hi Jim,
can you run brightly a standard 100 Watts incandescent bulb with it ?
If you can do that from the output of a soundcard,
then indeed you have something.
Could you show this on a video ?
Regards, Stefan.
Hello folks,
I agree on what stephan says.
I have a few extra questions to Bushwalker and people here in Germany,
1) Does any german guy know what the diameter in mm of 24-26 ( sec & prim-pair) ,27, 29 etc gauge wire is ?
2) What is right- or left-channel bare ? Mass-Connection ? When I look a my Audio-Plugs I see only 1 Mass, 1 Left (red) and Right (white), that is tree three wires at all
3) Step 14 :
If for example winding-direction of a 1 set of primary is left to right, is it critical if feed-in-connection for AC is at the left side of coil instead right as in the layout ?
Are Right Channel-Bare and Left Channel white necessary for function in this configuration ?
They dont lead anywhere.
To Bushwalker :
1) Did you triy to feed in pink noise ( audio noise up to 20 KHz )
Energy of noise is mathematically calculated as beeing of infinite value because number of existing frequencies in noise is infinite ?
2) If you have an output of AC 120 V, 2.5 Ampere, why not simply connect a conventional 100 or 200 Watt incandescent-Bulb and proof to community by simple digi-picture ?
This is more convincing than rms-measurements, because you do not know if you have Equal frequency in output as the input-frequency. It could be that you feed in 60 Hz and have higher frequency ( beyond 100 Hz ) output. In this case your Digi-Mulimerter fails.
I personally do measurements with scope across a low-value power-resistor( or bulb which has 40 to 80 Ohm inner resistance)
Then you will measure the hard facts. A incandescent bulb described above would do this
.
I give you here an example, of what happended to me lately :
I have a digi-power-meter ( from a electronic-profil-Lab ). It measures actual Power, reactance, phase shift, Voltage, current etc.
Now I was feeding a AC to AC transformer 230 V to 60 V. With this 60 Volt I fed in half-wave AC ( via one diode and one 1 Ohm-power restistor in series) into a primary of a flyback configuration.
My powermeter at the AC-AC-Transformer indicated 60 Watt while I measured 0.85 Ampere Input-Current to flyback primary with a RMS-Digimeter. When checking with the scope across the 1 Ohm-Resitor I saw the expected half-wave-Sinus-puls 60 Volt peak. This could be maximum of 33 Watt !.
So I measured then 28 Volt true-rms-Voltage across the 1 Ohm with Digimenter
( confirmed by analogue-meter ). An this gave then 28 V x 0.85 A = 23.8 Watt !!
So even profi-lab-instrument have software-errors because thy assume you only
use fullwave-AC. It is even getting worse when you have higher frequencies superimposed as I would expect tjhis to happen in the HOPE-Device.
I call this the measurement-nightmare of which every electronic profi knows about.
So it is my strong advice to do hard testing on a low Ohm-Load.
3) Last Question : How did you get this idea of wiring-configuration ? I assume you had access to some data which are not public. This strange wiring-configuration resembles a complicated band-filter-coupling which is used in high frequency. A normal layman or even specialist cannot get close to such a design by simple trial and error.
Best Regards
Kator
Quote from: Kator01 on October 07, 2005, 09:47:38 AM
1) Does any german guy know what the diameter in mm of 24-26 ( sec & prim-pair) ,27, 29 etc gauge wire is ?
Gucks't Du hier (http://www.export911.com/convert/gauges.htm) (look here).
Bye Markus
Hello Kator01,
I wish I had more time to answer every question that I am asked these days but I honestly do not have that kind of leisure at the moment. The HOPE is just one of more than a dozen projects which I am involved with right now and work is piling up quickly. The only reason that I felt obligated to post the initial information on the HOPE Generator was because first off, I knew Stefan before he ever started this forum as someone with integrity and that he is an exceptionally intelligent and kind person. Secondly, because of inside information that I have had access to in the past concerning the NWO elite's game plan to take control of the globe and basically put their personal brand on every living soul on the planet I felt it was of the utmost importance that anything related to alternative and/or possibly free clean energy technologies should be shared with people immediately. Since the HOPE is only a few months old at best I have not been able to do nearly as much as I would like with it. As I have said many times before, I believe that there is very possibly great potential to develop an impressive AE or even FE technology with the right help and backing. There is only so much one person can do, especially when that person is in the kind of position that I have been in now for many years. I am not claiming free anything here, but only chose to offer this information in HOPE's that something might develop as a result. I cannot keep up with all that I have on my plate right now and so I leave it up to the so-called experts to file or forget the information that I have been able to offer thus far. I do not consider myself an expert in electrical engineering and am only a garage tinkerer basically. I do understand the many questions that I am asked however I am finding it exasperating to have to answer so many of the same questions over and over and I simply do not have the time anymore. However I will continue to work on this and the many other projects I am currently involved with and report any new or important findings to the appropriate channels as time allows. My suggestion to those who see the information which I have reported as important is to follow the step-by-step directions that I have written out for you and try to help find some answers for yourself. One quick note I should telll you Kator is that the stereo cable hook-up should actually read audio/video cable. Thats the four wire cable that you use to plug a TV into a VCR or DVD player. I hope that I can find the time to edit that in the HOPE instruction manual soon but I can't promise anymore at this time. I do want to help people, but until I receive some help myself some things will just have to wait. Sorry for the goof there guys.
Cheers,
Jim
NWO elite game ?
I do not know about your information sources,pardon me,
but people,who think that he/she/they would be "alternativeless"-
shall know that we are also MEMBER of the APOLLO/PYTHIA Party,
so we will ever stay for an empirical "DECATHLON"!
"MOEGE DER/DIE/DAS BESTE GEWINNEN !"
Virtual "DELPHI GAMES" ? ALLZEIT BEREIT !
SIMON/SENSO LEVEL:38
SPACE CADETT:ADMIRAL
Lanca lll,
Yes, I'm sure thats what you've been told. And no, I will not tell you where I got my information. I do believe that you really are a "Space Cadet" though, lol.
ZIEG HEIL!
Bush Wacker
Would such guys like "Adolf" know something about our intention they would go "freiwillig"
to the "Zyklon-B-Berieselung" !
We have got the "Tools" and there is a great "anonym" army.
Dear world,beware !
Would you please stop using nazi experessions and comparisons !
This is a science forum.
Markus,I agree 100% .
But if you are informated,this are not "nazi" expressions or comparisions.
"Zyklon-B"=IG FARBEN Versuchs- Experiment(Ex-Hoechst(Aventis),Bayer,BASF),but used by NAZIS.
This had been my answer to the (pardon,so often heard) Black-Shadow-Conspiracy/
WELTVERSCHWOERUNG etc. and to his "Zieg Heil!" -joke/provocation,and this is 100% NAZI-EXPRESSION.(Probably 1Liter" Zieg"-en Milch" Heil"-t him!Ex oder nix !)
I am living in Portugal,where the population has got +/- 80%"great jewish-family-genes"
my mother is naturally from here (Beja),my father from Hannover and I :
Casablanca/Maroc/Africa
I respect this science forum ,but science is the tool for projections,
with best/worst case scenarios.
Mister Bush Wacker,
there is a great open/public conspiracy in form of the
US2813242
US3398370
patents of an inventor called Lloyd Crump,work for the US Government
and publicated.
Harmonic waves=Pythagoras
Resonance: e=hXv Plancksche Transformation (do you sometimes use a vocoder/echo hall ?)
For anyone interested in building the HOPE, the cores are on backorder until the end of November. I placed the order and will see what happens.
Rich
Does anybody know where I can get these cores in Europe/Germany ?
Maybe we should make one big order to get a better price.
I asked the sales rep about other sources and she said there are only two places in the U.S with these cores. They are back ordered due to demand, so a cheaper price may be hard to come by.....
Rich
In about 2 month I have a little time to do a replication of the HOPE.
Maybe you can order me two cores and them send them to Germany.
How much are they ? Does the company have a website ?
I hope they are not fragile... otherwise I might receive them in little pieces.
It would probably be faster for you to call directly, as I did not find a way to place the order on line. The core is $99 U.S.D. plus shipping. If you have trouble I'll certainly be glad to help you out.
Elna Magnetics
800-553-2870
Rich
Folks,
I wonder if you have read my latest post where I cornered this Mr. Bushwacker. This hope is a very efficient step-up-converter with two phaseshift-Coils. With teh resulting High-Voltage and an input of 1 Watt you can easily light up
neon-tubes. But this does not mean that you get any more power out. If I consider the time he used for all his postings here and compare it to the 5 minutes of testing the HOPE with two 230 Volt incandescent-lamps and give proofe to the community I cannot help but regard him a desinformation agent. Do not let your time, energy and money be consumed up by a device which is a well known technique among electronic- enginners.
He is not able to do this 5 minute test.
So why do you waste your energy, eh ?
Kator01
I agree to a point, but if you can light 4 neon tubes with 1 watt then isn't that highly effecient in itself? Why don't the engineers use this technology in the light ballasts to save millions of watt hours on the grid? He did state the "skeptic" used an oscope for his measurements, that's what really peaked my curiousity.......
Rich
@ Kator01
I?m not really sure but I believe neon tubs like Jim used them have an efficience of about 40% using 60Hz sine wave input.
Which means even if the HOPE is a perfect power supply for neon tubes you would need several dozen watts to light them to full bright. I really doubt you can do that with one or two watts of power input,...i really do!
But prove me wrong if you can.
Otherwise it would be like oouthere? said: Why aren?t we using the HV and the waveform of the HOPE to power neon tubes if it is that efficient ?
Jim also said he had a sceptic (electrical engineer ?) to measure the output and even he with his professional measurement equipment had to confirm the overunity effect.
"...This hope is a very efficient step-up-converter with two phaseshift-Coils...." - Yes, maybe the setup is known among electronic- engineers. But surely not with the nanocrystalline core which plays a key role in the process.
Kator01 why do you insist on a 5 minutes test ?
I don?t suppose there is a another time dependent process which will kill the overunity effect after a short while, although I saw this happen with other "OU" devices.
But it would be possible, I agree.
To Rich and Markus,
why these step-up-converters are not used for neons is very simple : enonomic, would you use a 100 ?-Core vor cheap Neons ? Ther is no interest for saving money in energy-mangement.
The technique could be used but too costy.
You can light up more than one neon with 1 Watt, but light-Intensitiy is diffent to if you power it with normal powering-technique. Jim showed on the video on one or two small 8 Watt Neons
Frankly, I dont believe him anymore. He presentet toomany contradictions.When asked specific technical questions he escapes stating that he is not an expert. He states that he is not claim free energy at the same time saying that he has
measurement of 600 : 1 proved by a rms-Meter. He said it is 400 Herz Output, but rms-meters are tune to 50 Hz. Se my on measurement-nightmare.
I believe ih is just a poor guy beeing used as an agemnt by what he calls the NWO-Conspiracy. The USA have a special
desinformatio-dept, and infiltrate every forum. I can not understand why people are so gullible to believe all that HOPE-Stuff. Loo at how he introduced himself and now he cannot give proof by a simple hard-test. I have mre than 25 years of experinece with this desinfo-stuff and today I look at the overall pattern of a person whe it shows up and does calims like this.
Save your energy, folks
I will not argue any more but will post afgain and again in order inhibit damage in teh community.
Kator01
@ Kator01
Quotewhy these step-up-converters are not used for neons is very simple : enonomic, would you use a 100 ?-Core vor cheap Neons ? Ther is no interest for saving money in energy-mangement.
- Why should the energy-management not be interested in saving money ?
- I agree with you that it doesn?t make sense for a single neon. But it you have a big store with hundreds of neons and you would use one big Hope device to power them it would definitely make sense.
QuoteThe technique could be used but too costy.
- See above.
- To recreate the wave form and frequency the Hope gives out you can also use other circuits (electronics with timer ICs etc.). It wouldn`t be necessary to use this expensive nanocrystalline core. But I think it is the most important part of the device as there might occur some kind of tabbing into ZPE. If YOUR theory is correct, then it should be possible to light up the neons as shown by Jim using a normal core, too.
-That would be really interesting to know.? ?
QuoteYou can light up more than one neon with 1 Watt, but light-Intensitiy is diffent to if you power it with normal powering-technique. Jim showed on the video on one or two small 8 Watt Neons
- What do you mean "light-Intensitiy is diffent" ? Is it brighter with the Hope ?
QuoteFrankly, I dont believe him anymore. He presentet toomany contradictions.When asked specific technical questions he escapes stating that he is not an expert.
- He?s only honest. I mean he even tried to find people who are skilled enough to give us reliable information.
QuoteHe states that he is not claim free energy at the same time saying that he has
measurement of 600 : 1 proved by a rms-Meter.
He said it is 400 Herz Output, but rms-meters are tune to 50 Hz. Se my on measurement-nightmare.
- It depends on definition what is understood by free energy. Wind and solar are free energy, too. The Hope device costs money to build and if it really tabs into ZPE we are just converting it into electricity. No one knows what could happen if we weaken this energy potential.
I agree that 50Hz meters will give you wrong values with 400Hz but as he said even sceptical guys had to admit the "plus" of energy.
You also have to understand that he is risking his reputation if he would claim overunity immediately. It is much better to wait until the first working replications come out. You can be sure that only a few of those who try to replicate it will have success and the failures will be first to claim it doesn?t work although they made a mistake.
QuoteI believe ih is just a poor guy beeing used as an agemnt by what he calls the NWO-Conspiracy. The USA have a special
desinformatio-dept, and infiltrate every forum. I can not understand why people are so gullible to believe all that HOPE-Stuff. Loo at how he introduced himself and now he cannot give proof by a simple hard-test. I have mre than 25 years of experinece with this desinfo-stuff and today I look at the overall pattern of a person whe it shows up and does calims like this.
- I would suggest you try to visit Jim to see what is going on.
- I don?t believe that he invests his time and money for something he knows doesn?t work.
Kator01, I appreciate what you are doing as I feel the same. We have such limited resources inwhich to conduct our experiments that they must be marshalled in the most promising and effecient manner. A picture of a HOPE powered 50w bulb next to a 50w commercially powered bulb would be enough to convince practically anyone.
The next project was to be a Kromrey convertor but I can't seem to get a response from John Bedini on what the necessary changes are from the original patent to make it work. As stated before, limited resources......
BushWacker, please post a picture of of the light bulb test using any incandescent bulb 50 watts or greater and everyone can appreciate the HOPE.
Thanks,
Rich
For Markus,
if you insist that the Hope might be a working device, I will help you with the following adress since the AC 320 Core is not available. I once had a meeting with a technician orf magnetec Dr. Martin Ferch, mail: martin.ferch@magnetec.de.
Web : http://www.magnetec.de/magnetec.htm
I hpte that this man is still working there. It was 4 years ago.
They are producing nano-cores.
I agree that you can replicate the Hope-effect ( whatever it might be ) with other Hf-Cores.
So you have a look to this website and maybe you find a simlar core-material
Regards
Kator01
dtv-Atlas zur Physik,Band 2,Seite 285
Tesla-Transformator,entwickelt 1892 von NIKOLA TESLA(1856-1943):
Die Primaerspule ist Teil eines elektr. Hochfrequenz-Schwingkreise... mit Kondensator und
Funkenstrecke. ...
Die Sekundaerspule erzeugt in ihrer Naehe ein elektr. Hochfrequenzfeld.
Beweis: Zuleitungsfreie Neonroehren in der Umgebung leuchten auf. ...
Diathermie
Markus,Minimalansprueche an wissenschaftlicher Kenntnis sollten gelten !!!
@ lanca III
Welchen Markus meinst Du damit ?
Es gibt mehrere.
Folks,
I have taken the time to draw a simple diagramm, see attachment.AC in is blue path, Out is red-path.
Prim1-1 drives sec2. prim2-2 drives sec1.
Green coils do phaseshift on the secondaries so that there is a 180-deg time -delay between both output-signals, called push-pull-output.
Nothing extraordinary but very effective, can be up to 98 % efficient of step-up-voltage and output-power.
Regards
Kator01
An Markus !
Vor circa zehn Jahren erfolgte der kommerzielle Versuch der
Markteinfuehrung einer Diathermie-Heizung,Entwickler:Ex-DDR-Buerger
Name:Dr. Helmut Reichelt
Objektbezeichnung:Thermotexx
Technische Basis:DD286012 Elektronengas-Kreisprozess wobei Strahlungs-und Waermeenergie
zu Elektroenergie transformiert wird.(Patentpublikation vollstaendig in Haenden Dr.H.Reichelts)
In der DD287597-Publikation wird eine Graphit-/kohle-Thermovoltaic-Zelle beschrieben,welche mit
demselben Kreisprozess ausgestattet ist.
Angegebene Umwandlungs-Effizienz: bis zu 97% (entspricht dem Wert der Lorentz-Transformation).
Es waere recht hilfreich,wuerden Sie den Herrn Doktor Helmut Reichelt dazu bewegen koennen,
die DD286012-Publikation zu Veroeffentlichen ! (wohnhaft in der Umgebung Dresdens,haehere Info
(dpma,neueste Patente:Adresse + Telefonbuch.de)
Hi All,
Unfortunately I have not learned how to read/speak German and so have not been able to understand the conversation lately. However I am attaching a new diagram of a simplified configuration for a HOPE Generator. You can also visit the links below to view information about the material characteristics of the cores that I have used for the HOPE. Remember that in order to replicate the HOPE correctly you will need to use the same materials otherwise the outcome will of course be different. I have decided to hold off posting more information until I am able to employ the help of a good engineer in order to avoid any further questioning of my integrity. I am NOT a professional electrical engineer and although I have a fairly good understanding of general physics and old school electronics I am not keen on designing much of the microcircuitry which I have been asked to build. I do find it interesting that in the weeks since I have recommended either the AMCC 320 Powerlite core or the AMCC 1000 core for builders to use both U.S., companies which distribute these cores have decided that they will soon be requiring a minimum order of 300 cores. This will soon make it very difficult for others to verify anything. The same thing happened with the quadrupole ring magnets when I gave out the instructions for building an Ion Source Beam Projector and this seems to be a common tactic to prevent the average person from developing any possible new technologies relating to energy or medical applications. Since the price for a single core is much higher than the per core price for a bulk order it makes me wonder if this recent policy change is soley the idea of the distributors? Oh well, probably just one more coincidence right?
http://www.metglas.com/index.asp
http://www.elnamagnetics.com/
http://www.elnamagnetics.com/metglasdrawings
Cheers All,
Jim
Erg?nzenden Infos zu lanka III - post :
Die Internetwaybackmaschine ergabe mehere Eintr?ge, alle jedoch mit folgendem Inhalt, die auch den Ansprechpartner nennt :
Aus rechtlichen Gr?nden k?nnen wir Ihnen leider die Web-Seite
Dr. Reichelt Thermotexx-
Fl?chenheizung 300
Wir bringen Sonnenw?rme in Ihr Haus,
f?r Information ?ber dieses revolution?re Heizsystem nicht mehr zur Verf?gung stellen.
Bis zur Kl?rung dieser Situation (und neuer Adresse) erreichen Sie uns unter:
Tel.: 03693-875061 oder Fax.: 03693-875062
Ansprechpartner: Herr Blaufu?
Kator01
Hallo,
hier nun noch eine Info von Dr.Vogelsang, weitere Recherchen sind also sinnlos :
Quelle :
http://www.eurotinnitus.com/phpBB3/viewtopic.php?p=703&sid=8b18f70b90993e94a25f7fc487a2bccf
Dr. Vogelsang, 14.07.05
Niemand wei?, wann die ?lvorr?te der Erde ersch?pft sind, sondern die meisten schreiben voneinander ab. Die allgemein unterstellten Zahlen, sie w?rden noch zwei bis drei Jahrzehnte reichen, k?nnen falsch sein. Dann allerdings fragt sich, warum eine schwarz-gelbe Bundesregierung mit dem US-Regime in den Krieg ziehen will. Die US-Politik geht auf Nummer Sicher: Sie okkupiert einen ?lstaat nach dem anderen und k?nnte dann die von der Max-Planck-Gesellschaft geforderte Bev?lkerungsreduktion auf nur noch eine Milliarde Menschen durchf?hren.
Dies ist unn?tig angesichts der praktisch unendlichen erneuerbaren Ressourcen. Hier ein Beispiel:
Die ?Dr. Reichelt Thermotexx Fl?chenheizung 300? heizt 20 m? Wohnfl?che mit 40 Watt.
Gepr?ftes Patent erteilt unter der Nr. EP 0 777 524 B1 1998.
Bericht in ?raum&zeit?, Nr. 102/1999. (raum&zeit, Geltingerstr. 14e, D - 83623 Dietramszell , www.raum-und-zeit.com , email: redaktion@ehlersverlag.de
Das Prinzip ist die Eigenschwingung, in die der Bewohner mit seiner K?rperw?rme eine Folie versetzt. Diese Eigenschwingung wird durch kosmische Kr?fte verst?rkt.
Ein US-Konzern jedoch hat die Erfindung gekauft und h?lt sie dem Markt fern.
Kator
Ein Herr Hermann Oster (WO2004051149) will einen aehnlichen Flaechen-/Kaltstrahler
voraussichtlich 2006 (Technische Probleme sind noch zu loesen)auf den Markt bringen,
der Energiebedarf -per qm Grundflaeche-ca. 40Watt,bei "normaler" Daemmung.
Heizungspreis wird-bei 80 qm Wohnraum- mit ungefaehr 3000 Euros angegeben.
Mir geht es jedoch nicht um die Heizung, sondern um den EM-Kreisprozess,welcher insbesondere
als System fuer low cost "Solar-/Thermik(Raumabkuehlung)-Zellen/Tapeten global interessant ist.
Die Publikation DE3213977 gibt naehere technische Erlaeuterungen.
Die genaue Adresse des Herrn Dr. Helmut Reichelt:01744 Reichstaedt-Dippoldiswalde
Neue Siedlung 22A Tel.:03504....
("Er" ist ein aelterer Herr und laut einem Hr.Oster ein "GENIE",also behutsam "anklopfen"!)
? Hi BushWacker,
? We're not doubting your integrity, so please continue to post.? Looking over the last drawing, the top left and bottom right coils are not wired?? They appear to be jumpered to each other on one side and open on the other.? Is this the correct wiring?
? Thanks,
? Rich
Hi Rich,
Thank you for your vote of confidence. I don't get a lot of positive feedback and it is always encouraging when I do. The question you asked concerning the wiring configuration has been a popular one lately. This is in fact the correct wiring configuration and I understand the strangeness of this. There are a great many strange anomalies that I am discovering just about every week. Standard electrical theory does not necessarily seem to apply at first glance when working with the HOPE Gen.. Another thing I discovered just yesterday was that one single wind/wrap of thick aluminum wire induced a higher voltage than 1200 winds/wraps of 29 gauge tesla/magnet wire. It appears that mass and the elemental properties of specific materials have more to do with the output potential than we are used to seeing with standard electronics. The actual material and mass of the induction coils seems to be more important than any number of winds/wraps, and the materials ability to conduct sound seems to have more to do with the reaction in the core and the energy produced than any electromagnetic properties of the induction coils. It may have something to do with the difference in the relaxation times of the various materials but this is still somewhat up in the air. I am currently experimenting with different combinations of materials to try and nail down some more answers but things are going much slower than I would like. I'm wondering if something like (Indium wire) might increase the transfer of the audio signal and increase the resonance in the core and coils. As time continues to pass it is looking more and more like we are dealing with something other than mere electromagnetic fields here and that there is some kind of exchange going on with the alleged ZPE field or at least some kind of atmospheric energy. The excess energy which is being produced must be coming from somewhere and so as of now I have no other explanation. I had a great many doubts about Tom Bearden's theories a year ago but am beginning to seriously wonder if he is in fact correct about this alleged Zero Point Energy thing. Regardless, we still have a long way to go and a lot of work to do before we are able to answer all the questions about everything we are seeing here. I will be speaking with an attorney this evening to work out some details involving the patent application for HOPE technologies and we expect to have the application filed within the next few days. HOPEfully we can then show this stuff to prospective investors and receive the funding necessary to put things on a fast track. Right now all we have for certain is economical lighting capabilities but we believe that this is only the very tip of the iceburg s-t-s. With the amount of interference and direct harassment that we are experiencing it seems to me that we must be on to something much more here.
Best Regards,
Jim
Bingo,Bushwacker !
We are in the 4Dimension and this little Particles with wich we are working do not want to be mandated !(Heisenberg tried to do this-he failed!)
How many Paameters do you think we have to combinate ?
Sub-/Electron-Sphere,multiple-spin-magnetism,gravity etc.!
Hello Lanca lll,
I won't even try to pretend to know the answers to these kinds of questions. I am not an expert in physics and engineering. However I do know someone who could probably answer many of these questions and will ask him if he would be willing to right up a thesis if he can find the time. I can't promise anything there either though since he is now working long hours on the graveyard shift as they call it here. He has written numerous books on theoretical physics which goes far beyond conventional physics at this time, and I believe he may be right on a lot of things. I will also ask him if he will allow me to make some of this information available to this group if you would be interested.
Cheers,
BushWacker
I've been creating a 3D model of the Hope Generator using AutoCad 2006. I'm kind of a newb, but I finally figured out how to use it. ;D Currently I have the core, with the four smaller coils done. I'm at work right now, so I'll post some previews when I get home. Hopefully they will be of some use to help people construct the HOPE generator. I downloaded the Schematics for the PowerLite 320 C Core, and found that some of your measurements in your tutorial were a little off. :-\ I'll let you know of any descrepencies that I found, once I'm done with the two larger coils. After that I'll try to represent the wiring configuration.
BushWacker: I know ur busy, but I'd love to see some pics of regular light bulbs lit up!
Jin
Hi Jin,
Thanks for counting the HOPE worthy of your time and effort. Although there is obviously much work to be done before we see the ultimate in design for this kind of technology I do believe that the current model shows good reason for study. I am attaching the spec .pdf for the AMCC-320 C-core for your reference purposes in case you may find it handy. I also wish that I could show you pics of the current model lighting typical incandecent bulbs however circuitry will need to be designed and implemented for this to be possible. The type of energy being produced by the HOPE is not the typical current we are all familiar with and when you look at the purple streamers sprouting from the filament of a small incandecent bulb and trailing out to the edges of the bulb it appears to be some type of plasma. The HOPE Generator never becomes even slightly warm even when it has reached several thousands of volts and has run for hours on end. I've heard stories of cold or cool electricity from Tesla's research but until now I had never seen it. It will however burn components and such and I've burned out more than my fair share of sound sources. For this reason you will want to buy a miniature audio transformer to install in line between the HOPE and your sound source. I'm only putting in a maximum of .5 watts from the mini amplifier amp circuit I purchased at Radio Shack and have not had any more high voltage feedback so far but you might consider being cautious about this if you are planning to input any more than .5 watts. If so you may need a more rugged audio transformer than the little bugger sold at Radio shack. Well, gotta get back to the grinding stone s-t-s. Thanks again for your contributions and keep in touch okay? If you have any questions or need any pointers let me know.
Cheers,
Jim
I agree with the comments of Kator01 on 11 October. I think that we should be on our guard for people using this forum to spread misinformation. Think about it. If you were the US government and you wanted to discourage civillian engineers from developing overunity technology you might instruct your agents to post bogus plans to websites like this.
What first aroused my suspicions was Jim?s comments in August to the effect that the US government had persecuted him for the last 30 years thus preventing him from achieving anything. In my experience it is the con artists and hoaxers who talk most about suppression. I know of two occassions when those who made such claims were caught out lying. Those like Shoulders, Santilli and Mills who may really have something worth suppresing NEVER talk about suppression. I have to admit he does sound 100% sincere but then so did Carl Cella yet his water-car plans turned out to be a hoax. The text with the plans so oozed sincerity that I was completely fooled but at least I did not spend $2000 trying to reproduce them like some-else in these forums.
If Jim was really so concerned about interference from Big Brother then why does he post such material under his real name? If I was going to be the first to throw a spanner into the works of US capitalism I would be very careful to conceal my identity. Maybe Plaubel is not his real name but then why provide a surname at all?
Even more suspicious is the fact that he actually admits to having contacts in the US government?s intelligence community. For instance In his June 27 post he states ?I have not found anyone else willing to help except for a guy in town here who just happens to be a reconisance (sic) expert for the U.S., Office of Homeland Security?. In his August 09 post he writes: ?I have some friend's in some of these agencies also, and a few of these guy's have visited me in person throughout the years to let me know first hand what has been going on? and ?The only reason that I am still here is because of the many good guy's in within some of our agencies who have been watching my back?. He goes even further in admitting to have been an agent of the US intelligence services himself in the same post when he writes ?I worked at the information center of a great number of black projects for about 5 years until I finally turned in my resignation due to a matter of my own conscience? IT COULDN?T BE CLEARER THAN THAT.
In his June 27 post he tries to enhance his credibility by stating ?I come from a background of working for the U.S., DoD at the center of many black projects which were well above top secret?. Such a position would require one to have an engineering degree one would think yet in his October 07 post he states ?I do not consider myself an expert in electrical engineering and am only a garage tinkerer basically?. I see a possible parallel here with the UFOlogists who are recruited as agents of the US intelligence services with the promise of privilidged access to classified information but what they are really getting is misinformation.
In Jim?s August 08 post he states ?A small group of private investor's want to take a look at the device and are flying the best engineer they know of to El Paso in about six weeks as things look now?. Naturally such a consortium would want to see patent protection so we read in the October 21 post ?I will be speaking with an attorney this evening to work out some details involving the patent application for HOPE technologies?. I wonder how he reconciles these plans for comercialization with the distribution of the plans on the internet? Maybe the fact he is going to withhold certain ?trade secrets? from the open source plans means that they will not invalidate his patent applications. You can bet your bottom dollar that these ?trade secrets? will be required to make the damn thing work.
I could go on about the absurdities and contradictions in jim?s technical descriptions of the HOPE device but I shall leave that to another post.
FreedomFuel,
If anyone sounds like a quack it is you! You have mis-quoted me and obviously mis-understood me as well. However for those who doubt my sincerity and truthfulness concerning any information that I have given or coments that I have made it is their right to have their own opinion. I have never told anyone that I had worked as an engineer for the DoD. I was an informations/publications specialist not an engineer. I do not blame anyone for reserving doubts about people who have been shown to be untruthful or who make claims that they cannot back up. You however are simply trying to trash my name without knowing the first thing about me. You are obviously not a scientifically minded individual because your assumptions about everything prove that out. It is because of people such as yourself that more sincere people are afraid to speak out. Your comments do not offend me since they only show your own ignorance and lazyness. You have obviously never assembled a HOPE Generator or you would not be trying to defame me by your foolish assumtions and comments. You have obviously never done a background check on me because you would not be calling me a liar. You know absolutely nothing at all about me other than what information I have given freely to try and contribute to the knowledge base of alternative energy technologies. There is an aweful lot that I have not told anyone in these kinds of forums for the very reason that there are to many people like you who will try and tear anyone appart who may try to speak out. From my experience I have learned that those who devote their time to defaming those who try to provide information on possible alternative energy technologies are either associated with major corporations, government entities, or are simply ignorant and/or mean spirited. If I have lied about anything then it should be proven before my name is trashed for being a liar. I challenge you to do a background check on my employment history, talk to some witnesses, build a HOPE Generator according to the instructions I have provided, or at least shut the hell up until you have some good reason to trash me like you have been doing. Your tactics will not detour me from my mission nor will you discourage me from moving forward to at least try and develop these types of technologies. If you are doing "Bitchwork" for some U.S., agency forget it! If you are simply a mean spirited person who has lost all hope, I have HOPE to give you, and you are only beating your head against a brick wall by thinking that your words will serve any purpose. I do not need you or anyone else to assist me in proving anything to anyone. The proof is in the pudding as the saying goes, and until you have done your homework you should not be trying to put me to the test! I know exactly what I am doing by providing the information for the basic HOPE design on the Internet. If you understood both the U.S., and International patent laws you might be able to understand the logic of my actions. By putting the information out there on the Internet I have already secured my rights to intellectual property for this invention in the states, and that is why I have just filed the "International Patent Applications Forms" for the HOPE Generator this last week. I could tell you of the difficulties and obstructions which were employed to try and prevent me from being able to do this but you would only call me a liar again. I have proof of every word I say, and I have numerous witnesses to every event I might have mentioned in case anyone wishes to challenge my integrity and this includes you FreedomFuel. If I was a liar I would be fearful of giving my real name. BTW, what is your real name? Whoever you are you sound extremely insecure, and it seems obvious that you know very little if anything about the way anything really works. I suggest that until you do learn about the real world that you abstain from defaming people or technologies that you know nothing about. It only makes you look like a complete jerk!
Most Sincerely,
Jim
Hi there,
it is almost very interesting, Jim :
With no word freedomfuel ever stated that you are a liar. He simply put together your own statements to show the pattern which I could see also along the course of this discussion. It is obvious that the pattern itself raises doubt. No one here should fall into the trap of beeing so gullible to spent time and money for a uncomplete presentation especially if I look at your last post where you claimed just using one simgle turn of Aluminium-Wire delivering more output-power than 500 turns of cupper-wire. It is getting more and more absurd.
You are shouting at your own statements, you are attacking yourself.
Just give the community this simple proof of one or two 100Watt incandescent bulbs light up by the hope. No one can repeat the experiment since the core - as I remember from some past statemenst here - is not available. So what do you expect should people do here, eh ? They wait for proof not for big stories which need more time to write and to read that doing this simple test.
Kator
Kator01,
I believe it is quite obvious to most what FreedomFuel is implying by his comments concerning me. If you can understand English it should be hard to deny that nearly every other sentence is characterizing me as being a fraud, liar, hoaxter, etc.., etc.. . I am not attacking anyone, but I do feel compelled to try and defend myself against such comments which are quite apparently directed in order to defame my character and integrity. In the CIA and corporate/military sectors these kinds of tactics are termed "Bitchwork". Please do not assume that I am implying that this person could possibly be intelligent enough to land a job in one of these sectors as I am not. As far as reproducing the original HOPE unit goes, I do not recall telling anyone that these cores were unobtainable and nobody ever even asked me. I am extremely tired of the assumptions and attacks of certain mean spirited individuals who seem to have nothing positive to offer anyone. These people contribute nothing yet seem to have excess energy to cause mischief and chaos in the AE/FE forums. I suppose that there is a very slim chance that I could have somehow miraculously hit upon the ultimate design for HOPE technologies on the very first attempt? However considering the odds against this happening I tend to believe that further investigation is waranted. It appears that you are attempting to defend the behavior and/or comments of FreedomFuel and that you are of like mind in your thinking. Please do not insult my intelligence with such lame attempts to defend such obvious attacks upon my character because I simply do not buy it Kator01! If neither of you percieve any value in the discovery that materials other than quarts crystals react to resonant frequencies to produce electrical potential then why don't you simply move on rather than attempt to harass me and waste my valuable time? Fact is Kator01, I have spoken with at least 6 individuals who have ordered PowerLite cores and are planning to reproduce the original HOPE design. These people will have my full attention and they will be successful if they follow my directions. The international patent for HOPE technologies has now been applied for and it will now be up to the patent department to determine whether this patent will be granted. Whether it is or isn't makes no difference to me because I have done my part in the process. I have spent a good deal of money to get to this point yet I have not asked anyone for a single penny. All the information including assembly instructions was given for free and I have not made a single penny from all of the time and labor and money that I have put into all of this. What the hell have you or FreedomFuel done besides trash and harass people who are trying to contribute something to this world? I feel sorry for both your pitiful souls. If you want your wishes granted try rubbing a magic lamp. Otherwise get off your fat A's and do something besides attempting to harass and belittle me. You are simply wasting your time!
Get a life!
Jim
I agree Jim,
i will not waste my time with this any longer. Three persons in this community have asked
you to give proof and even showed you the way how to do it.
The intersting thing is that since more that two month you avoid by all means to give it.
By this you would proof your integrity, not by words. There is a german saying :
"Die Hoffnung stirbt als letztes"
Exact translation which also fits in a poetic way :
"Hope dies last." or "The last thing which dies is hope"
We have passed this stage anyway.
Regards
Kator
I have been perfectly honest up up front about where things stand with the HOPE generator at this point. I have said on several occassions that I am NOT able to light standard incandescent bulbs yet due to the nature of the type of energy coming from this device. If you cannot understand this and are only interested if I can light incandescent bulbs then you will have to wait until I am able to find the right circuitry to make that possible. There is also a saying that goes, "All good things take time". If you think that a finished marketable technology should only take 3 months to perfect then you are living in a fantasy world. I do not feel it is my responsibility to cator to your particular wishe's or wim's and at this point if I could light a dozen incandescents with a single little HOPE unit I would not give you the time of day let alone any further information than I have. The unit is going to the engineering department now for the purpose of increasing the output and HOPEfully designing proper circuitry to convert the plasma like energy to usable standard type current, however in order to learn anything further you will have to purchase the technology from here on out. For those people who have not treated me as though I am their enemy I will continue to offer all information freely. It is clear that there will always be ignorant and nasty individuals who will bite their nose to spite their own face however I will not cator to such people's wim's. You can continue to say what you will about me but it will not detour me from trying to develop these kinds of technologies. For the rest of you out there who wish to get inot this area of research let these guys be an example of the kinds of idiots that you will have to deal with. Personally I do not believe that a little over 2 months is that long a time to expect a new discovery to take to get developed to the point that certain individuals think it should be but their are all kinds of opinions out there aren't there? If and when I do make any considerable advances with this technology I will let you all know through some of the more rational and logical people that I have met in this forum. Those of you who are building your own HOPE units may contact me at any time and I will do my best to help in any way I can. I've made quite a bit of progress considering the short time since this discovery but be advised that not everything is instantly perfected and these kinds of things do take time and considerable patience as you can no doubt see. I have partnered with several highly qualified individuals and we have just finished filing the legal papers for our new company. I cannot give an exact time frame in which we can expect to have anything developed to the point that it is market ready s-t-s and there is a lot that needs to be done to reach that point. We are not slacking on this venture and things are moving forward. Other than the very few individuals who seem to have their heads up their butts s-t-s everything is looking extremely positive. I appologize for any misunderstandings in the translation from English to German etc.., but I have tried to be as clear and honest as possible with you all. From this point on I will only be relaying information through those people who have respected my intentions and character so that I can use my time in a more productive way in order to further the development of these types of technologies. I challenge you all to do your homework and even check into peoples backgrounds before labling them through mere ignorant assumptions. Also, do not let such people detour you from doing what you know is right.
Best Regards All,
Jim
James D. Fauble
:o Come on guys, this is a scientific forum, not a cat fight on who is right and who is lying! :o
Kator1 and Freedomfuel are right to question the validity of this project, but they were pretty harsh in expressing their opinions.
BushWacker: As I'm sure you know, many people have been decieved by projects such as these, so you will naturally encounter more skepticism than usual.
Just about everything has been said about the validity of several statements made by BushWacker. Therefore, no more discussions on that topic should be necessary. Personally, I haven't placed any orders for materials yet, because I haven't seen enough proof that HOPE is as good as BushWacker says. Does this mean that I'm going to bash, criticize, and spread mistrust about him? No, of course not! Instead of doing this, I would recommend trying to help BushWacker out. This is the best way to see if HOPE will work or not. Isn't this forum supposed to be used to present and develope theories and ideas?
In the future, let our posts contain more constructive criticism, than accusations(implied or direct).
I hope this forum can continue to be a place to share information, and develope ideas for the HOPE generator.
Now that thats been said, onto more important matters...
I was reading over the final wiring configuration in steps 15 and 16 of the tutorial, and found it to be very confusing the first time through. I re-read it several times and drew up a little sketch of what I got out of the tutorial. BushWacker: Would you be able to verify if this is the correct wiring configuration for the 6 smaller spools? Also, do the gaps between the various screws affect the operation of the unit, or is this still something to be tested?
BushWacker: Hope the "Engineering Department" finds some good improvements and can create some good output circuitry. If they can, then you might be able to create a closed system. Now that would be a good video!
Have fun,
Jin
Thank You Jin! (:
Now there is wisdom! I agree wholeheartedly with your view on this all, and if we try to be more constructive rather than destructive we may just see some positive results. I'm not trying to sell anyone anything and only attempting to participate in a community where a great many others are trying to find answers to our energy problems. I could go on and on as you have probably noticed but, I will spare you this time, lol. It's just that I am very passionate about getting out of our current energy nightmare.
Jin, the art work you have done is beautiful although the wiring is somewhat off a little. The larger exterior coils on the output coils should connect directly to the smaller external coils. Please Remember that this was only the very first unit that I had built and that things will most likely change as we find better ways of doing things. For instance, one of our forum members recommended that we use double wound coils which according to Tesla will absorb much more radiant energy coming from the core. Also, the second unit that I built was made with different gauge wire on all of the coils and the external coils do not pick up nearly the amount of energy that the first unit did. I also wound the 1st stage primary coils with an extra 200 wraps which was insulated and seperate from the first 300 wraps. This may be the reason that the second unit was nearly twice as powerful as the first unit I built. It seems that different measures may have to be taken for each unit depending on the gauge wire used, core size, the material which makes up the core, etc.., etc.. . I believe that this is because a HOPE unit needs to be tuned to resonate a certain way to achieve the highest output potential. I think its kind of like when you tap on a glass with water in it. If you add or remove some of the water or mass the tone changes. With the HOPE this will also change the output potential and/or optimum operating frequency range. I am pasting the wiring configuration which represents the first/original unit. However, as I have said this will only be the case for this exact design using the exact materials and instructions given to reproduce the first/original unit. If a different gauge wire or different core is used things will not work the same. Jin you are very wise to wait a while before spending any of your money on this. I've tried to tell everyone that there is a great deal of work and research that needs to be done yet before we get everything figured out, but some people simply don't get it. I should not have given in to all of the people who were bugging me to hurry up and post the instructions for the original HOPE Generator because it is causing a lot of problems. My advice would be to wait until we are able to nail everything down and find out the optimum design for this kind of technology. I don't even know if I should post anymore information at all until this has been accomplished so that people don't confuse everything I say. Anyway, thanks again Jin. Blessed are the peacemakers.
Best Regards,
Jim
For anyone truely interested in trying to understand how and why the HOPE Generator can function and produce more energy than is put into the system please take a look at the links which I am pasting below. Even though it seems it would be quite obvious that there appear to be "Piezo Stacks" IE: stacks of piezo crystals visable in the photo's and video's of Steven Marks "Ring of Power" some have decided to ignore this component and assume they know how Marks device works. I can tell you without very little doubt that they are way off in their assumptions. I am reasonably convinced that "Harmonic Resonance" plays a large part in the initial functioning of Steven Marks device's. I believe that "Phase Conjugation" is also a factor, and that "Back EM Flux" produced by the collapsing of induced EM fields is an additional factor as well. Now if you consider more than what these guys seem to know about anything you may very well be able to understand the certain similarities of which I refered to in relation to Steven Marks "Ring of Power" device. If the gold/brass colored cylinders in the center portion/area of Marks's device are not in fact "Piezo Stacks" then I would appreciate someone telling me what they are? If the device functions in the mannor and by the means that Freedomfuel is leading people to believe then I will personally appoligize. However I assure you that I am not assuming all things and have actually had a great deal of hands on experience with such things rather than merely theorizing everything. I do not assume that I know all the answers to the universe, and anyone who does restricts them self to extremely limited knowledge. All I ask is that people do the math and research and the experiments before drawing rediculous conclusions. Opinions are fine and everyone should have the right to their own opinion. However whether it is based on reality or fantasy can make a big difference in finding the truth. Freedom Fuel does have one thing right and so I feel I should give him/her credit for that. There is a rotating EM field associated with Marks's device. There is also a vortex like effect present. I have never denied this but there is in fact much more to it all than is being presumed by some. I would like to see someone here besides myself produce working alternative energy devices. That is afterall why I agreed to join this forum in the first place. Please take a look at the few links which I am pasting below for anyone who wants to understand how harmonic resonance plays any part in electrical engineering and/or physics. Anyone who has read any considerable information about Tesla should know but as long as our educators continue to teach half truths and refuse to recognize the major flaws in Maxwellean theory there is going to be a lot of confusion even among some of the best engineers.
Best Regards All,
Jim
----------------------------
Concerning over-unity
and ZPE related ... GIF file, uses Tesla's theory of resonant frequencies
http://www.unexplainable.net/artman/publish/article_1756.shtml
Resonance
http://www.umanitoba.ca/faculties/arts/linguistics/russell/138/sec4/resonanc.htm
Higher order harmonic resonance of electrons with electromagnetic propagation
http://www.iop.org/EJ/abstract/0032-1028/13/11/004
Wave propagation perpendicular to the magnetic field
http://farside.ph.utexas.edu/teaching/plasma/lectures/node86.html
Fundamental and Harmonics
http://hyperphysics.phy-astr.gsu.edu/hbase/waves/funhar.html
http://hyperphysics.phy-astr.gsu.edu/hbase/oscdr2.html#c5
Studies of electron heating and multiply charged ion production in an electron cyclotron resonance plasma
http://www.iop.org/EJ/abstract/0032-1028/18/2/001
Understanding Harmonics
http://www.powerdesigners.com/InfoWeb/design_center/Design_Tips/Harmonics/Harmonics.shtm
Power Factor Correction and Harmonic Resonance: A Volatile Mix
http://www.ecmweb.com/powerquality/electric_power_factor_correction_3/
I do not wish to shoot someone down if they are sincerely mistaken but Bushwaker has made such fantastic claims for his device that one cannot help question his sincerity or grasp of reality. For instance he wrote on 4th October ?The current input to output ratios of the HOPE Generator are more than 600 to 1 at the moment.? On 27th June he wrote ?When a certain level of volume is reached the unit immediately jumps up to at least 1000VAC and 2 amps minimum?. To claim a 2 kW output is so far removed from any margin of error one could expect from a MEG type device that it naturally arouses skepticism.
The use of neon tubes to demonstrate the device?s capabilities also seems odd to me. There could be some anomaly at work here because everyone knows that neon tubes can be lit without wires. So far he has failed to provide convincing evidence that it can power incandescent bulbs despite being requested to do so. His excuse for not doing so was stated in these words written 7th November ?I have said on several occasions that I am NOT able to light standard incandescent bulbs yet due to the nature of the type of energy coming from this device?. Yet he contradicts himself on 7th October when he wrote ?I have also recently plugged a typical 120vAC to 12vDC converter into the HOPE and tuned the audio frequency to both a 60Hz square wave and a sine wave to see if I could run a small DC motor guess what? The HOPE has no problem lighting xenon bulbs as well?. No information was provided about the rating of the DC motor or xenon bulb. In fact both TH Moray and Ed Gray could light incandescent bulbs in their demonstrations of devices that outputted ?cold electricity?. Here is a quote from Gaston Burridge?s article about the TH Moray device at http://www.nuenergy.org/alt/fate1956.htm which confirms that it is possible to light incandescent bulbs with ?cold electricity?:
?This current will light ordinary incandescent light bulbs. The light which comes from these bulbs is called "pure white on the blue side, not on the yellow side as light given off when the same bulbs are lighted with commercial currents."
?Radiant energy will heat electric flat irons and other electrical heating devices. It is claimed heating capacities are reached much more quickly with radiant energy than with commercial currents, and are considerably hotter than when powered with ordinary electric energy?.
Another odd thing about BushWacker?s presentation of his device is the claim that the input is sound, not AC. I wish someone would explain to me how a sine wave signal from the output of a sound card is not AC. Does he mean that the device only works when audio frequencies of AC are used?
The Gen3 plans are equally misleading. No information is provided about the direction the coils should be wound in relation to each other. In one of his posts he stated that the direction of the windings was unimportant as the device worked equally well whichever way the coils were wound. This is something I find hard to believe.
The diagrams show the same topology as the MEG tested by Naudin except that there are four input coils instead of two. The top LH and bottom RH coils are connected in series with each other and the AC input. The top RH, bottom LH and output coils are connected in series with each other with the output being taken from the output coils. No explanation has been provided for this peculiar arrangement of the connections to the coils or for the addition of six small coils outside the perimetre of the device.
The so called ?audio? input is wired in a way that does not make sense. There are four wires from the audio output of the source. The signal wires of each channel are connected to the same locations as the AC input. However, the earth wires of the stereo audio source are connected to a phone jack and nothing is plugged into the jack during normal operation as far as I can see. This means that if the signals from the two stereo channels are equal in amplitude and in phase there would be no current supplied to the input of the HOPE device. It is this in particular that makes me think that the whole thing is a hoax.
Finally the plans do not offer a testing protocol so they cannot be considered a repeatable scientific experiment. All we have a various fantastic and contradictory statements about the device?s performance in BushWacker?s posts.
Hi Freedomfuel,
I understand your skeptisizm and what you percieve as condradictory statements that I have made however I believe that it is a matter of misunderstanding and perhaps poor communication on my part that has lead you to this deduction. I have tried many times to post to this forum but most of the time I have had a great deal of trouble doing this. I suggest that if you have questions or would like certain statements clarified that you write to me directly and ask me so that there is no further confusion. I can see your logic and rational in relation to many things but I assure you that I have not made 1 false claim or statement as far as I can see. I know this because I have tried to be as truthful and accurate in my reports as my time has allowed. I agree that there needs to be more thorough data however please understand that it has been only a matter of months since the initial discovery. I am in an extremely akward situation and have been disabled now for 11 years total. My physical restrictions and problems make it very difficult to operate at full capacity around the clock 24/7 and my financial resources are absolutely 0. The U.S., government has made certain that I would not be granted disability even though every doctor and every examination has proven otherwise. You may want to believe that I am a liar and that nothing I say is true however I believe that if you would ask me to clarify what you percieve as contradictory that I could clear up the misunderstandings and confusion. I simply do not have the time for petty arguments with everyone who wants to challenge my integrity and there are more important things to do with my time. As I see it I am better off using my time more constructively especially since I have limited time to spend when I am feeling well enough to do anything. I am in the condition that I am in because of trying to be a nice guy in the first place. It is obvious to me now that my naive belief that anyone would appreciate a nice guy was only the result of false teaching by my parents and society. Even so, I believe that the issues involved with the whole energy debacle are more important than mine or anyone else's personal views and/or opinions. That is why I have posted what information I have on this forum in hopes that someone might be able to use the information in their own research. I've got the HOPE technologies covered Freedomfuel so don't worry about whether I'm telling the truth or lying or whatever. As the saying goes "The proof is in the pudding". I've got the pudding on the stove now but you may want to wait for it to cool down a bit before judging whether you like it or not. As I see it the more people working in as many areas of research as possible the more likely we all are to see some eventual positive change in the way we all live. I also believe as you do that Mr. Marks device is authentic although I believe that I have a better understanding as to why it works and how. I've tried to point out some things which are not widely known or where certain connections have been overlooked but I cannot spend my entire time teaching class to those who have not done all of their homework. Your skeptisizm is good but try not to have to much of it. To much of anything can have a negative impact on a person. I probably can't place all the fault on you for the misunderstandings or misconceptions but I am not perfect either. I'm sure that if you ask me to clarify something that I will be able to do this. The current HOPE unit is in the hands of an extremely qualified EE and so I am hoping that we will be able to give verified documentation on more of the technical aspects that so many have been asking for. Please try to remember that Steven Marks device has been out there for nearly a decade while my discovery with the HOPE generator is only a few months old. I make no direct claims of free energy concerning the HOPE as far as I can recall however I may have stated that several engineers believe that it is showing OU. Also, 1000vAC at 2amps does not equal 2kW as you implied that I stated and it never will no matter who says that. Please read what I post more thoroughly and I believe you will find that you are missing a lot and then perhaps mixing it up in your own imagination.
Cheers,
BushWacker
Hi Guys,
I just received the patent certificate for the HOPE Patent/Utility Application so it is officially registered now. I can hardly believe that it only took 4 weeks for them to approve the patent and even better is that they let us keep the original language in the application. This gives us a huge playing field and will allow just about any changes in design including the materials themselves so there should not be any need to re-write or update the patent anytime in the near future. I've attached the original application and patent certificate in case anyone would like to read them.
Cheers All,
Jim
Hi All,
Congratulations on getting your patent approved BushWacker! Always glad to here that progress is being made.
I've been busy with work and video games ;D, so I haven't work on my 3D model of hope recently, but its still coming along. I put a base plate on it and started laying out some of the wiring configuration. I attached a render for anyone who wants to see how its coming. I'll post the .dwg when I'm done so other people can see it in 3D.
Have fun!
Jin
Thanks Jin,
Remember that if you have any questions at all just drop me a line and I will get back to you ASAP alright? For those of you who are getting ready to build your own HOPE unit I suggest that you stick with the approximate wire gauge sizes quoted in the instructions. I have been trying various different sizes/gauges of wire in combination together but so far the 29 AWG for the input and 27 AWG for the output coils is giving me the highest potential output values. Our engineer took on a machine shop job for BMW and has had to work a lot of overtime so he still has not been able to do the investigative work that he needs to do. He ordered a new RMS MM which apparently got rifled from the mail so now he is waiting for a second one. Both of us have been having a lot of problems with receiving our deliveries lately but hopefully this will stop now so we can move on to the next phase. He has received the HOPE unit that I sent him so if we can just get the kit for the new amp circuit and the tools our engineer needs it shouldn't take more than a day or two for him to verify the COP rating and ship it off for show and tell, lol. I know I could sure use some decent equipment myself and this winding everything by hand is a total bummer! Anyways guys, I'll try to keep plugging away and let you know what the word is on the actual COP rating when I know for sure. For those who still think I'm trying to pull some kind of a hoax for whatever reason or rip someone off somehow just remember that I'm not trying to sell anyone anything, and God only knows why someone would make this all up. Maybe some people are just insecure in themselves and need to try and bring other people down in hopes that it will make them seem bigger? Like I said, God only knows eh? For those of you who are preparing to build a HOPE device just remember that I want you to see the best results possible more than anybody so don't hesitate to keep in touch if you need anything at all.
Cheers Guys,
J.D.
I hope no one minds the intrusion, but I've been digging about on various forums for information on Overunity (having only in the past few weeks learnt of it and had my interest greatly peaked), and like some others seem to have encountered the frustration of how seemingly opaque the explainations of bedini's and bearden's systems are. Having read through some of the posts in this thread, my 'hope' is once again rekindled.
Being as I am, a rather uneducated computer science student of average intelligence, I was wondering if someone could explain the basic principle of the HOPE device to me. The science is all rather complicated, and to be honest I'm more interested in the practical rammifications. Having only my high school science knowledge to build upon, I hope I can develop an understanding of how exactly this all works.
Here is what I understand:
1. Audio input is fed into the device. (Uh, in electrical form I presume? How exactly is audio transmitted by cable? Is the voltage or amplitude used to convey tone?)
2. Something happens inside the device
3. Energy is generated in the coils and fed out the other end.
Uh, as you can see, I'm a bit... new to all this. I appologise if you are all rolling your eyes and thinking "oh lord, go away". But as I've always been told, one can only learn by asking questions. And so... well, here I am.
BushWacker,
Plz, tell me, what is the main idea of your HOPE? I think, that the main idea of all solid state generators(MEG, HOPE..) is the high voltage or a high current. Isn't it?
Sorry fo my poor English.
Best regards, from Russia.
Hi All,
I appologize for not responding to the last two inquiries that were posted but I have not been getting the usual notices when someone posts a new message on this topic. I've also had a lot of difficulty in posting replies and have spent about 6 hours all together trying to respond only to be cut off.
Anyway, I am honored to have stirred your interest in the HOPE Generator and I hope that none of you will feel intimidated to ask whatever questions you may have. There are all kinds of people who are involved with alternative energy R&D and only a handful are actually Electrical Engineers or physicists. I believe that this is due to the psycological influencing and flawed teaching that most EE's and Physicists are taught to try and ensure that certain limits/laws are not passed in order to keep the elite in power/control. Nikola Tesla was perhaps one of if not the first to come face to face with this dilema and it has continued to be the case for the last century. If then we know that the laws are flawed and the teaching corresponds to the laws then who is the expert?
I do not claim to be an expert myself, and I have found that most of the time those who do claim to be the expert on something rarely know much more than the average person. This is why I tell people not to let so-called experts intimidate them and not to dump their hopes and dreams simply because someone tells them that they can't do something.
As far as how the HOPE Generator operates I can only tell you as much as I know at this time since it is all very new and has not yet been thoroughly investigated by more qualified persons than I. The current model is presently in the hands of the most highly qualified electriical engineer that I have ever known and I am confident that he will be able to explain much more in detail than I have been able to do so far. He wrote me today to tell me that he finally has the tools he ordered and will be examining the unit in depth. He has made several remarks to me that he is certain of the efficiency claims that he believes we can prove shortly but due to the nature of this field of research it is dangerous to state any precise claims until we have very solid evidence to back them up.
The HOPE Generator in its current design closely resembles the MEG unit which Tom Bearden and several other of his team members claim to have invented. The difference between the MEG and the HOPE Generator is #1 The MEG requires AC input while the HOPE utilizes sound/audio signals as the input source rather than direct AC input. #2 The MEG unit requires permanent magnets to operate while the HOPE unit does NOT require magnets. #3 The MEG unit has only 2 primary input coils wheras the HOPE unit has 4 primary input coils which are necessary to properly tune the resonance within the core. #4 the MEG unit uses AC current to generate electromagnetic fluctuations in the coils and core which in turn generates an electrical current in the output coils to produce a higher voltage level and allegedly higher current/ampere level than is put in to start with. The HOPE unit on the other hand utilizes sound (or) variable resonant frequencies which are tuned to superimpose one another and collide creating a piezo-like response within the nanocrystaline particles in the amorphous ferromagnetic composite material of the core which in turn generates an electrical potential that is further driven by high frequency phase inversion caused by the initial reaction of the sound modulation. When a critical decible/volume level is reached for the input signal a cascade reaction begins to occur within the core and coils of the HOPE generator and after this critical saturation point is reached each slight increase in volume/decibles causes the output voltage and current to rise exponentially to thousands of volts. The operation of the HOPE Generator is clearly more complex than that of the MEG, and I believe that the difference in design as well as the source input justify calling it a whole different animal than the MEG.
If you understand things so far you should be able to see now why I am excited about developing completely new materials to use in the further development of HOPE technologies. Add Barium Titanate, Lead zirconate titanate, Lead niobate, or even Quartz in combination with high frequency ferrite and ferromagnetic materials and I think you would see something that would make the current model look like nothing more than a toy.
The various reactions occuring within the HOPE Generator feed one another to compliment the other making it possible to require very little power to generate the initial audio frequency input. The output potential is visibly higher to anyone who has seen the HOPE function and to date everyone who has seen it in person insists that it has to be producing OU. Even so, I have not made any claims that this is the case because I am perhaps the biggest skeptic around, lol. I will not make claims of breaking the OU barrier until absolutely no battery or outside audio source is needed and there is no way to deny the fact.
Personally I believe that the obvious efficiency level that I have seen to date is enough to justify further R&D into this kind of technology. Also, as I have said it is all still very new, and I am convinced that much better materials can be developed to create much greater output potentials than we are seeing now. Because of the complexity and various unknown phenomena which may also be contributing to the function of the HOPE it may be best if we all let the professionals take some time with it before we all get to exited. I have to admit that I am excited and impressed by what I've seen so far but its always better to wait for the final word on things like this before going nuts and telling everyone. It wouldn't be the first time that it appeared that the OU barrier had definately been broken only to find some weird anomaly that nobody recognized at the start.
I hope that answers your questions guys. Our engineer is going to be working on this all in the next couple of weeks so I'm hoping to be able tell you more then. I'll also ask Bill (our engineer) if he wouldn't mind explaining things to some of the more technically minded individuals who don't understand laymans lingo, lol. Bill is sort of a cross between a modern day Albert Einstein and Nikola Tesla. I've never met his equivilant or for that matter ever heard of anyone who could match mind's with his. Bill has also been involved in black projects for various contractors and has had his own experiences with MIB. I've got a good 10 years on Bill in the field of alternative energy tech but you certainly wouldn't know he's only been into it for 20 years. Sometimes it may take years before you will find an authentic OU technology but when you do you don't forget it and it changes your whole way of thinking. Then if and when you actually try to develop something you need to be prepared to deal with these kinds of people. Enough said I guess.
Best Regards All,
Jim
One additional note about the HOPE that I forgot to mention is something which is theoretically feasible is that there may be an additional factor involved with the operation of the HOPE unit. Please remember that this is on a theory and is not to be taken as absolute fact at this stage of investigation. Several people have suggested that the difference in relaxation times between the various metals which make up the core and coils of the HOPE could possibly be contributing to the efficiency and operation. If this turns out to be the case then it would mean that there may be an additional way in which this technology can be improved besides the addition of piezo reactive elements and various improved core materials. Indium has been suggested by a friend of mine as one possible test material to try for the induction coils. Its pretty clear that there is going to have to be some intensive research involved to find out what the ultimate combination of materials will be. The shape and overall design of future developments may be quite different from the original discovery and in my opinion it would seem highly unlikely that I accidently hit upon the best overall design on my first attempt. I think that the biggest point to note should be that sound frequencies can be utilized to invoke current in materials other than the typical quartz crystals that we're all familiar with. This is what sparked my curiosity to begin with and its what lead me to investigate things further. Theres still a lot of room out there for discovery people so don't let the man bring you down, and don't give up your common sense through intimidation from so-called experts with monstrous ego's. Knowledge is a good thing but to many books can impare your vision from seeing what may be right in front of your face.
Cheers,
JD
Hi All,
I spoke with our engineer this evening and he told me that he has
had a chance to check some initial readings on the HOPE unit that I
sent him. He has confirmed the nice smooth sine wave output signal
and is getting an initial reading of approx., 600+ vAC on an RMS MM
without a load being applied. I think he will be very suprised to see
that the unit actually runs even more stable when a load is applied.
He has lowered the initial input voltage to a maximum of 5vDC and is
optimistic that we should be able to close the loop on the system. If
not, I assured him of the fact that we could simply plug in another
unit to the original signal and automatically double our output
without any noticable loss of power to the initial unit. I've already
done this in several experiments at home so I already know that this
is the case. I don't know exactly how many units can be run off the
original signal before any appreciable loss of power to the
preceeding units but since I know that at least 2 units can be hooked
up in sequence we should then already have enough additional power to
pick up any losses by feeding what little extra power is needed back
to the oscillator/amp circuit to make up the difference if need be.I
guess I shouldn't say too much more until we have actually closed the
loop. For now I figure it ain't over till it's over. It is
good to finally have a real expert have a look at things rather than
expect everyone to wonder whether or not I'm just reading something
wrong. We're hoping to have things pretty much ready for show and
tell in the next week or two unless something else comes up so we may
have more acurate data to post for you all here pretty soon. Sorry
about the delay on the beam projector guys but I can only do so much
the way things are at the moment. If things work out like we're
HOPEing, the beam projector will be one of the first things
on my list to finish. I have a very special interest in the ISBP
technology myself but my current tools and environment are not
conducive to finishing this project at this time.
Best Regards All,
Jim
I have had time to think about Bushwackers HOPE generator and I am certain that there is something going on in this device worth investigating.? This conclusion was reinforced by some comments made by Steven Greer in a recent radio interview that suggested that other researchers may be trying a similar approach.
The conclusion reached so far is that there is something happening inside the amorphous metal core of the HOPE transducer that is producing an overunity phenomenon.? Bushwacker and others such as Greer think that it has to do with resonance, but I think that there is more to it than that.? I believe that if ?free energy? exists then it must have existed in nature for eons and mankind has till now failed to recognize it.? In this example I suggest that what is going on in the core of this transformer is the same phenomenon that causes earthquake lights.? These are luminous phenomenon that appear over fault zones and are believed to be cause by the crushing of rocks during seismic activity.? The lights may be in the form of a dome of light over the fault or else they may be balls of light hundreds of feet above the ground and these fireballs may appear to rise out of the ground.? These luminous phenomena may last for minutes or hours.? All the hypothesis put forward to explain this phenomena are based on the idea that a separation of charges occurs in the rock?s crystals as atomic bonds are broken.? It may be the same effect as piezo electricity or more likely it could be triboluminescence .? This is supposed to account for the flashes of light as crystals are crushed, scratched or rubbed.? It is believed that when asymmetrical bonds are broken in a crystal there is a separation of charges leading to an electric discharge and a flash of light as the surrounding air is ionised.? A recent controversial theory based on laboratory experiments is that there is a separation of positive hole charge carriers that turns rocks momentarily into p-type semiconductors? and that this occurs in a horizontal layer of rock which rapidly moves to the surface to produce a coronal discharge. You can read about the various theories to explain earthquake lights at Wikipedia here:
http://en.wikipedia.org/wiki/Earthquake_lights
Also try this article: Earthquake Lights In New Scientist
http://www.weatherzone.com.au/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=16;t=001380
There is also a documentary on the subject regularly repeated on the Discovery channel called ?UFOs; Great Balls Of Fire?.
What none of these theories can explain is the longetivity of the luminous phenomenon associated with fault zones.? It is the longetivity of the lights that suggests that they are being sustained by taking energy out of the environment, which would make them a natural form of free energy. In my opinion such phenomena as earthquake lights, ball lightning, and the NASA UFOs are magnetic phenomenon that depend on the earth?s magnetic field.? These balls of light could be spinning magnetic fields in the form of torii and they could be sustained by sucking magnetic energy from the ionosphere through a magnetic vortex just as free energy devices do.? Recent research suggests that there is a link between sunspots and earthquake activity.? Sunspots are secondary magnetic poles on the sun with powerful magnetic fields in the 500 gauss range, which could be ejecting fragments of the sun?s magnetic field as packets of magnetic energy in the form of spinning torii.? These would be absorbed by the earths magnetic field in the ionosphere and cause not yet understood changes in the geomagnetic field that trigger earthquakes.? See this article:
Sunspots and Eartquakes
http://www.rense.com/general69/sunspots.htm
To develop this hypothesis further we need to know more about the amorphous metal material used in the HOPE device.? As I understand it this material does not seem all that different from the ferrite cores widely used in electronics.? These are, I believe, alloys of Iron with Cobalt for instance which are finely divided and solidified under heat and pressure.? Is this the same kind of material as is used in ceramic magnets? Barium ferrite maybe?? The fact that the magnets in Bearden?s MEG device tended to disintergrate suggests that the amorphous metal core material is also being stressed when subjected to an alternating magnetic field.? This could lead to the kind of phenomena associated with earthquake lights sketched above.? This hypothesis could be supported if Bushwacker had ever observed a glow of light around his device in darkness as it is operating.? Also there could be acoustic waves present in the core and this could be discernable as a sound emanating from it.
For the device to be overunity there would have to be vortex magnetic fields associated with it somehow.? It may be possible that electric discharges inside the core material take the form of ?charge clusters? as taught by Ken Shoulders. These are thought to be spinning torroidal clusters of electrons that form in ordinary electric sparks and which also have a vortex magnetic field associated with them.? It is this vortex magnetic field that connects with the ionosphere and extracts energy from the earth?s magnetic field.? Such charge clusters are believed to be formed in the cathode of cold fusion cells and they are regarded by some as miniature ball lightning.?
According to the above analysis there should be no need to follow the topology of the MEG device to investigate the overunity potential of amorphous metal and other materials.? I suggest that a simple bar or ring of the material to be investigated could have a single coil primary attached to it with a single coil secondary and the later would have to be bifilar wound to eliminate inductive coupling between the primary and secondary and ensure that the output is only magnetic current.? A number of different composite and ceramic materials could be tested and these would not necessarily have to be ferromagnetic.? Even plastics could be tried.? Measurements of magnetic current using digital voltmeters are meaningless as proof of overunity so I suggest that the difference between the input and output could be proven by taking the output to a calorimeter.
Here are some links for charge clusters:
A Demonstration Of ?Charge Cluster? Phenomenon
http://www.amasci.com/weird/evexp.html
Observations On the Role Of Charge Clusters in Nuclear Cluster Reactions
www.svn.net/krscfs/nev%20clusters%202.pdf
The Ball Lightning State In Cold Fusion
www.iscmns.org/iccf11/ppt/LewisBallLightning.ppt
Charge Clusters In Action
http://svn.net/krscfs/Charge%20Clusters%20In%Action.pdf
High Density Charge Clusters and Energy Conversion Results
http://padrak.com/ine/FB97_1.html
Electron Clusters ? Possible Deuterium Fusion Catalysers
http://www.lenr-canr.org/acrobat/ChiceaDelectroncl.pdf
Lars Johansson.? Longitudinal Electrodynamic Forces
http://www.df.lth.se/~snorkelf/LongitudinalMSc.pdf
C.P. Kouropoulos.? Classicaly Bound Electrons - EV?s, Exotic Chemistry, and ?Cold Electricity?
http://www.mypage.bluewin.ch/Bizarre/EVs.htm
R.A. Nelson.? Ken Shoulders? Electrum Validum
http://www.rexresearch.com/ev/ev.htm
? ?
After my initial scepticism I have started to become quite excited by the possibilities being demonstrated by the HOPE device but I think that we should be cautious about any averunity claims untill a test of the output with a calorimeter is done. This is the gold standard test of overunity which no one can argue with. Fortunately it is easy to make your own calorimeter. It could be that the HOPE device is merely an exotic form of electrical transformer and not overunity at all. Here, for instance, is a description of a transformer using the piezo electric effect:
'A piezoelectric transformer is a type of AC voltage multiplier. Unlike a conventional transformer, which uses magnetic coupling between input and output, the piezoelectric transformer uses acoustic coupling. An input voltage is applied across a short length of a bar of piezoceramic material such as PZT, creating an alternating stress in the bar by the inverse piezoelectric effect and causing the whole bar to vibrate. The vibration frequency is chosen to be the resonant frequency of the block, typically in the 100 kilohertz to 1 megahertz range. A higher output voltage is then generated across another section of the bar by the piezoelectric effect. Step-up ratios of more than 1000:1 have been demonstrated. An extra feature of this transformer is that, by operating it above its resonant frequency, it can be made to appear as an inductive load, which is useful in circuits that require a controlled soft start. A detailed analysis can be found here. These devices can be used in DC-AC inverters to drive CCFLs.'
This quotation has been taken from the following article:
http://en.wikipedia.org/wiki/Piezoelectric
Hi FreedomFuel,
I'm glad to see that you've found evidence to show that this is possible and I also agree with you that we can't make any claims of OU until all test results are in. I've got my best HOPE unit in the hands of the one person that I know who has the knowledge and experience in electrical engineering to do these tests. The calorimeter test is one of the tests that he told me he planned on doing. I've been waiting three months now for this guy to get busy with the unit that I sent him but I don't think he has done a heck of a lot of anything so far and I'm beginning to wonder if this guy was the right choice to choose as a business partner. The current model is basically the first working example of an initial theory that I put to the test and I believe that the design will most likely change as more information is gained over time. The example of the piezo-ceramic rod/bar that you pointed out is helpful to me and I believe that as time goes on we may be able to find much better materials and designs which will make the current model look silly by comparison. Hopefully others will gain interest from the evidence that we are finding and sharing here to invest some time and research into all of this. My gut feeling is that we need to look at combining piezo reactive materials such as Barium Titanate, Lead Zirconate Titanate, Lead Niobate, and perhaps even simple crushed quarts with high grade ferromagnetic materials to see if we can improve the materials that we currently have to work with. I suspect that if we can use various frequencies to induce a much stronger initial electrical reaction in a material, use that reaction to create an electromagnetic reaction, and add the copper coils to magnify that initial electromagnetic reaction with proper harmonics we may really be able to induce such a device to true OU. My intentions are not to try and sell people HOPE units but to try and point out the possible chance that most have been overlooking this type of approach to alternative energy technologies. We've got a long way to go yet but I think we've accomplished a good deal so far just by pointing out what we do know to date. Thanks again for that info FreedomFuel. I will send the link to our EE.
Cheers,
Jim
Original HOPE Generator Instructions
Now available in .PDF format.
Click on attached file to download.
Cheers All,
J.D.
Hi,
This may have been covered, but what are the differences between the HOPE gen and Bearden's MEG?
Thanks,
~D
I'm e newbie in this forum and this is my first post and it will most probably be the only.
I've been reading on this topic for the whole evening from soon this afternoon.
Here are my observations:
1: you say that you do not feed your system with AC but with sounds.
What are sounds if not AC.
AC means alternating current.
An audio signal is an alternating current. Thus, you feed your system with AC.
A signal generator is a device able to provide alternating singnals of variable frequencies.
2: You said that your system has lots of energy but what is energy?
Energy in electricity is measured in terms of power and power is the results of voltage multiplied by the current.
However nowhere you gave an idea of the power delivered by your system other than 1000v at 2 amps which is 2kw.
I'm rather surprised by this when all you've been able to make your system is to turn on a few small fluorescent tubes.
Is is very easy to light uu fluorescents and being a ham radio since 35 years I know what I'm talking about because when I was younger I used to facinate my neighbors by lighting a fluorescent in my backyard with no wire connected to it. The trick was that before to go out, I used to put my transmitter on the air with 100 watts in the antenna and I knew that all I would have to do would be to come under my antenna and lift the fluorescent in the air above my head while I was under the antenna and that's it the fluorescent would glow.
Anyway, a fluorescent the size that you have doesn't use very much power and in the worst case, 20 watts or so would be sufficient to make it glow.
I would have been realy impressed if you would have connected a high power appliance and make it work to its full potential but that was not the case.
I'm not trying to say that you're a liar or anything alike.
However, to me you're just a poor guy who has not the slightest idea what he's doing and playing with.
By reading your information, I found that the ratio of your transformer is varying between 6 to 15 according to the number of turns of the numerous primary coils wich are ranging from 200 turns to 500 turns while your secondary coils are of 3000 turns.
Thus it is realy easy to go to 1000v with such a ratio because in the worst case, all you have to do is to provide a 100v signal to the 300 turns input coil and that's it that's all you will get 1000v at the output.
But it is not because you have 1000v that you have energy!
With a few miliamps all you can do with 1000v is to kill some moskitos hehehe :)
Besides, I remember that you mentionned that you could get 1000v at 2 amps at the output but you also said tou you couldn't even light a bulb with such a power.
C'mon man, try at least to agree with you own sayings. 2kw of power could easily turn on 20 bulbs of 100watts at their full capacity.
On the other hand, I'm extremely doubfull that your secondary coils could sustain 2amps with the size of the wires that you've used which is number 27 or 29 If I'm I remember.
Fisrt of all, there are no wire of such size like #27 or #29. The nearest is #28.
It could have been possible to sustain 2amps with secondary coils wound with #16 or #18 wires but I don't think so with so small wires such has #28...
The fact that appears more and more as an evidence to me is that your system delivers very very small power and it explains very well why it doesn't generate heat. There's no heat because there's no work accomplished by the load, that's it, that's all. By work I mean power. Power can be in the form of watts or in the form of HP. If your system would drive a 20amp motor at 100V then it would deliver 2kw of power when this motor would accomplish a mechanical work that would use all this power not when the motor would spin freely unless it would be a very very big motor needing such a power only to spin at the idle (without doing any work).
I'm sorry If I nmissed a post where you would have said that you powered a 2K electrical applicance for hours because if it would have been the case then your system would have generated heat and a lot of heat as a matter of fact becuase if it would have generated 2Kw of work it would have also generated 2Kw of heat and as a result your tansformers would have been gone in smoke because the size of the wires of your secondary (output coils) are just too small to support such a power.
The conservative rating of #28 wire is about a quart of an amp thus I realy doubt that it could sustain 2 amps at 1kv
The only thing that is clear to me is that your system is realy far from being a MEG.
Regards.
LancaIV,
I did research in DPinfo and found the patent DE3900890 has been cancelled. See attachment.
Do you by chance have a copy of this Heyer-Patent ? Is he willing to cooperate and reveal his technique ?
Thank you in advance
Kator
Ol? Lanca and Hello Kator,
I found Heyer's DE3900890 patent at the Europen Patent Office, see link here:
http://v3.espacenet.com/textdoc?DB=EPODOC&IDX=DE3900890&F=8
I must translate somehow it to English though, I am not good in German language... :o
Yes, the patent includes lots of numerical data which is good in itself but must be digested to make it clear.
I like his MEG-like arrangement, especially his Fig.5 with Fig.6 drawings, very interesting, I have not seen such ellipse-like holes/cut-outs in rotors of expected overunity machines! This shape may make the surface area change non-linearly and this is most welcome where sudden flux change is expected.
Regards
Gyula
Hello LancaIV,
unfortunately - thought I have DSL - I cannot access DEPAtisnet and also the Dpinfo is dead.
I have to try it later.
Question : Is Horst von Heyer living in Kasendorf ( Franken ) ?
Thank you for your info. I am pretty busy with different developments and this limits my time here.
Lates flop with Daniel Jackson made it clear that there is a lot of desinfo spreading here which forces me to distinguish
more accurate.
Regards
Hallo LancaIV,
do you have the impression after you talked to Mr. Heyer, that he has ever build this machine ?
Or is it just a concept never realized ?
Sincerely
Kator
These Ruthless people supressing this stuff have lost most of there sences, and are fuel by jealousy(tornmented by satan) because of the qualitys they lack due to deprivation and fear/afraid,
and useing microwave weapons - ruthless , they are fueled by jealousy and when they say useless eaters, well actually they speak of there own, since they Waste alot and absorb all this money which they don't need and Waste.
so then they get these guys to be sodomized to become one of them and be jealous of people with the common decency, which they once had, and remembers the silence they enjoyed.
whats the Point with haveing all of these Material Possession and pleasures of the flesh that isnt everlasting?
when you could Have Joy which lasts?
with enough to spare over?
not this under unity - broken dream - illogic science .
it Just comes to show you , just how much respect these guys have for them selfs because they hurt them selfs and hurt others as well as much as them selfs.
well at least one of theres has left them , call saliva who was actually Sane enough to see through the lies.
And Had Enough Decency Left in HER To Tell the Truth and the Guts.
because the lies / if kepts on , would of depraved what was left of her.
and these Illogic Wasters need to Go,This is God's Planet and they are RUINING IT, and not MANS Planet.
well what do you Think , is today Honourible ?
No..
lltfdaniel1,
Get a life and leave us alone.
You picked the wrong forum with your crap mate!
Try this forum: http://www.mad.gr/forum/ubbthreads.php
I am sure they love you there!
In reply to cverr I would like to point out that the excess energy from so called 'free energy' devices like the HOPE generator is not electricity.? Rather, this new form of energy could more acurately be described as 'magnetic current' and theories derived from conventional electrical engineering teachings do not apply.? I have seen ample evidence that this magnetic current is neither a wave or a stream of paricles but rather flowing vortex of magnetism around the outside of conductors. Since the factors that cause heating in electrical conductors do not apply with magnetic current there is not the same heating effect when the same amount of power is being conducted for a given diametre of wire.? In practice there is no consistant relationship between the power output of a free energy device and readings made with a digital instrument so claims made by Bushwacker based on such readings should not be taken seriously.There is a consistant relationship between the power supplied in the form of magnetic current and the readings of moving coil instrumets but the actual readings are meaningless since 'potential' and 'current' have different meanings with this form of energy.
All this might sound weird to someone with a degree in electrical engineering so I can understand why they might be sceptical.? You have to accept that this is a whole new physics that has been concealed within military research establishments for at least 60 years, but one day it will be taught in our schools.? Here is a guide to the new magnetic technology you may like to study:? http://www.magneticenergy.org.uk
I have to concede that so far Bushwacker has not given convincing evidence that much more energy is available at the output of his device compared to the input.? However, in my previous post have shown how such a device could indeed be overunity in theory so I am prepared to keep an open mind about any overunity claims untill definitive measurements can be made with a calorimeter.
Hi LancaIV
Tell me more about the visit of rexresearch and Professor Ehrenhaft.
I have done some more research on the internet and I have concluded that such 'overunity transformers' must all depend on the phenomenon of 'triboluminescence'. ?Here is a paper written by one of the few scientists studying this phenomenon:
Wintergreen Candy and Other Triboluminescent Materials
http://pages.towson.edu/ladon/wg/candywww.htm#Spectra
This paper supplies graphs that show that the emission spectra of crushed sugar crystals is the same as that of lightning thus proving that there is an electric discharge involved and the light emitted is from the excitation of Nitrogen in the air. ?The paper also states that one third of triboluminescent materials also exhibit piezo electricity and the majority of piezo electric materials are also triboluminescent. ?I have not been able to find any information about how triboluminescence could be induced in piezo electric materials but I suppose that such materials could be excited ?either electrically or mechanically. ?There is enormouse potential for research here if some way could be found of collecting and measuring the magnetic energy being emitted from charge clusters in the material. I suggest concentric perforated tubes to capture the expanding magnetic bubbles from each discharge.
Another possibility I have considered is that triboluminescence may be overlooked in some experiments if it does not produce visible light. ?I hypothesise that charge clusters are produced in the brittle metal hydride film of 'cold fusion' cells by the same mechanism that produces triboluminescence in crystaline substances. ?With cold fusion flashes of light are not usually visible yet there is photo microscopic evidence for electrical discharges in the cathode. ?See the work of Ken Shoulders. ?I also believe that it is possible that sonoluminescence may also be due to an electric discharge ?in collapsing air bubbles and that any overunity potential of such devices may not be due to fusion of deuterium nucleii by heat as it is commonly understood. ?
Another interesting possibility is triboluminescence in plastics. ?You can demonstrate this by unrolling sellotape in the dark. ?Here is a weird experiment by Hal Puthoff that could depend on this property of plastics:
A Cursery Examination Of the Glow Discharge Panel
http://www.earthtech.org/experiments/gdp/cursory.html
You can see the original experiment done by JL Naudin here:
http://jlnlabs.online.fr/plasma/html/s_gdp1.htm
I believe that there is some kind of electric discharge going on here because Naudin says that Nitrogen Oxides and Ozone are produced by the device. ?I also believe that the glow around the device is not a plasma as it is normally understood but rather the same 'magnetic light' that occurs with the Adams motor. ?This device, in my opinion has potential for overunity if it is developed further.
Quote from: lancaIV on January 22, 2006, 06:13:26 PM
please visit the rexresearch-archiv(go to the post before) for the Prof. Ehrenhaft-Information,I think that the most
important statement you will find is inside "(5)Magnetic Currents-.....Ampere Refuted" !
Sincerely
? ? ? ? ? ? de Lanca
I think that the idea of magnetic charges is intriguing and I know that Myron Evans, an associate of Tom Bearden, agrees with Prof Ehrenhaft that light contains a stationary magnetic field. I am using magnetic current to describe something that is more like a fluid than a flow of particles, but I am open to the idea that there are magnetisms in the atmosphere that do consist of particles.
The Ehrenhaft material is certainly very interesting since magnetic monopoles are a hot research topic today. I wonder if anyone has attempted to reproduce his experiments recently.
Begin Forward:
For those of you who have been keeping tuned to the progress of HOPE R&D you may want to just skip the forwarding message immediately below and go directly to the information update.
J.D.
-----------------------------------------------------
Because of the large number of requests for more in depth information concerning developments in HOPE technologies I must reply to your request in the form of this general response due to the lack of sufficient time to answer all the individual requests for information at this time. Unfortunately there are no other persons involved in the R&D of HOPE technologies to date, and t o my knowledge I am currently the only person investigating this discovery so far. There is a great deal of R&D that needs to done in this area before anyone can claim to be an expert and so I ask that you please keep this in mind. Even though I have been able to learn much during the months since this discovery there are likely many things which will change during the process of investigating the various phenomena and physical principals involved with the HOPE approach to alternative energy. The information which I will be relaying to you is intended to help you to better understand some of the principals involved with the production and transfer of energy during the operation of HOPE but does not rule out possible means of improving upon current designs and/or configurations of HOPE Generators. I encourage all free thinking individuals to utilize their own personal knowledge and intuitions involving this type of approach to AE technologies and to try to look beyond the typi cal applications of many existing technologies which you may already be aware of. Because there is still a great deal of investigation and work that needs to be done in order to better understand the full potential of HOPE style technologies this field is now open to all who desire to join me in the R&D of HOPE. I have been able to prove that it is indeed possible to invoke high electrical potentials by means of harmonic resonance and phase conjugation/inversion within certain materials by using the proper materials and electrical configurations. I have now successfully acquired the international patent certificate for all current and future developments of HOPE technologies. I have taken the steps necessary to acquire this international patent NOT for the purpose of restricting further developments but, to try to insure that certain entities are not able to lock this knowledge away as they have succeeded in doing with so many other alternative energy technologies to date . I am pleased to share any successful improvements and/or developments with those who share the vision of true freedom and progress, however I will give NO allegiance or means to control this technology to any individual, government, military, or corporate entity. I have had a good deal of personal experience with the powers that be who do not want the general public to know that these technologies in fact exist. My reasons for pursuing these kinds of technologies are not strictly for personal gain, and I hold no illusions of becoming extremely wealthy by presenting them to the market-place. On the contrary, I believe that in order for mankind to be able to evolve to the level that we have the potential to experience we must first overcome the obstacles that have been intentionally placed in our way by those who wish to continue to maintain power and control over us. The time of innocence and ignorance is over, and it is now up to each of us to see that future generations do no t fall prey to the same controlling class that has held mankind hostage for far to long already. The information that I am sharing with you is intended to be freely distributed and may be shared with anyone and everyone you wish. Please remember that HOPE technology is only in its newborn stage and is completely open to be researched and developed by any and all who wish to pursue it. There are many other technologies that I believe the people have a right to have available to them as well, and which I am also currently trying to find help with however as time will not allow me to share everything at this point I must therefore restrict the following information to that which is involved with HOPE Technologies.
Latest Info on HOPE R&D:
Since the basic step-by-step assembly instructi ons for the original HOPE Generator explains the purpose and function of HOPE Technologies for the most part I do not want to be wasting valuable time to go into these general details once again. Therefore I will try to avoid repeating that which has already been explained and try to restrict the following information to what I have been able to learn since writing those initial assembly instructions.
In my recent months of investigation I had hoped to find out far more than I actually have concerning the many technical details of operation. The so-called partner whom I had recommended and asked to be the Electrical Engineering expert for the new company that we have been trying to form IE: Genesis Engineering Unlimited (GEU) has now had my best HOPE unit in his posession for the last four months. However he has proven to be of little use in determining the details of which I had hoped to learn and pas s on to others. Therefore, I am giving him two more weeks to do something before I request that the unit be sent back to me. I have spent a great deal of time and money towards this purpose to try and enable him to aquire the proper tools in order that he would be able to investigate the technical aspects of operation. It appears that 4 months time is insufficient to build the small amplifier circuit that we had decided on building to try and boost the output to much higher levels. Most folks consider me an extremely patient man however I suppose that 4 full months of doing absolutely nothing should be enough time to show anyone what they can and should expect or in this case I guess, not expect. Even so, I have personally continued to work very hard to conduct my own research into HOPE tech as best I can, and have learned some additional information of which I believe may be of some interest and value to someone out there.
What I have found is that there seems to be a definate relationship between the specific material makeup of the core, an apparent piezo like component present in the core material itself, the electromagnetic components of both the core and copper coils, and the total mass of the total unit assembly which will depend upon the particular core to be used to build any particular HOPE unit. As far as I can see up to this point, the size of the core does not seem to be as much of a factor responsible for producing the potential output as I had previously presumed. However, being that I am still currently in the process of testing the various sized cores and configurations I am not yet ready to draw any definate conclusions on this just yet. One advantage that a larger core does provide is that it does allow more space for coil configurations and more total area to provide for induction by those c oils.
On the unit that I had built and sent to our alleged engineer, I had added an additional but seperate 200 winds/wraps of 29 AWG wire on top of the initial 300 winds/wraps on both of the 2 first stage induction coils. The second set/stage of induction coils were each wrapped with the usual 500 turns of 29 AWG wire. The extra 200 turns of wire on each of the two first stage induction coils was then insulated from the initial 300 winds/wraps, and the leads of these extra winds/wraps were routed back to the initial input. This successfully boosted the output potential substantially and raised the output level several hundreds of volts higher than it had been previously to adding these additional coils to the initial 300 winds/wraps. When I had tried to simply add an additional 200 turns directly to the initial 300 winds of the first stage input coils s o that was instead a continuous 500 turns there seemed to be no difference in the output potential. Therefore since it seems likely that it was not a direct increase in the electromagnetic component alone which contributed to this rise in potential. It seems logical to me that it was the way in which I had configured the additional 200 winds seperately from the initial 300 winds which seems to have caused a phase inversion within the core resulting in this greater induction and output potential. I could be wrong but by taking all things of which I have observed thus far into consideration I can think of no other reason for this kind of reaction to occur. I have just completed a very similar set-up with a much larger AMC-1000 Powerlite C-core but due to the level of e-mail that I have been receiving lately I have not yet had the opportunity to conduct any experiments with this unit. I should be able to do this within the next couple of days and will publish any successful findings w hen I have the time.
Last evening I was almost ready to throw in the towel on a new wiring configuration and so I decided to try and get some rest. As usual thats often the time when my mind likes to go into high gear, and after being unsuccessful at falling to sleep after about four hours I finally gave up and went back to work to try the configuration that had kept surfacing in my mind. It seems to be working well and now appears that I have found an even better wiring configuration than the one I used for the unit that I sent to our engineer. The new configuration should allow for additional coil space on the 320 core although I haven't yet had the time to try that either. I have tried so many different wiring configurations throughout the last 3 to 4 months that I have lost count. Some work better than others and some will only work in conjunction wit h a specific transformer. Another important note to remember is that certain transformers seem to compliment a HOPE unit by not only greatly widening the range of prime operating frequencies but it can apparently boost the total output potential by a large margin as well. I'm not certain how or why this is, only that I have seen both the voltage and amperage levels rise significantly when the proper wiring configuration is found for a particular combination transformer and HOPE unit.
Another important finding is the fairly recent application of a miniature audio transformer. This little component is inexpensive and can be found at Radio Shack. Somehow by bridging the the Radio Shack mini amplifier unit with this little audio transformer it allows the 320 HOPE unit to operate strictly on feedback from the audio amp circuit when it is hooked up properly. When this is done the voltage goes off the scale on my MM and the very noticable increase in ampere's cannot easily be explained away. So far every measurement that has been taken on the unit which our engineer now posesses has registered just under 3 amps max., at approx., 683 vAC. I believe that the new configuration which I had discovered only this morning is noticably higher still, however I do not have the proper tools to correctly measure the AC amps. I know that there are probably many who would disagree with me on this but, to me this is no big thing and no matter how I go about trying to provide evidence there is always someone who will inevitably try to blow it off as heresay anyway and call me a liar. The skeptics are never satisfied until they can see it and touch it themselves, and I am always happy and willing to see their reaction when they finally do, lol. I would love to see someone show up at my door and ask to examine a unit. Engineering standards do imply that you can boost a few volts up to a few hundred volts however according to these rules as that voltage increases the amperage must decrease and vice-versa. In this case that standard does not seem to hold water anymore, and as I have previously stated, such an apparent increase in both the voltage and the amperage cannot be easily explained away by using these standard rules. The only thing that makes sense in this case would be in my opinion the presence of an initial piezo-like reaction that is influencing an electromagnetic response within the core and coils and thereby an increase in current response which actually seems to cycle the unit up to a much greater operating potential. This observation is how I came upon the idea of intentionally using highly reactive piezo materials such as "Lead Zirconate Titanate", and/or "Barrium Titanate" together with a highly permeable ferromagnetic materials etc.., etc.. . Other candidates to consider for possible materials which may likely incr ease the output potentials of future HOPE style generators might also require those which conduct better sound resonance such as "Indium" or possibly even glass made from pure crushed quarts. We have entire beaches made up of this material and it is at least nice to think that the cost to make such custom core materials could actually drop rather than rise. Who knows at this stage in the game right?
By far, two of the most interesting pieces of information that I have learned recently involve (1) what seems to be this piezo-like response to the initial audio stimulus within the Powerlite core materials that I have been using. I believe that this is likely due to the nano-crystaline particle structures present within the materials used to make the Powerlite cores. These cores are comprised of high grade ferro-magnetic metals and basically speaking glass. Thus the name of the manufacturer that makes them eg; (MetGlass). The material is produced in the form of a thin tape which is then layered and formed and then bonded together to form a solid core. (2) Secondly, it appears that the total size and mass of a particular core along with the specific gauge of wire and corresponding number of wraps will largely determine the prime frequency range that will be required to produce the optimum electrical potential. This may seem somewhat obvious to many of you since we know that the specific materials, size, shape, and mass are all very important in designing many musical instruments. However, there seems to be something else happening here in addition to what may at first appear plainly obvious. There is a lot of phasing or phase inversion that is going on within a HOPE Generator and often times you can input a very high frequency and yet see a much lower frequency at the output end. On the other hand you may be inputting a relatively low fr equency and yet witness a very high frequency at the output terminals. I believe that this is most likely due to this phase inversion and/or phase conjugation, and it is my opinion that this phenomena is responsible for exciting the very electrical valances of the nano-crystaline structures at the atomic level. A similar reaction can be verified as occuring in gas lasers at the photonic level when when a sufficient energy state and volume of photons begin to bounce around in the mirrored structure of the laser. I believe that the use of the unusual extra induction/input coils serves to provide the necessary phased inversion that produces these high electrical responses witnessed in the HOPE model. When the electrons become excited by the proper resonant frequencies and increasing electric and electromagnetic force is applied matter can literally fall apart. When the electron shells/valances reach a point at which they become unstable in the turbulent environment present in and aroun d a HOPE unit some of the electrons and in some cases proton and/or nuetrons can seperate from their otherwise stable arrangement. These liberated electrons, protons, nuetrons, etc.., will be influenced by the strongest force to which they are either attracted to or forced to repel away from. In the case of the HOPE model the route of least resistance becomes the output terminals for the most part. At the same time nature will always seek to right itself and find equalibrium, especially at the atomic level. When this equalibrium is disturbed to the extent that normally very stable atomic and/or molecular structures begin to fall apart nature seeks to replace those missing pieces with new particles of the same order. You may have heard it said by someone recently that energy is all around us. As Albert Einstein pointed out many years ago "Mass is energy and energy is mass". Some would say that these things all point to the alleged "Zero Point Energy Field" or perhaps you prefer the te rm "Sea of Energy" as remarked by Nikola Tesla. Since these are questions that nobody will ever be satisfied having answered by anything I might be quoted as saying I will leave all of that up to the so-called experts to deal with. I will never claim to be an expert in anything so long as I remain in this pitiful shell that we call a body because until our minds are allowed to fully join again with our spirit and with the Holy Spirit we will remain imperfect mortal beings. I am certain that a great many self professing so-called experts would disagree with me if nothing else but for the mere sake of disagreeing. All I can honestly say is that I have found that it is useless and a complete waste of time to try and argue with a fool. For those who seek the truth it matters not who is right and who is wrong but wherein lies the truth. If it is true that conventional physics and therefore electrical engineering are flawed then the complete truth lies somewhere else beyond that which the experts boast in their knowing. Mankind likewise is flawed due to his rebellion to the greater laws and interests of God.
It is currently my understanding and belief that it should be very possible to develop new materials which could be more specifically designed for HOPE tech application. I believe that we need to develop these new core materials keeping in mind that we are dealing with a number of various areas of art and science and which to my knowledge have never been considered to be used in conjunction with each other in this fashion. I also believe that this new knowledge may very well enable us to create the most conservative energy technology ever conceived of and which does not produce a radioactive waste byproduct. I have spoken to several very knowledgable EE's about this very idea over the period of the last month or so and they ha ve all stated that they see no reason why it should not be possible to create a technology that could conceivably provide a COP that could far exeed the alleged OU barrier. My research has lead me to look into various new highly reactive piezo materials which could conceivably be used in conjunction with high grade ferri-magnetic and/or ferro-magnetic materials to produce a superior core much better suited for this type of application, and which should logically result in output potentials far exceeding those we are currently witnessing so far.
As only one man there is only so much that I can accomplish without the necessary funding and assistance from qualified people. This work has been extremely slow and tedious, and without even the most basic of tools being available to me I have still been successful in learning a good deal about this new approach t o alternative energy technologies. I believe that with the proper tools and assistance we could have a fully developed new technology that could power everything from our cars and homes to future colonies on other worlds, and we could do this within a couple of years under the right conditions. I am only at the stage where this technology could provide nearly 100% of a homes lighting needs free from the grid but if the proper materials could be developed I believe that we could be seeing HOPE technologies supplying the power for everything else as well within very little time. I don't believe that this is a pipe dream at all. The only really big obsticles seem to come in trying to change the way things have always remained throughout our lifetimes, and the people need to have the sufficient desire to challenge the status quo and demand our God given right to true freedom.
Although there is certain information which is of great importance for anyone who may be conducting experiments with HOPE technologies I believe that it would be destructive to publish this information at this stage of development. There are those who would love to pose problems towards this effort and such information would very likely serve only to hinder rather than help progress in this area. I HOPE that the information I have been able to glean thus far has given you a better understanding of where this research stands at the moment, and what needs to be accomplished in order to develop this technology to a much higher level. I have tried to cover everything that I could think of at the moment however there are likely still many questions that will need to be answered as time allows. Please feel free to pass this information on to your friends and colleagues. I will try to keep everyone as up to date as is humanly possible for me to do.
Best Regards All,
Jim
James D. Fauble
jfauble@sbcglobal.net
Hi Group,
I was finally able to coax some information out of the engineer I've refered to in the past. He was pretty angry with me but heck, four months is long enough to wait for a few simple readings escpecially when he's the most qualified EE I've ever known of. I will post the info as soon as I have sufficient time. It's not great news, but I've tried to be honest and you all deserve to know the truth even if its sometimes painful. I'll get back to ya very soon on this so hang in there eh?
Jim
Jim,
I have an idea that may shed some light on some of the results you are getting with HOPE. :) I hope... haha
If I am repeating anything, I'm sorry. :-[
You have a jump in power output at certain frequencies - and I am assuming that you have not yet concluded why this is happening.
So I thought I might run a little theory up the flagpole and see if anyone salutes. ;)
I know this is not a LC circuit... but what you are seeing sounds alot like a similiar effect seen in a series LC circuit... so hear me out and think about how this might come into play - since you do have a rather "odd" arrangement of inductors in series in the HOPE.
**
In series inductive/capacitive circuits... When a state of resonance is reached (capacitive and inductive reactances equal), the two impedances cancel each other out and the total impedance approaches zero.
-and-
The total impedance of a series LC circuit approaches zero as the power supply frequency approaches resonance.
This can achieve 100-1000 volts from a 1volt power source - if the frequency is resonant to the circuit.
**
This may be waaaay off base. But hey - there's no math to explain what you've got there anyways, right? ;) This has to relate in some way.
Hi Guy's,
Well, ......... I have some good news and some bad news, and then some good news again, lol. First of all the good news. I was finally able to get some figures out of our engineering expert for the HOPE unit that I sent him more than 4 months ago. I know that it seems like you've all waited an eternity to hear the actual/true readings on the total power output of the unit that I have been talking about. It probably seemed much longer to me and I finally had enough of the waiting. I pissed the guy off and may have ruined a friendship and partnership in the process. However I figure that if someone as allegedly brilliant and highly qualified as this guy claims to be takes that long to give me a few numbers that it should take him such little effort to get, then I'm not so sure I want to work with a guy like that anyway. We don't have another lifetime to wait for someone to develop something which will enable us to free ourselves from the energy pirates and stop destroying the only planet we have right now. In the months of waiting I have gotten a good deal of negative mail suggesting that I was nothing more than a fraud or worse and I simply had to nip it in the bud before it caused people to lose heart in their own efforts and research. The bad news is that the readings that the engineer quoted were not what either of us had expected initially. For the past 6 months he has repeatedly told me that he is convinced that the device was surpassing the OU barrier. After waiting four months and paying him $400.00 I became tired of tryng to defend myself against all the accusations. I finally decided to be completely honest with my ISBP forum members and told them the real reasons for the extended delay to get these simple figures/readings. I did not disclose his name but simply stated that our alleged engineer had failed to provide any readings for us after waiting for four months. The guy's ego got the best of him and he came back revealing himself as the ass he really is. He immediately shot out some numbers and suddenly changed his tune saying that the HOPE was far from OU but that he had all the answers to how it could be made to reach the OU barrier. He came back so fast that I have to wonder if he really took any readings at all, and he said that $400.00 was not enough to even pay for the meter he required to get the measurements. And yet he was able to give us those alleged measurements only hours after my posting the real reasons for them taking so long to get. I put his name on the patent application for HOPE tech and gave him an executive seat on the board of the new company I have been trying to start up. Yet all I got in return was a slap in the face. He has his own idea's about the mode of operation concerning the unit that I sent him and seems to be stuck on the old-school way of thinking in matters of electrical engineering. He is afterall an alleged experienced engineer and I had trusted and respected his word and knowledge more than any alleged expert I have known. I would like to point out that he has agreed with me completely concerning the idea to develop more suitable core materials based upon my theory that there is a piezo-like component present in the Metglass cores that I've been using in my research. On the other hand he simply refuses to acknowledge this when describing how to improve the output with his updated design. It's almost like he has two different minds and a selective memory when he gets ticked off. I had suggested creating a torroidal shaped core out of the new piezo and high grade ferrous materials that I have mentioned developing, and now he's telling everyone that it was his idea. It certainly isn't the first time that someone has done this to me and most likely won't be the last. Personally, I find his behavior repulsive and unethical. My other new partner has done this with nearly every idea that I have told to him and is now apparently passing much of the information off on the web as being his own. Same ol - same ol I guess, and the more things seem to change the more they stay the same. I don't understand the mentality behind such behavior in people but to each his own, and who's going to care when were all dead and gone anyway. Just so that everyone knows, I have written the patent application for HOPE technologies in a specific mannor so that all current and future developments based on this idea will be covered by the existing international patent certificate. This means that as long as the U.S., military/government does not declare the tech dangerous to national security and find a way to protect the information under the guise of sensitive miltiary technology, anyone and everyone has my full permission to develop anything they like from of all this. I will gladly add the names of those who help to develop further designs and/or improvements to the existing patent and they will share the benefits equally with anyone else on that patent application. I see this as a good way to try and encourage others to do the same and share in the efforts and rewards while providing alternative technolgies to the real people of this world. I will spare the speach on how we all need to change our way of thinking in order to evolve to our higher potential because there are now many others who are already preaching that gospel. Finally, the good news regardless of the fact that the current model appears to be nowhere near the OU barrier according to our enraged engineer is, that if true, we can use the knowledge that we now need far less actual wattage to provide for lighting if nothing else. I have run several full sized 4 foot fluorescent lights/tubes throughout the entire evening and nightime until sunrise the following morning on a 9v DC transistor battery and still had a very good charge left in the batt. By purchasing a small PVC battery charger I can now fully charge that 9v battery in about 3 hours using the suns energy and run my lights the entire night completely free of the grid. I can use this even if nobody else see's the value of it and so I plan to use the remaining cores that I purchased to offer my folks free lighting as well. My step dad is a real penny pincher and will love me for it, lol. Anyways guys, at least we have what appears to be the information many of you have been wanting to know for so long. It's not what it appeared to be to me or the engineering expert up until yesterday but its still valuable information that should be posted. I am pasting the exact figures and remarks from our engineer directly below. I have deleted Bill's last name in order to protect his complete identy since he is afterall quite mad at me now, and I don't have his express written permission to use his name anywhere besides the ISBP os Project Forum. Personally I think that Bill's mind is going bad quickly, and he has reversed reality in his own mind concerning many events which he may honestly remember differently then how they actually occured. If this is the case it is a great loss to this community and I hope that Bill will choose to use his remaining time in the real world more wisely and efficiently while he still can. Bill see's me as having stabbed him in the back because I stated that our engineer had failed to give us any readings after 4 months of waiting. I don't know how much slack a guy needs to take a few simple readings with a proper meter and I was simply being honest instead of feeling like I had to make more excuses for Bill's failure to keep one of his many promises just once. Those readings cost me around $1,000.00 total which of course Bill selectively forgets. I don't know if Bill is intentionally lying outright because he is mad at me now but until now he has been the one telling me that he was convinced that the unit was an OU device and should have absolutely no problem closing the loop. If thats the case he is a liar either way in my book because he has a problem with being honest and forthright. Bill has also wanted a new RMS meter for a long time and I'm sure he can use it for many other things besides the couple of readings he took for us all. Don't anyone worry about this falling out between Bill and me over this stupid thing. If a guy feels the world owe's him that much just for one moment of his time to help towards finding some solutions to such an important thing, it's my opinion that he probably deserves to be in the situation that he is complaining about being in. One last thing, I have tried to get through to Bill that the introduction of magnets simply made no difference what-so-ever in the output readings that I was getting. I got the same readings with or without the magnets installed months ago on the unit I sent to Bill, and still get the same results on the new unit that I built using the same model core. Bill refuses to acknowledge any piezo component being present in the core material itself even though on the phone he has agreed 100% on the idea of making our own custom cores using the types of materials that I have suggested time and again. I understand a lot of things but I have never been able to understand people I guess. Anyway, enough from me eh? lol. You can read Bill's comments below.
Cheers All,
Jim
---------------------------------------------------------------------
Hello,
"I am Bill, the "alleged engineer", and Jim's business partner. I have tested the HOPE unit which he has sent me, and it does not break unity. In fact, it is far from it, with an input of 360 milliwatts (on one run) and an output of 36 milliwatts, which gives it an efficiency of 10%. It needs extensive reconfiguration to even break unity, which I am in the process of doing."
"What I found was a device that was put together on a purely intuitive level, with beautiful craftsmanship. I bought the required meters, most notably a 37XR True-RMS Multimeter with capacitance and inductance measuring capabilities."
"I found that the system was wired such that the coils had an inductance of 18 Henries. Guys, run your impedance formulas on that one at 2000 Hertz. I found that only one switching coil actually did anything, and it was in series with the output coils. Not a good idea. As a result of this, I had an output of 600 volts at around 3 milliamps on the first run with varying frequencies which seemed to center on 2000 Hz. Yes, that's MILLIAMPS, Jim. Check your range. Subsequent runs tested lower with fully charged batteries."
I tried to get the frequency down with the current configuration, but found that even when I disconnected the oscilllator, the thing wanted to self-oscillate at around the same frequency. I put balancing caps on the coils, but the impedance was still too high with that frequency. I asked Jim if I could rewire the model, and pulled the jumpers off and bought more materials from Radio Shack to power the coils and eliminate the feedback loop. That's where things stand now. Currently, the four coils on the outside are non-powered, and they need to have some kind of power input, possibly close to saturation. Also, the other three coils on the inside need to be powered as well.
"Here's the scoop, guys: What we're building is NOT A MEG! It is a modified Richardson generator, originally patented by Frank Richardson in tha 70's. Frank said that varying the reluctance of the two sides of the core was the key. He had a WORKING device in a VW in the 70's which he tooled around town with."
"Well, here it is, for what it's worth. Get the Richardson patent at the uspto.gov site, "Electromagnetic convertor with stationary variable-reluctance members", number 4,077,001, patented Feb. 23, 1978. Bearden's MEG is based on this patent. This patent holds the clue on how to fix the HOPE, and make it break unity. We need to SYMETRICALLY vary the reluctance of the core. One side goes high, the other side goes low. Flux follows the lines of least resistance, so first one side saturates, and then the other. Flux ping-pongs from one side to the other, and it ALWAYS sees one side with a low reluctance. Remember that, or your magnets will go dead."
"Why isn't it working now? Two problems: one, flux is not switched symetrically. It only has one point. I've been trying to get a magnetic probe to prove this, but so far the finances are not permitting it. Yes, I know, Jim. You gave me $400 dollars to work with, but that meter is $500. Until I can get some work in that'll have to wait. Remember I'm donating my time for free on this one, and cut some slack."
"The other problem is the metglas core. It's already in a low-reluctance state, so it's like trying to turn on a switch that's already closed. Look at the position of the internal coils, and contrast it with the Richardson patent. If you try to saturate the cores, you can't get any more output. SO we need to vary it from where it is, to a higher reluctance. We do this by powering the exterior coils... all of them. First one set switches on (on one side), putting the core into a high reluctance state, and then they switch off and two internal coils switch on-- on that same side.. Why do this? To get rid of the residual magentism in the core which will raise the reluctance. If some of you out there say that it looks like we're building an inverter, BRAVO! You got the point. We do this sequence first on one side, and then on the other."
"This is what I'm doing right now. If Jim decides he wants the unit back after releasing this information, so be it. You geniuses out there run with this and see if the theory is valid and let me know if it works. But remember the Richardson patent is the key. BTW: Jim, I told you about the problem with the core, and that a toroidal geometry would tend to fix this."
"It would look like the Greek letter theta, with the magnets in the middle. Doing this would also produce a rotating magnetic field. Imagine this as a rotor, and you get the idea. Also, the torus would vary the curl-free A potential, which you can do all kinds of wonderful things with much to the consternation of the EE crowd. So if Jim want's it back, fine. It's time to start on a new configuration. Also, I already have a working theory for a Coler device anyway that needs to be built, and it's being put off working on the HOPE. Jim knows this as well."
"I'll be tinkering on this tonight after job hunting this afternoon. Sorry if you don't like that Jim, but those are my priorities."
Take Care,
Bill
The attached pdf file is a paper which Daniel Jackson sent to me today and wondered if I would think it worthy of posting, lol. Daniel seems to understand the concept of my latest work very well and HOPEfully it will catch on with others in a big way (Punn Intended). Haven't had time to go over all of Daniel's work yet and I am not big on circuit design but maybe someone here can understand his circuits and explain them in common English, German, or whatever.
Hi de Lanca,
sounds impressive !
So you have a COP of 1750 ?
How is your Magnet-Transformer working ?
Some kind of overunity transformer ?
Does it use Neodym magnets ?
Simular to a MEG ?
Do you have a selfrunning system ?
Please let us know more !
Many thanks.
Regards, Stefan.
Hi de Lanca,
yes, of course COP=175 , was a bit late in the night when I saw this.
Can you post a picture of the device ?
Do you still want to patent it, or what do you want to do with it ?
Please let uis know more and when you expect to release more infos.
Many thanks.
Regards, Stefan-
LancaIV,
I just wanted to congradulate you on your success so far and encourage you to keep up the good work. It's to bad that these tasks are left completely up to individual researchers because we could certainly make a great deal more progress with the kind of tools and finances that the big boys have at their disposal.
Even so, it sounds like you are working hard with what you have, and if you've come this far already just remember to keep thinking of the very real posssibilities if and when you ever become discouraged. The thing about real hero's Lanca, is that most people never know what they've had to go through or what sacrifices they've made to try and help others. I don't even know you but, I know that if you are working hard to bring new alternative energy technologies to this world then you are a real hero my friend and I thank you.
Best Regards,
BushWacker
Hello Group,
Does anyone know of a specific frequency range used for spliting water into hydrogen? Several of us have observed certain phenomenon during HOPE operations and testing that could mean that a HOPE Generator may be able to be built to tune into the precise frequency range of any type of matter including water for the purpose of disasembling the molecular and/or atomic structure of that matter. If anyone does know of this specific frequency range please let us know.
Best Regards All,
Jim
Hallo BushWalker,
maybe this program can help you! It is based on a theory of elemtar resonance from Gabi Mueller
http://www.torkado.de/progs/Resonanz.zip
http://www.torkado.de/progs/progRauch.htm
http://www.torkado.de/elementarresonanz.htm
I HOPE it helps you!
for translation copy the adress to this site!
http://webtranslation.paralink.com/
regards
Norbert
Quote from: BushWacker on March 08, 2006, 02:03:57 AM
Hello Group,
Does anyone know of a specific frequency range used for spliting water into hydrogen? Several of us have observed certain phenomenon during HOPE operations and testing that could mean that a HOPE Generator may be able to be built to tune into the precise frequency range of any type of matter including water for the purpose of disasembling the molecular and/or atomic structure of that matter. If anyone does know of this specific frequency range please let us know.
Best Regards All,
Jim
Hi DeLanca,
how long will the patent proces take
until you can tell us more ?
Is your unit replicateable ?
Does it run all the time ?
Regards, Stefan.
Why do you want to patent it at all ?
Patents are no good at all...
Share the ideas and make money with being the inventor...
Regards, Stefan.
Hartiberlin,
How does an inventor make money by being an inventor and giving the information out? How does he/she get the reward back for their efforts?
In response to Hartiberlin:
that's pretty simple...
Am inventor makes money by being the very first able to efficiently and easily produce and manufacture his invention
or, to simply sell his patent to whoever wants top buy the rights to manfacture it
a patent doesn't protect anybody from unrestricted duplication
all a patent gives you is to make sure that you will be the one who will be the damn fool who will have to pay the attorneys to sue the countless duplicators while all the duplicators will have to do to win their case is to make a small modification to their unit so it is not 100% exactly the same as your patent, that's it, that's all
the best way in my opinion is to publish everything in the puiblic domain and by doing so it will make sure that no one will ever be able to reclaim a patent for it while you will be in full production far before anybody else
Hi All,
I haven't been able to make any progress on my 3D autocad construction of the HOPE generator, because I don't have access to AutoCad anymore. I don't know when I will be able to find one, so I'm posting what I have. I have the core and windings done, with some wiring.
BushWacker,
I have a simple idea, thats so retarded, it might just work! While I was walking to the post office to mail my mom her birthday present, I started to think about your post that I had read. You claim that you can run "several" "4 foot" fluorescent lights for a long time, using just a 9v battery. I realized that thats a whole lot of light, coming out of a 9v battery! So, why not use solar panels to capture the light, and turn it into DC energy! You could constuct long hexagonal, or octogonal tubes of solar cells, and then drop your flourescent lights right inside of them. If you have a hexagonal tube, with each side 2in by 4ft, then you would have 4 square feet of solar panels per tube. If you had "several" fluorescent lights with hexagonal solar panel arrays around them, then couldn't you generate a lot more power than a 9v battery? The output of the solar arrays could be fed into simple resistors and transformers to make the input voltage necessary for your audio amp circuit. Therefore, you would just need the 9v battery to jump start the HOPE generator, and then let the solar cells take over. I included a simple diagram in the attached archive to aid in visualization.
This sounds like a decent idea, but there are a couple Unknowns that maybe someone could answer.
1. Do solar cells work as efficently under fluorescent light, as any other light?
2. Is the HOPE Generator lighting the fluorescent bulbs up to their full brightness?
3. Does the HOPE Generator alter the light so that a solar cell would not work as efficiently?
'HOPE' this helps out, either by allowing the loop to be closed, or by 'ruling out one more way that doesn't work'.
Best of Luck,
Jin
Hello Jin,
Your idea isn't dumb at all, and in fact that is very close to what I have been doing. I purchased a small 9v PVC battery charging unit that fully charges a 9v batt in approximately 3 hours time when the battery is completely drained. However I can run the fluorescent lights throughout the entire night on the 9v battery and hardly notice any loss in its charge in the morning so it only takes two hours at most to charge it back up to full capacity. The solar cell or (PVC) measures only 3.5" x 4.5" so you can see just how little power is needed to light several fluorescent lights throughout the night.
I am sending a HOPE unit to an independant researcher in B.C. since I don't believe I can trust the guy who was originally supposed to be doing the technical write-up. This new guy has no ties to me and has nothing to gain or lose by giving me false information and is simply very interested in knowing the facts.
I am now building several larger units using the AMC-1000 C-core so we'll have to see how things turn out with the new models.
Thanks for sharing the logic Jin. I'm glad to see that common sense is still valued in some places, lol.
Best Regards,
Jim
Hello LancaIV,
I've kept up with all the patent laws for the last 3 decades both here in the U.S.A., and International patent laws. Though there is some truth that a patent will not necessarily protect your idea from being marketed and sold by others, it will give you some exclusive rights none the less which will protect you if you plan to sell anything in the future.
There are some recent changes in the International Patent Laws that include nearly every major country and these changes are protected under the International (PACT) act which went into effect in the year 2000 and was more recently updated in 2005.
Any International Patent will give you patent rights in the U.S., as well as all the other major countries around the globe. A patent for HOPE technologies would have cost me a base minimum of $10,000 USD here in the U.S., and probably would have gone for closer to $20,000.00 to $30,000.00 by the time all the lawyers took their cuts.
My boys and I checked around with a lot of patent attorneys and did some research and found that an international patent can be secured for a maximum of $350.00 USD. Guess which way I went?
Under the new PACT act you can now file a patent outside most major countries and by going through the patent office in Belize you can secure yourself a patent certificate for next to nothing compared to what it would likely cost you to file in your own country. All the rules are the same as well as the protection of the patent. The only difference is the money you spend to get the patent. Just be sure to ask to file a "Patent Utility Certificate" otherwise they may try to run you through some hoops to get more cash out of you, lol. Good luck LancaIV.
Cheers,
BushWacker
Hi DeLanca,
schade, dass Du nicht mal ein Bild von Deinem Ger?t zeigen kannst, wenn es Deine Gl?hlampen
antreibt....
Wann kommt das denn mal ?
Gruss, Stefan.
Hi LancaIV,
I don't speak German and so I cannot understand many of the conversations lately but from what I can gather it appears that you have something together that is showing possibilities as an alternative energy technology. Would you mind sending me some diagrams and info on what you are doing if you have anything on paper? BTW, the partnership that I had formed has been suffering from extremely poor communications also. This seems to be one of the major problems in trying to form partnerships with people who live long distances from each other. I am only now able to get back to work on my HOPE R&D because one of my partners had held onto the unit for nearly 6 months and did absolutely nothing during that time. The figures he gave cannot be accurate and it turns out that he is still completely clueless about how the technology works. Anyway, if you woudn't mind sharing some information with me I am very interested to see what you've got so far. If you don't feel comfortable sharing anything at this time however I can understand also.
Best Regards,
Jim
Hi Lanca,
Would you check Paul Galey's patent number because what you wrote in your previous mail (FR7515840) does not exist. Maybe you meant FR2312135 ??
Rudolf Kroll has also got several patents, which one you meant? Maybe DE3938577?
Which patent (Galey or Kroll) gives higher output in theory in your opinion? You seem to favor Galey's arrangement?
Thank you,
Gyula
Hi de Lanca,
do you have a pdf version of patent FR2312135.
Best Regards
Joerg
I got the french version. Do you have an english version?
Looks similar to the MEG
Best Regards
Joerg
Hi Guys,
I have attached the latest updated basic configuration for a HOPE Generator. Instead of leaving one end of each of two of the input coils unwired I have found that in most cases there is an increased efficiency when these wires are connected together and linked to the input. Take a look at the drawing and you will see what I mean.
In most cases this seems to be the best way to wire things although I have assembled a couple of units that had to be wired with the input coils connected to the corresponding coil on the opposite side. There doesn't seem to be a predictable way to know how a particular unit will function or how it may need to be wired to be the most efficient. I have recently built three identical units with the only slight difference being how tightly the coils have been wrapped/wound.
It seems that contrary to my thinking, the coils which have been wrapped more tightly do not work as well as those which have been wound more loosely. This goes for both the input and output coils! I have no explanation that makes much sense to me at this time but I have double checked this to make certain that this is in fact the case and it definately seems to be. The difference in output can be as much as 600+ VAC so this is no small note to make for those who may be building one of these devices. Keep up the good work LancaIV.
Best Regards All,
Jim
hi,
i am not good at electronic so here my question/suggestion
for a better core instead of using what you are using, that would not be better to
built your own core using Amorphous Metal, they react faster to magnet field and
using glue they will probably be cheaper then a standard metal core?
I am currently using an "amorphous metal/glass composite" to build the various models of HOPE Generators. I have so far only used C-core style cores made of this material by Metglass Corporation. My latest model was built with the intention of utilizing AC current directly instead of sound/audio signals which needed to be created by using a small electrical source of origin anyway. The new unit will still convert audio signals directly into AC current but with the limitations of having to use the same old materials I have found that using a small AC input directly gives me a better overall energy coefficient/COP.
I had been trying to convince one of Metglass'es distributors to help me to obtain enough of the raw ribbon/tape material that Metglass makes their AMCC series cores out of but Metglass is treating it as a special order and simply wants far to much for a small amount of the ribbon. The idea was to purchase the amorphous ribbon and some LZT (Lead Zirconate Titanate) from EDO Corp., to dope the ribbon with. A small DC current would be applied along the ribbon over a short distance at a time while a slow drying epoxy/glue would be lightly applied to the ribbon. The LZT nanocrystaline Powder would then be sprinkled onto the ribbon and the crystals oriented in a desired direction by means of the DC current. The ribbon would gradually be rolled into a torroid shape until the desired core thickness was achieved and the new hybrid core would then be allowed to dry/set.
Since the amorphous composite material already shows a response to sound resonance the crystals should increase the response by many factors. The idea was to enhance both the magnetic and pure resonant qualities of the original core material with a highly reactive piezo material to increase the electrical response. Because the LZT crystaline material reacts to both electrical and/or sound resonance I felt that it was logical to assume that the addition of such a material could only increase the output potential of a HOPE style assembly.
Unfortunately money has once again thrown a wrench into the works and I am again unable to go any further. BTW, my latest HOPE model is showing output potentials of between 100 to 150+ times the energy input in volts. The multiplication factors will depend on the waveform and type of energy input but any type of resonant energy can be utilized and converted directly into AC potential. For instance: if I put in say 9v AC even at very low mA levels I will see well over 1000 volts on the output side. Remember that that is 9v AC not DC! If I split 9v DC into 18v AC you would see somewhere around +or- 2000vAC at the output end. This is plenty for providing fluorescent lighting of several full sized fluorescent lights so that is what I am using it for for now. It may not impress to many people but try to find any product on the market that provides this kind of lighting with so little energy. Hey, if nothing else it might interest some hermits or pot growers out there eh? lol
Cheers,
Jim
you cannot use magnetite and use epoxy to build you core? i am not sure if Amorphous Metal is made out of this material, but some used magnetite to build coil core instead of metal and get better result, you can buy big bag of magnetic on internet, its something to try out :)
Hi (The One)
Thats interesting, I haven't heard of anyone using Magnetite to make cores out of. I will try to find some info on that. There are many things a person could try if they have the proper equipment available, and I suppose that I may eventually have the opportunity to create some cores from scratch using various raw materials but right now we are trying to sell the house and there isn't any place to fire up the kiln or even an area to work at other than the floor or one small card table. The overall environment around here is not beneficial to conducting any sort of research either as my folks are in their mid-eighties and pretty much losing brain cells in massive quantities lately, so they keep me pretty busy..... lol.
It appears that I am going to be the only one to take care of them through their final years, and being that I am disabled myself, its going to take every ounce of strength and patience that I have.
God only knows if anyone will ever pick up where I left off but I can only hope that someone will. I really think that the addition of the proper mix of piezo materials with the right core material/s may allow us to break unity by a fair margin but it will likely wind up being someone other than me who will have that honor. If anyone out there wants my help in pointing them to various suppliers or for tips on anything I am more than willing to help. However I have spent every penny I had on my research and have been unemployed and unable to work a regular job now for 11 years so the buck stops here as far as my work goes on HOPE R&D.
I hope that someone will be encouraged by what we've learned from this all so far enough to carry on along this line of R&D because I truly believe that we are ver-very close to seeing the true potential of this kind of technology. I wish I could try Magnetite as well as a good number of other elements and various combinations but it has proven to be far to expensive for one unemployed guy to afford, and much to time consuming as well when you have several geriatric children to take care of.
If anyone does decide to look into this approach further and experiment with piezo powders and various magnetic materials etc.., etc.., I recommend that they start from scratch and stay away from big corporations as much as possible! Before they will help you obtain any materials they have to know what exactly you need it for. Then they will leave you broke, take your idea's, and leave you in the gutter.
I wouldn't be suprized at all to see one of them suddenly come out with an allegedly new idea/invention involving piezo enhanced cores for power applications and/or alternative energy. Most likely though the alternative energy tech would go to the U.S., military and never be seen by the public again.
Oh well, this is startin to turn into a novel so I'll shut up now, lol. I guess the best advice I can give to someone is,......... if you know that you know that you know something will work even though nobody else has a clue about what you are talking about, go for it because thats the way most new discoveries and technologies come into being. Don't worry so much about the current theories in physics as long as you have a good working knowledge and understanding of the basics.
Best Regards All,
Jim
Hi Group,
A quick note for anyone looking to further R&D of HOPE Tech. I have uploaded a pdf file in the "Material Supplies" catagory located on the home page of this forum. This file shows a chart comparing the various highly reactive electro-ceramic/piezo powders which EDO Corp., alone offers (http://www.edoceramic.com/). These are piezo nano-crystals which appear as powders but are among the most highly reactive piezo materials available to the public today. Look at the various uses for each grade of powder to determine the best choice for your application of it. I strongly believe that someone out there is going to become extremely wealthy by successfully applying these materials to our current MEG, HOPE, and other transformer type power technologies. Think about it and see if it doesn't make sense to you!! Just continue to keep it quiet and watch your backs guys.
Best Regards All,
J.D. Fauble
Hello,
I have been reading about this device but have not seen any drawings. I have good lab in my home. Scope, meters, function generator, tons of parts CAD package etc. Lots of electronic experience.
I would like to contact the enventor.
I live in Canada.
Mike
Hmmm interesting device you have here.
Please Note:
I have been trying to post the following message for the last several days. Every time I try my browser is shut down. I will attempt to upload the final revised "HOPE for the Future" .pdf file under the subject heading "HOPE Testing". Therefore please check there for this file if you are interested.
Jim
-----------------------------------------
Hi Everyone,
I appoligize for appearing to have disappeared. We have had some major problems with everyone being sick around here for the last 6 months. Numerous hospitalizations with pneumonia, blood poisoning, MRCA, abscessed teeth, etc.., etc.., and the folks need a lot of help getting along each day anymore. Anyway,........ I am attaching the latest and hopefully the final revision of the "HOPE for the Future" Construction, Assembly, and Basic Information paper for those who are interested. I completeing forgot to remove all mention of permanent magnets from the former copies and of course later discoveries showed that magnets actually serve no purpose at all in the HOPE Generator design.
I would also like to point out once again that I am not nor have I ever claimed that the current HOPE model is in fact a "Free Energy Technology", and I can only hope that people will make certain that they don't go telling others that I am making such claims. I visited Sterlings PES website just an hour or so ago and it appears that he has once again taken the liberty of mis-quoting me for some reason. I have been attempting to get through to Sterling by e-mail but once again my messages are being rejected so if anyone feels compelled please ask him to remove the claim of free energy in reference to my HOPE Generator. For any of you who would like to contact me you can write me at jfauble@sbcglobal.net and make certain to write HOPE 4 Me in the Subject line so I'll know that it's not just spam.
It would be very nice to talk one on one with those who are interested in this discovery and I believe we might actually be able to make more progress than this environment allows. I would also like to take this time to say that despite the fact that Freedomfuel has been a bit of a thorn in my side at times that he has been right on about 90+% of everything that he's commented on in regards to his theories on why the HOPE Generator functions as it does. Freedomfuel you have a fairly keen insight on many things and you have been instrumental in giving me some idea's about where to go in redesigning future HOPE models to function even more efficiently. In particular your thoughts on rotating magnetic fields as well as the "Earthquake Lightning" theory are very perceptive and I believe that you have a very good understanding of what is going on to cause the results we are seeing in a HOPE Unit.
I have decided to make the newly revised "HOPE for the Future" paper available to this forum and a very few others who have shown genuine interest in this phenomenon. I only ask that you restrict this information to yourselves and other members within this forum unless you first ask for my consent to share it with others. Also, please remember that though I am not claiming that HOPE is a free energy technology yet it certainly appears to be closer to it than anything else I have seen in my 30+ years of research, and I am so sure that it can be further developed by using the knowledge gained through experimentation and some of the insights that perceptive people have already shown in this forum.
After many attempts to reproduce the claimed results of Tom Bearden's MEG Unit I knew that there had to be something wrong with the picture so-to-speak. Remember that permenant magnets are not required nor do they serve any purpose in the HOPE design, and very small audio signals can produce even higher voltages in a HOPE Generator than anything that has been claimed with a MEG. I have learned a great deal through the last 6 to 7 years that I've been building these kinds of devices and I think we now have much more solid information to explain the undependable results that have been reported by most MEG builders. Freedomfuel already seems to have a very good understanding of the physics involved and that is quite impressive to me since he has never had the opportunity to personally examine or experiment with an actual HOPE Unit. BTW Freedomfuel, I have signed out of the ISBP OS Project and if it is going to be reproduced someone else is going to have to head it up and fund it. I hope you are satisfied, and I completely understand your concerns as I have had the same concerns. To bad there are so many evil people out there who can only see weapons instead of the tools to heal that we could have.
I'd like to share something else with you all that I doubt that anyone here has considered. Does anyone know who Stanley Meyers is? I'm sure that some of you do. Stanley Meyers discovered a way to use high voltage (HV) at very miniscule current levels to split large amounts of hydrogen and oxygen from H2O instead of the other way around. Meyers used a ramped DC pulse frequency to accomplish this task. One of the reasons that I see the discovery of the HOPE phenomenon as exciting as I do is that I can see how Meyers technique might be employed using a properly designed HOPE Generator. It should enable a person to get by with using far less actual power to achieve the same results. Since a HOPE Unit actually opperates better or at least as well on audio signals, it isn't difficult for me to see how these two pieces of the puzzle might fit together. Okay, so some might say that the difference is that a HOPE Unit puts out AC when Meyers used DC. So has anyone ever heard of a rectifier? Well, it just so happens that one of the other things that I haven't mentioned so far is that there is another very nice thing about a HOPE Unit that should come in handy for this application. That is, When you rectify the HV AC coming out of a HOPE Unit you get the same voltage in DC potential. I know that some of you will probably call me a liar, and I know that thats not suppose to happen but it does with a HOPE Generator. There are a few other phenomenon and anomalies that myself and others have witnessed but I sure don't want to get into anymore arguments with someone who assumes that I'm either off my rocker or just some idiot who doesn't know what I'm talking about. Been there, done that to many times to count and you can't prove anything to someone who knows everything without ever seeing anything.
The only thing I don't like about what I see happening with a HOPE Unit is that no matter what kind of waveform you put into the thing, you always get a sine wave at the output end. So far I haven't been successful at remedying this and I would prefer to be able to see the same waveform coming out as I am putting into the unit. However, I'm confident that some of you already know how the waveform could be converted into a square wave, a triangle wave, or whatever without changing the voltage potential or current value to much. Unfortunately I'm no expert on microcircuit design and I admit that this has been my biggest problem in determining whether or not its actually possible to close the loop on any of my current models.
In closing I just want to mention that I have tried to post this message a half dozen times over the period of the last several days and every time my browser is shut down. I never have the problems that I have trying to surf or post anything anywhere else on the Net so whatever the problem is, it seems to have something to do with this site in particular. I've had so many problems with trying to browse or post anything here that I begin to stress out even before I attempt to log in. If anyone else is experiencing the same or similar things please let others here know so Stefan can look into it. Have a great week everyone and I hope that this information will help to enlighten someone at least a little bit.
Cheers,
Jim
Quote from: BushWacker on July 23, 2006, 02:27:11 PM
If anyone out there wants my help in pointing them to various suppliers or for tips on anything I am more than willing to help.
Why not just post everything to this forum, so there is a public record of it?
Hi Fred,
I can't really think of much that I have not posted already. If you will take a look at the last revision of the "Building HOPE for the Future" .pdf file that I was finally able to upload earlier this morning under the subject (HOPE Testing) you will see that I have listed where the hardest to find materials can be found under the heading "List of Materials". If there is something else that you are trying to say or something else that you are having difficulty locating please clarify.
Regards,
Jim
Hello BushWacker
I would like to try and build an Original HOPE Gen and a toroidal configuration you talked about. First would be the Original to understand the working of this device.
The one thing I am stuck on is the connection to input on the lower deck to the source . I missed something along the way.
I found this dealer on eBay selling rolls of Metglas nanocrystalline tape.
http://cgi.ebay.com/Metglass-nanocrystalline-tape-for-MEG-generator-5kg_W0QQitemZ250137739830QQihZ015QQcategoryZ1267QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
He seems to stock this stuff so I am under the impression he has a lot of it in many different sizes.
Hi Jim,
I would like to suggest, if you haven't tried already, try a "pulsed" audio wave at a 50% duty cycle. One of Meyer's components was a pulsed input. So what does a coil do when it's pulsed? I am quite curious. Thanx!
http://zeitwort.at/index.php?page=Thread&threadID=5882&highlight=
Hi! What happened to Jim? Do we have any news? I tried to contact him using e-mail but it seems that his address has been changed, jfauble@sbcglobal.net is not valid anymore... :( :( What happened to his device?
Still no word from Jim?
I hope he is still alive and well.
Has anyone duplicated this device of his yet?