Kapanadze Cousin - DALLY FREE ENERGY

[AlienGrey]

Yes we did make a device (grenade using Aluminium foil) rather than a winding, this killed any effect at the time of testing, however it might be possible to wind a 1/2 wave experimental winding on a 45mm tube and place in the centre of the 50mm tube, with out knowing any details, however that didn't stop the effect on the original.

What we need to know is is it 1/2 or 1/4 wave of the 38meters or a wave concerning the Katcher assembly it's in tune with, I do so hate having to spend time and resources to reinvent the wheel when some one already has the details they might like to share

Any one ?

[NickZ]

   T-1000:
    Well, ok Geo doesn't have  a self runner. Sorry to hear about that. I was hoping that he'd hit on it by now.
So, no worries, I'm slow at this also.

    Guys,
    I made a couple of new videos late the other night and below are the two new links, to them.
   The first one is about showing possibly what might be some of the first signs of "effect generation:, without going into the caotic mode. With peaks maintained below 230v, or so

   The second video below is showing what may be the first part of the "effect" that is needed to get this thing off ground.

   https://www.youtube.com/watch?v=ofA-rtYe9hM
   https://www.youtube.com/watch?v=qO1wKH3CnIA

    The scope shot pictured below, is of the frequency of my drain signals at the time of running the "effect", 15KHz, and a few other important details in that digital scope shot. It shows when it rings into the caotic mode, but only with the induction circuit running, no Kacher on, on that shot. It's just a shot of my drains signals, on one of the sweet spots where it sounds like someone is trying to tune into Radio Moscow.
Or something like that.

    That scope shot below was taken tonight, on my new Siglent scope. Which is new, and it's great, and it's pretty.
And it's here, with me now. I took a screen shot picture of it, of my drain signals, from my cell phone for now.
And I'm sure glad it has the button called "AUTO", or I'd be lost in scope land without that button.

   I have to thank Dog-One, for his contribution of the Siglent scope. It is very much appreciated. And it got here to C.R. in like new condition, and it also came very well boxed. So much so, that I had to convince the customs duty guys here, that it wasn't a brand new scope, in its original box. When it was...
    An amazing gift...
   Thanks again Dog.
   No more blurry scope shots...
   Well, maybe just a few more blurry ones from my old Tectronix, at times, as it may still have something to show.
                                                 
       NickZ

[Hoppy]

Nick,

Please show the mosfet gate waveforms in both normal and chaotic modes.

[itsu]

Nick,

the new scope looks awesome, take good care of it.
It shows nice signals with about 50V amplitude and a spike with a 333Khz (3us) ring on it.
Try to put the left markers (yellow 1 and blue 2) on the nearest horizontal line to better compare them.
Off course on the right side of the screen you can put up some measurements data like frequency, Vpp etc. but you will pick up on that soon.


The first video shows great operation, nice steady drain signals (despite the spike and ringing) and the additional brightness of the bulb
when the kacher kicks in.

The second video nicely shows the effect you get, but overall its not a that bad signal on the drains, i have seen far worse signals in chaotic mode.
The sound (about 2Khz??) tells that probably you have some oscillations going on back into the TL494.
Some decoupling caps 0.1nF (ceramic) across the plus / minus there could help.

Itsu

[AlienGrey]

Nick Z Nice scope display, nice scope, Is that the effect you're getting?
To me, it looks like you have found the resonant frequency of the yoke!
Try and see if you can improve on the effect that's happening between each off cycle (effect),
you can do this by changing the values of the 0.47 uf cap, try lowering it to get the 15 khz up a couple of cycles and see if it's amplitude increases, the fets should run cooler the. Try it and see how you get on.

PS don't bother with the Katcher yet.

Allen

PS some guys are experimenting with a winding under the grenade (equates to the grenades first layer in length).