Kapanadze Cousin - DALLY FREE ENERGY

[GeoFusion]

   Geo:   Ok, thanks. However, I already have a schematic and most of the components to build a controlable Kacher circuit, designed by Stalker. What I was asking about was not about the controlable circuit, but about the simple kacher circuit that I already have working. So, an interuptor circuit like the first one that Adrian once showed on the simple 5200 transistor kacher circuit, is what I'm looking for. Not the Akula nor Fet based controlable Kacher.

Nick:
You are welcome, I'm here to help.
Yes i know you are using the Stalker diagrams but
trust me to use this new diagram for the next step to make it really work.
It is the simple kacher that it is showing in the big diagram if you follow it but look what controls it is interesting and is
needed. Gonna show you a pic right here soon enough to show you what I mean
Thing is the kacher can't just free oscillate, it has to be interrupted ( short pulse )
and it ain't so hard to replicate something extra to it.
It will help and you will see results.
We are beyond the point to make this thing work as how it should now and we have everything to try it out right here
right now. The bigger reason why I am showing it is because Believe in it.

[NickZ]

  Geo:  Ok, I've seen the simple Kacher circuit that you are refering to now.Yes it is similar to my own version, but where is the interuptor circuit part (not shown). As that is what I am asking about.

[GeoFusion]

hello geo,
Could you explain the use of pin 3 in this TL494 circuit?
the circuit can work with pin 3 or not.
it seems to me that it has no use (it seems to me like an antenna only)
I'm very sorry, English is not my mother's speech and I don't understand it very well. Thank you.
I only use google translation
please make me a diagram of your kacher circuit.

Hi Soliman,
it is ok, you are doing your best and doing good in translation.
Pin 3 I'm not even using it in my setup. But it is the PWM comparator pin or feedback.
Not sure if it is used to auto tune while load is connected...Panov was not sure for what it was, written on the pic.
I traced the wire and pin 3 and it goes to the board before the kacher circuit, to a dip switch with 2 levers.
it is then connected to the CD4017 Chip. hmm
But that leg where PIN 3 is connected which is the C1 is the "clock input" leg #14 on the CD4017 Chip.
So to say CD407 is receiving Pulse signals from the TL494's pin3 white wire.
Hmmm Funny .. Might seem it works with the relay on the board maybe.
But to be sure it has to do with the start and stop of the system buttons.

In picture below you will see the pic of that circuit where the white wire is connected to the dip switch blue.
I have drawn arrows in red to show you what to see.

[GeoFusion]

  Geo:  Ok, I've seen the simple Kacher circuit that you are refering to now.Yes it is similar to my own version, but where is the interuptor circuit part (not shown). As that is what I am asking about.

Alright good.
yes it is a simple one.
Now do you see where on the minus leg of the Kacher is?
It is given a Orange color, orange wire which then goes to one side of a Mosfet if you follow the wire.
It connects to a IRFP3205.

The link to the diagram
https://i.imgur.com/p8ffNQW.jpg
I will do my best to show you on a modified pic if you have problems finding it. it is right there.



G

[Raycathode]

Alright good.
yes it is a simple one.
Now do you see where on the minus leg of the Kacher is?
It is given a Orange color, orange wire which then goes to one side of a Mosfet if you follow the wire.
It connects to a IRFP3205.

The link to the diagram
https://i.imgur.com/p8ffNQW.jpg
I will do my best to show you on a modified pic if you have problems finding it. it is right there.



G

Hi any chance you can ENLARGE the section your reference to wiring diagram is blurred (out of focus) cheers