Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Kapanadze Cousin - DALLY FREE ENERGY

Started by 27Bubba, September 18, 2012, 02:17:22 PM

Previous topic - Next topic

0 Members and 155 Guests are viewing this topic.

NickZ

  I notice that when I connect my 100x scope probes to the 168t output coil, it can kill the effect that the Kacher has on it, so I leave the black probe off, disconnected. It's not as accurate a reading that way, but it doesn't kill the effect.

Tomtech29

Quote from: NickZ on February 04, 2016, 05:15:53 PM
   Ground loops, huh???   
   Here's another short video I just uploaded of Tiger's device, to which I added the audio spectrum analyzer to see his running frequency.
   I thought that on that older Wesley video was also the running of the Lituania device, but, it's not.
So, Tiger's device is what's running on this video.

   https://www.youtube.com/watch?v=R7YCgIsGqVE
so between truth a demonstration increase the amplitude does not explain anything ,no shunt resistor and measuring the Rms to whom it is intended not as you think?
so just throw in a few cents :D

Jeg

Quote from: NickZ on February 04, 2016, 05:36:41 PM
  I notice that when I connect my 100x scope probes to the 168t output coil, it can kill the effect that the Kacher has on it, so I leave the black probe off, disconnected. It's not as accurate a reading that way, but it doesn't kill the effect.

It is because you insert probe's capacitance in parallel with grenade. This alters your grenade's resonant point.

Jeg

Quote from: GeoFusion on February 03, 2016, 06:17:41 PM
befor this accident I did reading on my amp clamp from mains to PSU was 1.1 amps!
Mains is 120V, Ran this for for sure 15 minutes without a problem. untill the ground removed.
and lit 420W worthy incandescents almost fully lit :) 7x 60W
As we can see there is Amplification and more output then input.


That is a good sign Geo even that Void's and Hoppy's opinion has to always been considered and i mean the ground loop possibility.
But i feel that it is a nice reference point for trying a self sustain operation.

Hoppy do you still use tvs at 30V at Katcher's power supply input?


Hoppy

Quote from: Jeg on February 05, 2016, 06:57:09 AM
That is a good sign Geo even that Void's and Hoppy's opinion has to always been considered and i mean the ground loop possibility.
But i feel that it is a nice reference point for trying a self sustain operation.

Hoppy do you still use tvs at 30V at Katcher's power supply input?

Jeg,

I dismantled my device way back after I had observed the URFA effect. This was with TVS diode suppression across the main 24V PSU output. I had intended to re-build with a new grenade but never got around to it.

As you say, Geo does have a nice reference point for further experimentation towards sustained operation at full effect.