Kapanadze Cousin - DALLY FREE ENERGY

[Zeitmaschine]

My 100Hz saturation wave looks like this. Now I'm not sure how to get something useful out of it.

[Hoppy]

Hi Nick ,
You havent't heard and you will  not ear anything because i dont talk about my personal work  but it runs very well Nick thanks for ask .
Auto sustained circuit is not the goal to me  because i already reach that , but how to  improve the actual  rate of Power output is my actual main goal.
But in general im happy with results until now .

Sometimes i like snich in tread 😁 to see the news !

Hope things run well to you
Best luck

Hi again Nelson,

As you are now self-running perhaps you could toss us a paddle on your next snitch-in.

[Jeg]

Hi Verpies
I took a look to my car-amp and indeed has a 2 Ohm output. So I 'll give it a shot.

In relation with the mustache like waveform, is for synchronizing the current peak with Kacher's HV. At least this is the Akula's way. But Allega's, blue box which is improved by Itsu is a real gem for experimenting.   

[NickZ]

Verpies:
You mentioned:," a "push-pull" is a type of amplifier topology (B or AB class usually").

My point in all of this is that it is unimportant how the proper signal is generated.  There is nothing wrong with 74HC4046 or TL494 but it is not special.
What's important, is how the yoke or grenade or split pipe or ferrite rod, etc. react to this signal.
                                                                                                                                  end quote.

   It may be unimportant how the proper signal is generated, but, the meaning of what is actually a "proper signal", is still a very illusive term, or idea. As well as just how to generate that signal "properly". 
 
   I also feel that what you are mentioning is in theory how it should be. But is it, really? In the case of the Ruslan/Akula devices.

   To test the idea, I built up my Mazilli/yoke/grenade/Kacher combination.  First tuning the induction circuits to their best output, and trying to tune the Kacher to be in sync with the 3 turns coil/induction coil.  Not easy, especially the part about seeing any  additional output from this mix, than what was provided by the input, from a PS.
   
  I am not partial to any of this type, or that type of device, as long as it's a solid state, non moving, (no noise), type of thing.
And so, I'll continue on,  "come hell or high water".  Looking for the magic, in the device.

   BTW:  I feel that the yoke/grenade coils are neither a donor, or producer, or even having anything to do with NMR.
But, it is something similar to a transmiter/receiver, device instead.  Kinda like a magnetic antenna that can both transmit a signal, and receive back from the ambient, at the same time. Without having to burn itself up, in the process, like with NMR, to do so.
  And I plan to prove it.  Or, to disprove my own ideas.

[AlienGrey]

Hoppy
quote
Bedini knew and stressed the importance of Barium ferrites but never revealed details
snip ,
One possible source I read about way back was that barium ferrite was widely used back in the 50's, 60's as medium / long wave aeriel rods and for magnets in loudspeakers
end quote

Sound systems HUH ?? the lineage of the TPU was speakers !

Steven Marks }TPU} made a discovery playing with speakers ... which lead to the TPU



Needs serious looking into, source, Home remedy [options for home assembly ??] then a simple test bed and experiment ..
I could take this itty bitty experiment down to Wesley for some " itty bitty test runs" ..

No stone left unturned...


@Nelson
Thank you

Chet

Long wave aerial rods, had a pile of them to play with my self, they are strange in swome ways, you can get them at Maplin Electronics for 2 or 3 squid think they have loads of them.