M.A.M.K.C
stands for
magnetically activated motionless kick coil ;)
out put far excedes input....
more to follow...
ist
this is my ss non mechanical battery charger... ;)
it can be made variable ;) to tune it to correct freqs...
the device i spoke of
ist
Hi innovation_station,
Nice, I have also seen the SSG wheel as a commutator, it has nothing to do with much of the concept. The spinning vortices induce noise in his circuit and a low level output for his timing signal.
Great work,
Take care,
Michel
well did some tests on this unit it runs fine no heat or crap like that
makes noise annoying..... freq must be higher currently set adj 100ohm - 5k problem at 5k...... pot melted down over a long peroid of time have to work on that ....
in put 12vdc solar battery deep cycle output battery is tied to primary 1 feed and 1 return
out put is 100vdc and 33vac after a bridge rectifier b4 bridge dc volts are 70vdc peek it flucuates a wee bit .....
after 1 hour of run time all i could read from my primary was a decrease of .01v i did not mesure the charge ...... no need when it is connected to the output battery i usualy get an incease of .4 v across my out put battery how ever i found for some reason a hv spot in the system i have been shocked 2 times from this unit....
the last time was verry intence both arms can you say NUMB...... oouch!!
the really odd thing was this..... i was fiddleing with a termanal on the feed bat and a termanal on the out put chargeng battery ........
at the same time .....
just too strange.....
be careful if you play with this unit.... it bites darn hard
ist
i was able to get this to run on a 9vdc battery ....
also added a 10 k pot.... works ok on the lower voltage so far
i was able to tune it to a sweet spot of the coil .....
]
how do i know?
my 120vac 3ma max n2 with a resistor across it lit up else where in the freq range no lite......
ist
ok also i notice when it stops working loose connection or somthing.... YOU MUST SHORT THE COIL ON THE PRIMARY FOR SOME REASON B4 IT WILL START AGIN strange..... this device is verry lould as in you can plainly hear the coils sound.... when you turn the pot
i did not mesure the freq of the sweet spot i suspect it is lower freq...
ist
seams tricky to find with a 10 k pot hummmmm the sweet spot
Re:
Nice piece of work so far.
I do believe like Tesla that HV/HF plays some funny tricks on coils, wires. You loose resistance and gain in performance.
Be careful as flashing a coil can produce hazardous radiations. Use a mini Faraday cage grounded to a water pipe.
Take care,
Michel
in playing around today i have come up with a better device....
it is called IST MASSIVE MOTIONLESS KICKER COIL
1 ferroite ring from an old tv the 2 part kind
3 microwave oven transformer primaries ....
i have mesured over 1875 vac upon return with a single pulse by hand....
ist
now to charge a cap with it ....
Quote from: innovation_station on August 24, 2008, 06:25:14 PM
in playing around today i have come up with a better device....
it is called IST MASSIVE MOTIONLESS KICKER COIL
1 ferroite ring from an old tv the 2 part kind
3 microwave oven transformer primaries ....
i have mesured over 1875 vac upon return with a single pulse by hand....
ist
now to charge a cap with it ....
this coil is so kool it gets its own thred.....
ist
Anyone have a picture like drawing or schematic on the setup with a materials list this seems fairly interesting and apparently it is turning results I just wonder where this may go either way thats for not letting a good thing die.
-infringer-
Quote from: infringer on August 25, 2008, 12:33:08 AM
Anyone have a picture like drawing or schematic on the setup with a materials list this seems fairly interesting and apparently it is turning results I just wonder where this may go either way thats for not letting a good thing die.
-infringer-
you bet ;)
ok so i now have a hd cam 11 mp so i will shoot a video of this unit in operation also there is somthing else i do with this unit that i may demonstrate in a video ... CONVERSION i have used a 9vdc battery yesterday on this unit in a demo... and i charged up a lawn tractor battery the lawn bat was 4.20 vdc and the 9v was 9vdc so it ran 2 min on charge and i mesured the power in the tractor battery it was 12.12 while being charged...
then i disconnected it and it droped gradually over time of 30 min and settled at 5.5vdc
neet :)
any how lose the tractor battery .... drop a cap there to see real magic ;) i have done the same as above but i shorted the cap with a scewdriver as fast as i could constant hand shorting quite fast actually but
you know what???
the power was always there...........
been there all along........
ist
here is a pic of another coil i made ...
ist
here is my coil hooked up to a cap it will charge this cap to 224 vdc and it will not charge it higher
the other pic is out to the meter
this thing will run weeks on that battery....
ist
Quote from: innovation_station on October 16, 2008, 11:32:33 PM
here is a pic of another coil i made ...
ist
Nice.. Is that a joule thief on steroids?
much similar yes .... but no!! lol
it is a bedini motor - the motor lol
ist
;D
so we have the battery we have the coil unit we have the cap
we will add to the string of things a step down transformer from a 12 dc car battery charger...
and we will SLOW DOWN the speed and IN DOING SO we in crease the amparage ;)
get it
you now have far more engery in the system than it took to start and maintain the process
WELCOME TO CONVERSION
ist
out put is a fast battery charger 8)
once the engery is in the battery
well ....
so i have come up with yet another design this will have mutiple coils.... to increase output keep safe ... NONE OF THEASE ARE CASCADED.... im only amping once!!!!!! but x 6 coils.... do not cascade this !!!
this is your WARNING!!!
i hold no RESPONSIBILTY FOR WHAT YOU DO!! remember that!!
ist
im building the driver board now 6 channel....
i will post when it is finished or worthy of a picture..
a sneek peek at the ist 6 pac 8)
this is 1 of many ways this can be done ;)
ist
ist 6pac controller board ready for solder
ist