Kapanadze Cousin - DALLY FREE ENERGY

[NickZ]

  Geo:
   The last picture that I posted was just to show what my old circuit could do to 5 100w bulbs,  which was taken about a year ago, or so.

  Today my circuit went into what Itsu calls the kaotic mode, first time in a while. Much brighter light bulbs, but the fets (especially one of them) heats to burning hot in just a couple of seconds. 
  I'll try your suggestion of using a bigger (1  1/2 inch) toroid, with 35 to 37 turns of 19 awg wire on it.

  Today I'm building a new Kacher secondary, using thicker wire, as my last secondary had 28awg on it, the new one will have 0.8 mm mag wire on it.
   I also replaced my antenna's ferrite choke with a whole new 3 inch one, as I had dropped the first one, and it broke into several pieces, which I couldn't find.

  Geo: Your new circuit is looking good. Keep up the good clean work...
           Thanks for the pics. 
   It will be interesting to see how you tune the circuit without a scope.
I haven't had much luck with that, but I'm not giving up, till death do us part.
Or something like that.

[NickZ]

   AlienGrey:
   To answer some of your questions, that you asked in the PM:
   I don't know about standing waves, so I won't try to answer that one.
   I have not finished my version of the Akula/Ruslan device, and I'm still working too modify and improve on what I already have.

   I've just added a new Kacher secondary coil, to try to get as close as possible to the superposition frequencies. But, I can't get the Kacher crt to oscillate yet.
  I'm still looking for something anomalous in the workings, but have not seen anything unusual, YET.
 

[GeoFusion]

  Geo:
   The last picture that I posted was just to show what my old circuit could do to 5 100w bulbs,  which was taken about a year ago, or so.

  Today my circuit went into what Itsu calls the kaotic mode, first time in a while. Much brighter light bulbs, but the fets (especially one of them) heats to burning hot in just a couple of seconds. 
  I'll try your suggestion of using a bigger (1  1/2 inch) toroid, with 35 to 37 turns of 19 awg wire on it.

  Today I'm building a new Kacher secondary, using thicker wire, as my last secondary had 28awg on it, the new one will have 0.8 mm mag wire on it.
   I also replaced my antenna's ferrite choke with a whole new 3 inch one, as I had dropped the first one, and it broke into several pieces, which I couldn't find.

  Geo: Your new circuit is looking good. Keep up the good clean work...
           Thanks for the pics. 
   It will be interesting to see how you tune the circuit without a scope.
I haven't had much luck with that, but I'm not giving up, till death do us part.
Or something like that.

Hi Nick,

Ahh alright, the pic is from previous / old circuit , the mazilli one.
Ah yes the Kaotic mode, Ringing mode of the ferrite yoke core, yes more output but yet it makes the circuit very fragile when
it it's working in that mode, so be careful.

Yes try that Nick, use a small toroid,  it can be the same sizes of toriods chokes you are using there but then using 0.8 mm (18 -19AWG )
it will remove the heat of the mosfets gradually, yet the toroid will get hot after a good while depending how much load
you are connecting. remember the PC fans

Alright awesome, looking forward to new winding on secondary, mines is 1.0mm  and short coil and the long kacher secondary you saw
in my last vid was 24awg.
Aw, that is sad to hear you broke one of your ferrite rods, Well lets see how it behaves with the replacement.

Thnx man, Yes clean work on this one is necessary, will be replicating these circuits as close as possible as the original ones.
Guessing this will be it, never experienced these types of TL494 circuits befor so, lets see the magic happen .
Tuning will happen when connecting various coils, caps and Bulbs for loading.
Already have a good ground too for the test , reminds me how I achieved resonance in a odd way
with RMG, caps and the coils to get 2000watts out. on 24 volts, but those where 42 caps in total of each 630V.

Do not give up,
We are so close to find what we all want! and this is for all of you on the forum that has a good heart and mind.
Recently I got usefull help and info from russian buddies, and got Ruslan to msg me in the past month in PS's.
the one important thing he told me  " Collect all Shark's Schematics and combine with his work"
The circuit I am building he tried it too. Well let's see how it works , there is more what we discussed,
and one more thing I want to say is , It needs to harvest the Ions around us and convert to usable,
it is in unlimited quantities around us.

Will keep the updates alive for the upcoming days,

  Cheerz~

[Acca]

 Hoppy new yar Ruslan from Ukraineskie kraij..

"My advice if you are a Russian: drink  much vodka: it makes only illusions of solving problems possible, happy new year. and piss off ...."

happy yar form Ukrainsky krai...

Sorri drunk two happi new yar
https://www.youtube.com/watch?v=hZ7SEWRD4vk

https://www.youtube.com/watch?v=H5ypQRRIGbY

[/font] ferite core  clip.. below...

https://www.youtube.com/watch?v=O8C-jU61lig

[tgraca]

ferrite core  clip.. below...
https://www.youtube.com/watch?v=O8C-jU61lig

Nice work! I like the steady barely-visible purple non-snapping stream of electric when the ferrite core is just to the side.
I wonder what the frequency is.