Kapanadze Cousin - DALLY FREE ENERGY

[T-1000]

I am not sure why it is so confusing about coil winding. Again, lets say we start with clockwise (cw):
a) Layer 1&2 like in conventional coil starting clockwise;
b) Layer 3&4  ccw - opposite direction to layer 1&2, started from the half of length of 1&2;
c) Layer 5&6 cw - opposite direction to layer 3&4,  started from the half of length of 3&4.

[Tomtech29]

Hi Jeg,

In view of T1000's reply (that he can only go on the old conference notes) and John.K1's post saying that Ruslan corrected himself by saying the winding that way (old way) de-stabilize the system and reduce the power, IMO it makes sense to go for a uni-directional winding.

Hi.
I hit sunk the whole truth about the construction of the coil Ruslan repeatedly confirmed that its new coil is wound like a conventional transformer
and he heard it also says the old configurations and admits does not give him such an output current
already I touched upon this issue in another post but no one pays attention not It recognizes something that everyone should establish and to stick to the one in left and one in right and there is a road to nowhere

Now to the crux of the coil :beginning or in the CCW or CW, there is no difference! -only antenna and bifilar coil is to be in the opposite direction.

Lay down 24wdg issues.? 12wdg. ? This latter two layers determine the inductance of the coil and thus change to the high level of high-frequency resonance.

[T-1000]

Hi.
I hit sunk the whole truth about the construction of the coil Ruslan repeatedly confirmed that its new coil is wound like a conventional transformer
and he heard it also says the old configurations and admits does not give him such an output current
already I touched upon this issue in another post but no one pays attention not It recognizes something that everyone should establish and to stick to the one in left and one in right and there is a road to nowhere

The way of winding you are proposing will have opposite effect than was intended for the lowest inductance as possible and high frequency passing through transmission line. It is not ordinary transformer to play with and the standing waves are reached only when reflected wave comes back to place.
In your setup the inductance will be too high for RF. Also not sure if you ever hit effect of power amplification with this.

[Hoppy]

The way of winding you are proposing will have opposite effect than was intended for the lowest inductance as possible and high frequency passing through transmission line. It is not ordinary transformer to play with and the standing waves are reached only when reflected wave comes back to place.
In your setup the inductance will be too high for RF. Also not sure if you ever hit effect of power amplification with this.

Theory and practice don't always go hand-in-hand, so its wise to try both methods. Tomtech is confirming here what John.K1 has posted. Given that none of us have so far achieved a self-running device or are one hundred percent sure about the real principle of operation, we only have Ruslan's word for it and as he is saying that he has gone over to a uni-directional wind for better performance, then I would favour first proceeding in that direction.

Tomtech raises a good point above: Lay down 24wdg issues.? 12wdg. ? This latter two layers determine the inductance of the coil and thus change to the high level of high-frequency resonance.  

[lost_bro]

Hi Dog-one

And now take a look at what Akula said about the induction coil between tesla and it's antenna. He says that the inductor creates sharp edge pulses (from sinusoidal output of Tesla coil) which is like a hammer on the wire of collector (or what ever you call the coil below). I only repeat what he said about his device

Bro: have you some nice program for Arduino and AD9850 you can share?  - I have both too. Just a programming is what makes my pain in an ass

Good day John.K1

More than happy to share my work...... This can be used into the MHz range.

Please find attached the 'Sketch' for my AD9850dds & ArduinoUno with variable duty cycle control with hardware hack.

The schematic for the hardware hack of the AD9850dds (chinese pcb) is in the DSO file.

See attached pics. for AD9850dds pcb.

take care, peace
lost_bro

EDIT,  Forgot to attach the library file *dds* for the DSO.  Please find attached to this post now