Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Kapanadze Cousin - DALLY FREE ENERGY

Started by 27Bubba, September 18, 2012, 02:17:22 PM

Previous topic - Next topic

0 Members and 103 Guests are viewing this topic.

Grumage

Quote from: NickZ on August 23, 2013, 01:06:00 PM
  So Grum, the first thing may be to get something made of iron to heat up in the big air coil. And if it does not heat up, then, make a separate coil of thick copper wire, made to test the induction heater type output.
  Then the next thing is to get the big air coil's inner choke to help raise the voltage back up to 110- 220volts Ac or higher, but with lots of amps.  Easier said than done...

Dear Nick.

I can raise stupidly high voltages on the choke at the resonant frequency. I have a 10 turn pickup coil on the choke who's turns are 255. I am using the probe on X100 and with the scope on it's max 5V/cm, the sine wave goes off the scale. But this is just volts little current.

The device just sits on the bench now. I have tried everything?? Divine intervention is the only thing left!! :) :) :) That or a VERY large hammer!!

Cheers Grum.

NickZ

  Yes, I understand. My set up is doing about the same thing. But, lets not give up, yet. 
Let's make the oscillator coils induction heater work, as the first step.
If you recall that's the route that Akula took, and Igor is going in the same direction.
  If this OU effect were easy it would have been found out about long ago.

MenofFather

Quote from: Grumage on August 23, 2013, 12:19:23 PM


The large Yellow tube is a Tesla secondary of 1000 turns of 0.25 wire on a 40 mm dia former. I am getting to know some Russian?? Please correct me if I am wrong?? :)

Yes, you right. Yelow is wound on 4 centimeters diameter tube 1000 turns with 0.25 milimeters diameter wire emulated, like in Tesla coil.

MenofFather

Quote from: magpwr on August 23, 2013, 04:55:50 AM
Hi everyone,

Base on the attachment which i have pointed.Can anyone advise me if by using HV from flyback transformer to the thick coil as shown in diagram.

Would this thick coil will be acting like a induction heater if a metal is placed in it.My question is would the metal eg:screwdriver get hot like those that we see in induction coil.But only this time it's a HV but low current source.

"[size=78%]Would this thick coil will be acting like a induction heater" [/size]
[size=78%]Brown coil i belive, that not acting like inductor heater.[/size]
[size=78%]
[/size]

gyulasun

Quote from: Grumage on August 23, 2013, 12:19:23 PM
...
Dear magpwr.

The large Yellow tube is a Tesla secondary of 1000 turns of 0.25 wire on a 40 mm dia former. I am getting to know some Russian?? Please correct me if I am wrong?? :)
...

Hi Grumage,

Sorry that I did not notice your above answer to magpwr and I answered quasi the same to him in my Reply#2213, just after your reply...  IT appeared to me that nobody has answered his question till my post.

greetings,  Gyula